Table saw

Table saw
Table saw
Sega circolare.jpg
A table saw, equipped for cutting large pieces of sheet stock.
Other names Sawbench
Classification Power tool
Manufacturer Bosch, Makita, Ryobi, Black & Decker/DeWalt, among others
The blade of a table saw cutting into wood

A table saw or sawbench is a woodworking tool consisting of a circular saw blade, mounted on an arbor, that is driven by an electric motor (either directly, by belt, or by gears). The blade protrudes through the surface of a table, which provides support for the material, usually wood, being cut.

In a modern table saw, the depth of the cut is varied by moving the blade up and down: the higher the blade protrudes above the table, the deeper the cut that is made in the material. In some early table saws, the blade and arbor were fixed, and the table was moved up and down to expose more or less of the blade. The angle of cut is controlled by adjusting the angle of blade. Some earlier saws angled the table to control the cut angle.


Types of table saws

A rudimentary table saw

There are four general classes of table saws: benchtop table saws, contractor table saws, cabinet table saws and hybrid table saws.

Benchtop table saws

Benchtop table saws are lightweight and are designed to be placed on a table or other support for operation. They commonly have direct drive (no v-belt or pulleys) from a universal type motor. They can be lifted by one person and carried to the job location. These saws often have parts made of steel, aluminum and plastic and are designed to be compact and light.

Benchtop table saws are the least expensive and least capable of the three major types; however, they can offer adequate capacity and precision for many tasks. The universal motor is not as durable or as quiet as a brushless AC motor, but it offers more power relative to its size and weight. The top of a benchtop table saw is narrower than those of the contractors and cabinet saws, so the width of stock that can be ripped is reduced. Another restriction results from the top being smaller from the front of the tabletop to the rear. This results in a shorter rip fence, which makes it harder to make a clean, straight cut when ripping. Also, there is less distance from the front edge of the tabletop to the blade, which makes cross cutting stock using a mitre more difficult (the mitre and/or stock may not be fully supported by the table in front of the blade). Benchtop saws are the smallest type of table saw and have the least mass, potentially resulting in increased vibration during a cut.

Contractor table saws

Contractor table saws are heavier, larger and have an attached stand or base, often with wheels. The motor hinges off the rear of the saw and drives the blade via one, or occasionally two, belts using a 1 to 2 hp (750 to 1500 W) induction type motor. This is the type often used by hobbyists and homeowners because standard electrical circuits provide adequate power to run it, and due to its low cost. Because the motor hangs off the rear of the saw on a pivot, dust collection can be problematic in comparison with a cabinet saw.

Cabinet table saws

Cabinet table saws are heavy (using large amounts of cast iron and steel) to minimize vibration and increase accuracy. A cabinet saw is characterized by having a closed (cabinet) base. Cabinet saws usually have induction motors in the 3 to 5 hp (2 to 4 kW) range. For home use, this type of motor typically requires that a heavy-duty circuit be installed (in the US, this requires a 220V outlet). The motor is enclosed within the cabinet and drives the blade with three parallel v-belts. Cabinet saws are heavier and offer the following advantages over contractor saws: heavier construction for lower vibration and increased durability; a cabinet-mounted trunnion (the mechanism that incorporates the saw blade mount and allows for height and tilt adjustment); improved dust collection due to the totally enclosed cabinet and common incorporation of a dust collection port. In general, cabinet-mounted trunnions are easier to adjust than table-mounted trunnions.

American-style cabinet saws generally follow the model of the Delta Unisaw, a design that has evolved since 1939.[citation needed] Saws of this general type are made in the USA, Canada and China. These saws are characterized by a cast iron top on a full-length steel base, square in section, with radiussed corners. Two 3/8" deep by 3/4" wide miter slots are located parallel to the blade, one to the left of the blade and one to the right. The most common type of rip fence mounted to this type of saw is characterized by the standard model made by Biesemeyer. It has a sturdy, steel T-type fence mounted to a steel rail at the front of the saw. It has replaceable laminate faces. American cabinet saws are normally designed to accept a 13/16" wide stacked dado blade in addition to a standard saw blade. The most common size of blade capacity is 10" in diameter. The blade arbor has a diameter of 5/8". American saws normally include an anti-kickback device that incorporates a splitter, toothed anti-kickback pawls and a clear plastic blade cover. American style saws have an easily replaceable insert around the blade in the table top. This allows the use of zero-clearance inserts, which greatly reduce tear out on the bottom of the workpiece. It is common for this type of saw to be equipped with a table extension that increases ripping capacity for sheet goods. American style table saws are commonly available with the option of left or right tilt blade capability. While relatively simple in design, these saws are highly evolved and capable of efficient and precision work.

European-style cabinet saws are often more complex and modern in design compared to American types. They often are equipped with a sliding table to make cross cuts easier and safer than by the use of an American style mitre gauge. Unless modified for the American market, European table saws are not equipped to allow the use of a stacked dado blade set (this is due to safety laws in European markets). Rip fences on European saws tend to be of lighter construction and less smooth in operation compared to American cabinet saws. European cabinet saws are often available in multi-purpose tool configurations that can offer jointer, planer, shaper or boring features. The blade arbor typically has a diameter of 30mm, though for the American market a 5/8" arbor is commonly available as an option. Note that American woodworkers are likely to use a stacked dado blade to cut dados (square sectioned grooves) where European woodworkers might use a shaper or other tool for this task. European cabinet saws often incorporate a riving knife to prevent kickback. Riving knives differ from American style splitters in that they rise and fall with the blade (splitters are fixed in place without regard for the height that the blade is adjusted to). European cabinet saws often offer as an option a scoring blade, which is a second, smaller diameter blade mounted in front of the regular saw blade. The scoring blade helps reduce splintering in certain types of stock, especially laminated stock.

Hybrid table saws

Hybrid table saws are designed to compete in the market with high-end contractor table saws. They offer some of the advantages of cabinet saws at a lower price than traditional cabinet saws. Hybrid saws on the market today offer an enclosed cabinet to help improve dust collection. The cabinet can either be similar to a cabinet saw with a full enclosure from the table top to the floor or a shorter cabinet on legs. Some hybrid saws have cabinet-mounted trunnions and some have table-mounted trunnions. Hybrid saws tend to be heavier than contractor saws and lighter than cabinet saws. Some hybrid saws offer a sliding table as an option to improve cross cutting capability. Hybrid saw drive mechanisms vary more than contractor saws and cabinet saws. Drive mechanisms can be a single v-belt, a serpentine belt or multiple v-belts.


In the United States, perhaps the first recorded patent for the circular saw was issued in 1777 to an English man, Samuel Miller; it refers to a circular saw that was created in Holland in the 16th or 17th centuries.[1] The 1885 catalog of the W.F. & John Barnes Co., Rockford, Il. clearly shows a classic table saw and it is labeled as a "Hand [Powered] Circular Rip Saw".

Product Recall

In the history of mechanical devices, there are always product recalls from the market. In th case of table saws, there have been several product recalls recorded since 2002. Here is the list:

  • On August 22, 2002 Black & Decker recalled its Black & Decker BT2500 model. This recall involved Taiwanese made table saws, mostly from the BT2500 series, having date codes 200128-CT through 200148-CT. The saws were recalled because of electric shock. Several incidents were reported, but no injuries.[2]
  • On December 6, 2004 Robert Bosch Tool Corp. recalled its Skil® Table Saw Model 3400 from the market. The blade drive mechanism may loosen or the motor can separate from the tool, which can lead to kickback of the item being sawed, resulting in possible laceration. There have been eleven reports of loose or broken motors, but no injuries have been reported.[3]
  • On April 7, 2005 Sears Roebuck and Company recalled its Table Saw due to problematic rip fences. This recall involved table saws manufactured by Rexon Industrial Corp. Ltd. [4]
  • On April 29, 2008 DEWALT recalled its DEWALT DW744 Jobsite Table Saws due to a laceration hazard. The recall covers 13,000 units.[5]
  • On August 19, 2009 One World Technologies recalled its Rigid 10-inch Table Saws due to a laceration hazard. The recall covers 3,000 units.[6]


Causes of table saw injuries include:[citation needed]

The use of a push stick reduces the risk of injury.
  • Failure to read warning labels and the owner's manual before use.
  • When the saw is not in use, leaving the blade projecting above the table.
  • Not disconnecting power when performing maintenance or changing blades.
  • Not using a push stick or other such safety device when making cuts that otherwise require fingers to be close to the blade.
  • Using the saw in a way that fingers advance into the path of the blade.
  • Failing to be alert and pay consistent attention. This piece of equipment causes more serious injuries than anything else in the shop. Many experienced woodworkers know someone who have lost a finger.
  • Removing the blade guard. If the original guard is unsatisfactory, aftermarket guards are available in various configurations. Note that one main function of a typical blade guard is to act as a splitter, which helps prevent the cut in the wood from closing and pinching the back of the blade and kicking back. Sometimes the blade guard is more of a danger than a safety feature, most commonly during smaller cuts (less than 3 inches), and cuts with a push stick, and should be removed.
  • Wood being cut can violently kick back. This is due to advancing the wood in a sinuous line or because natural stresses in the wood cause the cut to pinch the back of the saw blade. This can be strong enough to cause the material to jolt backwards and result in serious injury to the operator. The use of the splitter or a riving knife can reduce or eliminate this problem. See Avoiding Kickback
  • Not wearing eye protection. The rotational mass of a spinning saw blade combined with a large electric motor can contribute to the violent and unexpected ejection of material. Wearing unsuitable safety glasses that don't fully encompass the eye area, including the front and sides of the eye, can also result in injuries. Good safety glasses are comfortable so they are always worn when needed.
  • Lack of ear protection. Extremely loud noises as well as prolonged fairly loud noises can contribute to hearing loss as well as tinnitus.
  • Wearing clothing that's excessively loose-fitting, and failing to tie back long hair. These are dangerous if they come in contact with the blade. Cuffs should also be buttoned if wearing a long-sleeved shirt.
  • Maladjusted blade not perfectly parallel with the fence and the miter slots. If it is not parallel, the workpiece can often become pinched between the blade and the fence, inducing violent kickback and causing injury.
  • Not pushing the material past the saw when finishing a cut. These pieces can get caught and violently drawn into the blade, resulting in kickback.
  • Failing to operate defensively. The nature of wood includes variations in structure and internal forces, and its not uncommon for natural stresses in a piece of wood to cause the blade to be pinched and thrown violently. So cautious working is important.

Safety practices

Avoiding kickback

Kickback happens when the blade catches the workpiece and violently throws it back to the front of the saw, towards the operator. It can be thrown very hard and can injure the operator. It is not uncommon for the object to have high enough velocity to become embedded in a wall or to cause other damage or injury. Never stand in a direct line between the blade and the fence when ripping narrow stock. A kickback can be fatal.

Kickback happens when ripping if:

  1. The wood pinches the blade because of internal stresses. This is difficult to predict and can be impossible to control when using fingers to hold the wood down. Many times the board pinches the blade and is thrown back before the wood reaches a splitter. This type of kickback never happens when a board is not cut all the way through (dado). By starting a cut with a dado and then raising the blade to leave a splitter tab of uncut wood, this type of kickback can be avoided, but raising the blade during a cut cannot be done unless anti-kickback hold downs are used, so it is safe to raise the blade with a free hand.
  2. The wood is allowed to raise up or moved sideways during a cut, then pushed back down, taking too big a bite at the top of the blade. This can be prevented by using feeder wheels very close to the start of the blade and hold downs after the blade to control the wood all the way through the cut. The right feeder wheels are very effective for both dados in plywood and for rip cuts on boards as narrow as 1/8". Feeder wheels can be powered or unpowered, clamped or held magnetically, and replace fingers near the blade so a hand can be free to turn off the saw during a cut.
  3. The board is pinched between the rear of the blade and the fence. The fence should be parallel with the blade, for the best cut on both sides of the blade. The fence can be set with the rear farther from the fence for safety, but at the expense of upcut marks on the "waste" piece. Never allow the fence to be closer to the rear of the blade than the front.

Kickback can also happen when crosscutting boards with internal stresses. A chop saw or circular saw is the best preference for cutting poor lumber.[citation needed]

The risk of kickback is reduced by certain practices:

  • The blade must be kept sharp and clean, something novice users may not recognize. The buildup of pitch on a blade greatly increases friction and increases the probability of kickback. It also decreases the quality of the cut, causing it to burn.
  • The saw must be aligned, adjusted so that it is parallel to the miter grooves, with the rip fence should angled minutely. If the blade is parallel with the fence you will notice the marks made by the back of the blade on the wood. It is possible for the workpiece to be pinched between the blade and the rip fence, which will cause violent kickback if the fence is closer at the back of the blade. The correct relationship for the fence is minutely spread which means that the angle is different depending on the side of the blade the fence is set.
  • The blade guard should be used whenever possible. Typical table saws incorporates a riving knife, a spreader which helps prevent the cut from closing on the back of the saw blade. Natural tension can exist in wood that causes the cut to close. Some blade guards have anti-kickback devices that allow only forward travel past the blade.
  • Push the workpiece past the blade. Do not release a workpiece until it is past the blade and removed from the saw. Turn the saw off before removing small cut off pieces.
  • Always maintain control. Do not execute a cut where you do not have complete control of the situation. Make sure there are no obstructions. Do not cut a workpiece that is too large to handle.
  • Do not use the rip fence as a guide during crosscuts. If you need to make a series of equal length crosscuts, use a stop block in front of the blade so the workpiece is not in contact with the rip fence during the cut. It is easy for the workpiece to twist out of perpendicular at the end of the cut and thus get caught by the blade and thrown.
  • Check for flaws in the wood. Cutting through a loose knot can be dangerous. Cutting a warped or twisted board along the rip fence is dangerous because it can get pinched between the fence and blade.

Optional safety features

In recent years, new technology has been developed which can dramatically reduce the risk of serious injury caused by table saws. One way to prevent fingers from being severed is to use springs or feeder wheels to apply pressure on the side and top of the lumber when ripping. These feather boards and push sticks are substitutes for fingers. Traditionally they are clamped to a saw top.

A dust extractor should be fitted. If sawdust is prone to build up under the cutting blade, through friction the spinning blade will quickly ignite the accumulated dust, and the smoke can be mistaken for an overheated blade. The extractor also reduces the risk of a dust explosion and facilitates a healthier working environment.

Magnetic featherboard

The magnetic featherboard was developed in 1990.[citation needed] It is held to a cast iron table top or steel fence plate by high strength magnets. The fence mounted feeder has roller wheels which pull wood to the fence. These roller guides are used both before and after the cut and allow cuts with no fingers near the blade. Power feeders are a motorized version with rubber wheels which take the place of hands and assure constant pressure.

Automatic braking

One new feature, commercially available in saws since 2005,[7] is an automatic braking system. The feature's inventor, after trying to license it to manufacturers without success, started SawStop, based in Tualatin, Oregon. SawStop's saws applies a small amount of electric current to the blade of the saw. This current is continuously monitored. If the saw detects a change in this current (as would occur if a hand or other body part came into contact with the blade) an automatic braking system is activated, forcing an aluminum brake block into the blade. The saw stops within five milliseconds, and angular momentum lowers the blade into the table. The operator suffers a small nick instead of an amputation or other more serious injury.[8]

There is a chance this may ruin the blade, however.[9] The feature is impractical to retrofit into existing table saw. The feature must also be bypassed when cutting wet timber.

Blade height

Ideally the blade of the table saw should extend higher than the board being cut by about a quarter of an inch; this lessens the risk of kickback and other injuries and enables smooth cutting.

There are two competing schools of thought when it comes to properly setting the height of the blade for sawing. The first is commonly expressed thus:[citation needed] "Only allow the blade to rise above the work by the amount of finger you wish to lose." That is, the blade should protrude above the piece as little as possible, to prevent the loss of a finger in case of a sawing accident.

Another competing view is that the saw functions at its best when the angle of the blade teeth arc relative to the top surface of the workpiece is as extreme as possible.[citation needed] This facilitates chip ejection, shortens the overall distance through which the teeth act on the part, reduces power consumption and heat generation, substantially reduces the peak pushing force required, thus improving control, and causes the blade's force on the wood to act mostly downward rather than largely horizontally.


  • Outfeed tables: Table saws are often used to rip long boards or sheets of plywood or other sheet materials. The use of an out feed (or outfeed) table makes this process safer and easier. Many of these are shop built, while others are commercially available.
  • Infeed tables: Used to assist feeding long boards or sheets of plywood. In the past roller stands were pretty much the only option, but there are now commercially available infeed units that are more efficient and easier to use.
  • Rip fence: Table saws commonly have a fence (guide) running from the front of the table (the side nearest the operator) to the back, parallel to the cutting plane of the blade. The distance of the fence from the blade can be adjusted, which determines where on the workpiece the cut is made. The fence is commonly called a "rip fence" referring to its use in guiding the workpiece during the process of making a rip cut. Most table saws come standard with a rip fence, however some high end saws are available without a fence so a fence of the user's choice can be purchased separately.
  • Feather board: Featherboards are used to keep wood against the rip fence. They can be a single spring, or many springs, as made from wood in many shops. They are held in place by high strength magnets, clamps, or expansion bars in the miter slot.
  • Hold down: The circular sawblade of a tablesaw will pick up a piece of wood if not held down. Hold downs can be a vertical version of featherboards, attached to a fence with magnets or clamps. Another type of hold down uses wheels on a spring-loaded mechanism to push down on a workpiece as it is guided past the blade.
  • Sub fence: A piece of wood clamped to the rip fence allows a dado set to cut into the rip fence, allowing rabbet cuts with a dado blade.
  • Miter gauge: The table has one or two slots (grooves) running from front to back, also parallel to the cutting plane of the blade. These miter slots (or miter grooves) are used to position and guide either a miter gauge (also known as a crosscut fence) or crosscut sled. The miter gauge is usually set to be at 90 degrees to the plane of the blade's cut, to cause the cut made in the workpiece to be made at a right angle. The miter gauge can also be adjusted to cause the cut to be made at a precisely controlled angle (a so-called miter cut).
  • Crosscut sled: A crosscut sled is generally used to hold the workpiece at a fixed 90 degree angle to the blade, allowing precise repeatable cuts at the most commonly used angle. The sled is normally guided by a runner fastened under it that slides in a miter slot. This device is normally shop made, but can be purchased.
  • Tenon jig: A tenon jig is a device that holds the workpiece vertically so cuts can be made across the end. This allows tenons to be formed. Often this is a purchased item, but it can be shop made. The tenon jig is guided by a miter slot or a fence.
  • Stacked dado: Saws made for the US market are generally capable of using a stacked dado blade set. This is a kit with two outer blades and a number of inner chip cutters that can be used to cut dados (grooves in the workpiece) of any width up to the maximum (generally 7/8 of an inch). Stacked dado sets are available in 6 inch and 8 inch diameters. 8 inch stacked dado sets are not recommended for saws with 112 or fewer HP.
  • Inserts: Table saws have a changeable insert in the table through which the blade projects. Purchasable inserts are usually made out of metal. Zero-Clearance inserts can be made of a sawable material such as plastic or wood. When a Zero-Clearance insert is initially inserted, the blade is raised through the insert creating the slot. This creates a slot with no gaps around the blade. The zero clearance insert helps prevent tearout by providing support for wood fibers right next to the blade thus helping to make a very clean cut. Other inserts can be bought or created in the same manner, such as a dado insert.
  • Splitter: A splitter or riving knife is a vertical projection located behind the saw blade. This can be a pin or a fin. It is slightly narrower in width than the blade and located directly in line with the blade. The splitter prevents the material being cut from being rotated thereby helping to prevent kickback. Splitters may incorporate pawls, a mechanism with teeth designed to bite into wood and preventing kickback.

Operating a saw without a splitter is the cause of many injuries, yet is considered by many to be unnecessary. This is one of the most useful safety devices on a table saw, and while people go years without using one, and feel they are for those with less experience, serious injury or death can occur, regardless of experience.[10]

Splitters can take many forms, including being part of the blade guard that comes standard with the saw. Another type of splitter is simply a vertical pin or fin attached to an insert. Splitters are available commercially or can be made from wood, metal or plastic.


Specific references:

General references:

Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • table saw — n. a circular saw mounted on the underside of a table through which its blade projects: work to be sawed is placed on the table * * * …   Universalium

  • table saw — n. a circular saw mounted on the underside of a table through which its blade projects: work to be sawed is placed on the table …   English World dictionary

  • table saw — noun a circular saw mounted under a table or bench so that the blade of the saw projects up through a slot • Hypernyms: ↑circular saw, ↑buzz saw …   Useful english dictionary

  • table saw — noun A circular saw mounted beneath the surface of a table, the rotating blade protruding up through a slot …   Wiktionary

  • Saw — Saw, n. [OE. sawe, AS. sage; akin to D. zaag, G. s[ a]ge, OHG. sega, saga, Dan. sav, Sw. s[*a]g, Icel. s[ o]g, L. secare to cut, securis ax, secula sickle. Cf. {Scythe}, {Sickle}, {Section}, {Sedge}.] An instrument for cutting or dividing… …   The Collaborative International Dictionary of English

  • Saw bench — Saw Saw, n. [OE. sawe, AS. sage; akin to D. zaag, G. s[ a]ge, OHG. sega, saga, Dan. sav, Sw. s[*a]g, Icel. s[ o]g, L. secare to cut, securis ax, secula sickle. Cf. {Scythe}, {Sickle}, {Section}, {Sedge}.] An instrument for cutting or dividing… …   The Collaborative International Dictionary of English

  • Saw file — Saw Saw, n. [OE. sawe, AS. sage; akin to D. zaag, G. s[ a]ge, OHG. sega, saga, Dan. sav, Sw. s[*a]g, Icel. s[ o]g, L. secare to cut, securis ax, secula sickle. Cf. {Scythe}, {Sickle}, {Section}, {Sedge}.] An instrument for cutting or dividing… …   The Collaborative International Dictionary of English

  • Saw frame — Saw Saw, n. [OE. sawe, AS. sage; akin to D. zaag, G. s[ a]ge, OHG. sega, saga, Dan. sav, Sw. s[*a]g, Icel. s[ o]g, L. secare to cut, securis ax, secula sickle. Cf. {Scythe}, {Sickle}, {Section}, {Sedge}.] An instrument for cutting or dividing… …   The Collaborative International Dictionary of English

  • Saw gate — Saw Saw, n. [OE. sawe, AS. sage; akin to D. zaag, G. s[ a]ge, OHG. sega, saga, Dan. sav, Sw. s[*a]g, Icel. s[ o]g, L. secare to cut, securis ax, secula sickle. Cf. {Scythe}, {Sickle}, {Section}, {Sedge}.] An instrument for cutting or dividing… …   The Collaborative International Dictionary of English

  • Saw gin — Saw Saw, n. [OE. sawe, AS. sage; akin to D. zaag, G. s[ a]ge, OHG. sega, saga, Dan. sav, Sw. s[*a]g, Icel. s[ o]g, L. secare to cut, securis ax, secula sickle. Cf. {Scythe}, {Sickle}, {Section}, {Sedge}.] An instrument for cutting or dividing… …   The Collaborative International Dictionary of English

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”