Soldering iron

Soldering iron

Infobox tool
name = Soldering iron

caption =A gas fired soldering iron
other_name =Soldering Gun
classification = Metal joining
types =
related = Brazing
A soldering iron is a device for applying heat to melt solder for attaching two metal parts.

A soldering iron is composed of a heated metal tip and an insulated handle. Heating is often achieved electrically, by passing a current, supplied through an electrical cord or a battery, through a heating element. Another heating method includes combustion of a suitable gas, which can either be delivered through a tank mounted on the iron (flameless), or through an external flame.

Some heat up and cool down in a few seconds, but others take minutes.

Irons for electrical or electronics work

For electrical work, wires are usually soldered to printed circuit boards, other wires, or small terminals. A low-power iron (15-30 Watts) is suitable for this work. In earlier days wires were frequently soldered to large chassis made of heavy metal, but this high-power requirement is now rare. Higher power is used for non-electrical metal-work.

Small battery-operated or gas soldering irons are useful when there isn’t a convenient source of electricity.

Some soldering irons have interchangeable tips for different types of work. Pyramid tips with a triangular flat face are useful for soldering sheet metal. Fine round or chisel tips are typically used for electronics work.

Stands for irons

A soldering iron stand keeps the iron away from flammable materials, and often also comes with a sponge and flux pot for cleaning the tip. Some soldering irons for continuous and professional use come as part of a "soldering station," which allows the exact temperature of the tip to be adjusted, kept constant, and displayed.

Using a soldering iron

For best results, particularly in electrical work where good electrical contact is required, the iron should be used to heat the work piece, and solder applied to it: this helps to prevent "cold joints", where hot solder is applied by the iron to a relatively cold target, shrouding it in solder to look like a good joint, but without wetting it properly, and without forming a good connection.

Some electrical solder contains flux cores (the purpose of the flux is to clean the oxides off the metals to permit a good joint). If the solder is applied to the iron first then the flux is rapidly burnt off (the wispy white smoke you get from the tip of the iron) and cannot serve its purpose on the joint. In heavier applications, including plumbing, flux is normally applied completely separately.

Temperature-controlled soldering station

A temperature-controlled soldering station is a complete unit usually used for soldering electronic components, and consisting of an electrical power supply, a soldering iron, and is different for lead-based and lead-free solders. Lead-based solder uses 250°C to 280°C or 300°C while lead-free soldering needs a higher temperature, about 350°C to 400°C.

A variety of means are used to control temperature.

The simplest of these is a variable power control, much like a light dimmer, which together with the loss of heat from the iron to the environment roughly sets the temperature.

More complex is some form of thermostat, which is often inside the tip itself, which switches power on and off to the elements.

Another approach to use magnetized soldering tips which lose their magnetic properties at a certain temperature (the curie point). As long as the tip is magnetic, it clings to the heating element. At the design temperature, it loses contact, cooling down.

Other complex irons similar to those produced under the Metcal brand, circulate a high frequency AC current through the tip, and using magnetic physics to direct heating only where the surface of the tip drops below the curie point.

The most advanced soldering irons are digital and control temperature via a microprocessor in the station that monitors a thermocouple inside the tip, increasing or decreasing the power on the tip based on the selected temperature. Brands like JBC and a few models from ERSA and Weller use this heating system.


When burnt flux and oxidised material begins to accumulate on the tip, it blocks heat transfer and contaminates the joint, making soldering difficult or impossible.

Many soldering stations come with a sponge which is dampened, and used to wipe the hot iron's tip clean. Wet denim performs the same job.

A small amount of fresh solder is usually then applied to the clean tip in a process called tinning.A metal edge is sometimes used carefully to remove very severe oxidisation, though this risks damaging plating.

The working surface of the tip should be kept tinned (coated with wet solder) to minimise oxidation. Oxidation blocks heat transfer, corrodes the tip and contaminates the joint.

Tip design


Older and very cheap irons typically use a bare copper tip, which is shaped with a file or sandpaper.This dissolves comparatively rapidly into the solder, suffering pitting and erosion of the shape.


Recent soldering iron tips tend to be plated copper, to increase the lifetime by many times. The plating resists erosion by the molten solder, which is especially severe at high temperatures needed for modern lead-free solders.

oldering iron tip maintenance

Bare copper tips that are repeatedly resurfaced, as typically found on old high power irons, can last decades in use, and the shaft of the copper tip is prone to corrosion over such long times. It is therefore best practice to remove and wire-brush the bit to remove shaft corrosion about once a decade, to maintain effective thermal contact with the iron.

With the very few irons that use a steel tip, this needs carrying out more frequently, as tip shaft corrosion (rust) is liable to break the iron.

Ready made tips for old irons are not always available. When needed, replacements are made from any suitable piece of copper, or if necessary a copper alloy.

Other uses

Soldering irons can be used for many tasks that require a controlled source of heat. This will often damage the iron, or make it difficult to use for its proper purpose.

These include:
* pyrography - Burning designs into wood.
* plastic welding - using the iron to melt and join plastics.
* hot-wire foam cutter - Cutting foam with a hot wire

ee also

* Solder
* Brazing - Joining metals structurally by the use of a higher temperature joining alloy than solder.
* Welding - Melting two objects to be joined into each other.
* ColdHeat - A simple 'instant heat' soldering iron

Notes and References

External links

* [ Basic Soldering Guide] A good portion of this site is devoted to the tools to use while soldering and their care
* [ The Art of Soldering] This article briefly touches on soldering irons.

Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Soldering iron — Soldering Sol der*ing, a. & n. from {Solder}, v. t. [1913 Webster] {Soldering iron}, {Soldering tool}, an instrument for soldering, consisting of a bit or bolt of copper having a pointed or wedge shaped end, and furnished with a handle. [1913… …   The Collaborative International Dictionary of English

  • soldering iron — soldering irons N COUNT A soldering iron is a tool used to solder things together …   English dictionary

  • soldering iron — soldering .iron n a tool which is heated, usually by electricity, and used for melting solder and putting it on surfaces …   Dictionary of contemporary English

  • soldering iron — ► NOUN ▪ an electrical tool for melting and applying solder …   English terms dictionary

  • soldering iron — [säd′ər iŋ] n. a pointed metal tool heated for use in melting and applying solder …   English World dictionary

  • soldering iron — noun a hand tool with a heatable tip; used to melt and apply solder • Hypernyms: ↑hand tool * * * noun, pl ⋯ irons [count] : a tool that is electrically heated and used for joining parts with solder * * * ˈsoldering iron [soldering iron soldering …   Useful english dictionary

  • soldering iron — UK [ˈsɒldərɪŋ ˌaɪə(r)n] / US [ˈsɑdərɪŋ ˌaɪrn] noun [countable] Word forms soldering iron : singular soldering iron plural soldering irons a tool used for heating solder and joining metal surfaces together …   English dictionary

  • soldering iron — noun Date: 1688 a pointed or wedge shaped device that is usually electrically heated and that is used for soldering …   New Collegiate Dictionary

  • soldering-iron — /ˈsɒldərɪŋ aɪən/ (say solduhring uyuhn) noun a tool used for soldering …  

  • soldering iron — sol|der|ing iron [ sadərıŋ ,aırn ] noun count a tool used for heating solder and joining metal surfaces together …   Usage of the words and phrases in modern English

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”