- Power steering
-
Power steering helps drivers steer vehicles by augmenting steering effort of the steering wheel. It does this by adding controlled energy to the steering mechanism, so the driver needs to provide only modest effort regardless of conditions. In particular, power steering helps considerably when a vehicle is stopped or moving slowly. As well, power steering provides some feedback of forces acting on the front wheels to give an ongoing sense of how the wheels are interacting with the road; this is typically called "rοad feel"·
Representative power steering systems for cars augment steering effort via an actuator, a hydraulic cylinder, which is part of a servo system. These systems have a direct mechanical connection between the steering wheel and the linkage that steers the wheels. This means that power-steering system failure (to augment effort) still permits the vehicle to be steered using manual effort alone.
Other power steering systems (such as those in the largest off-road construction vehicles) have no direct mechanical connection to the steering linkage; they require power. (These are technically position servos.) Systems of this kind, with no mechanical connection, are sometimes called "drive by wire" or "steer by wire", by analogy with aviation's "fly-by-wire". In this context, "wire" refers to electrical cables that carry power and data, not thin-wire-rope mechanical control cables.
In other power steering systems, electric motors provide the assistance instead of hydraulic systems. As with hydraulic types, power to the actuator (motor, in this case) is controlled by the rest of the power-steering system.
Some construction vehicles have a two-part frame with a rugged hinge in the middle; this hinge allows the front and rear axles to become non-parallel to steer the vehicle. Opposing hydraulic cylinders move the halves of the frame relative to each other to steer.
Contents
History
The first power steering system on an automobile was apparently installed in 1876 by a man with the surname of Fitts. Little else is known about him. The next power steering system was put on a Columbia 5-ton truck in 1903.[1]
Robert E. Twyford, a resident of Pittsburgh, Pennsylvania, USA, included a mechanical power steering mechanism as part of his patent (U.S. Patent 646,477) issued on April 3, 1900 for the first four wheel drive system.[2]
Francis W. Davis, an engineer of the truck division of Pierce Arrow began exploring how steering could be made easier, and in 1926 invented and demonstrated the first practical power steering system.[3][4][5] Davis moved to General Motors and refined the hydraulic-assisted power steering system, but the automaker calculated it would be too expensive to produce.[6] Davis then signed up with Bendix, a parts manufacturer for automakers. Military needs during World War II for easier steering on heavy vehicles boosted the need for power assistance on armored cars and tank-recovery vehicles for the British and American armies.[6]
Chrysler Corporation introduced the first commercially available passenger car power steering system on the 1951 Chrysler Imperial under the name "Hydraguide".[7] The Chrysler system was based on some of Davis' expired patents. General Motors introduced the 1952 Cadillac with a power steering system using the work Davis had done for the company almost twenty years earlier.[8]
Charles F. Hammond, an American, born in Detroit, filed several patents for improvements of power steering with the Canadian Intellectual Property Office in 1958.[9][10][11]
Most new vehicles now have power steering, owing to the trends toward front wheel drive, greater vehicle mass, and wider tires, which all increase the required steering effort. Heavier vehicles as common in some countries would be extremely difficult to maneuver at low speeds, while vehicles of lighter weight may not need power assisted steering at all.
Hydraulic systems
Most power steering systems work by using a hydraulic system to steer the vehicle's wheels.[citation needed] The hydraulic pressure typically comes from a gerotor or rotary vane pump driven by the vehicle's engine. A double-acting hydraulic cylinder applies a force to the steering gear, which in turn steers the roadwheels. The steering wheel operates valves to control flow to the cylinder. The more torque the driver applies to the steering wheel and column, the more fluid the valves allow through to the cylinder, and so the more force is applied to steer the wheels.
One design for measuring the torque applied to the steering wheel has a torque sensor – a torsion bar at the lower end of the steering column. As the steering wheel rotates, so does the steering column, as well as the upper end of the torsion bar. Since the torsion bar is relatively thin and flexible, and the bottom end usually resists being rotated, the bar will twist by an amount proportional to the applied torque. The difference in position between the opposite ends of the torsion bar controls a valve. The valve allows fluid to flow to the cylinder which provides steering assistance; the greater the "twist" of the torsion bar, the greater the force.
Since the hydraulic pumps are positive-displacement type, the flow rate they deliver is directly proportional to the speed of the engine. This means that at high engine speeds the steering would naturally operate faster than at low engine speeds. Because this would be undesirable, a restricting orifice and flow-control valve direct some of the pump's output back to the hydraulic reservoir at high engine speeds. A pressure relief valve prevents a dangerous build-up of pressure when the hydraulic cylinder's piston reaches the end of its stroke.
Some modern systems also include an electronic control valve to reduce the hydraulic supply pressure as the vehicle's speed increases; this is variable-assist power steering.
The steering booster is arranged so that should the booster fail, the steering will continue to work (although the wheel will feel heavier). Loss of power steering can significantly affect the handling of a vehicle. Each vehicle owner's manual gives instructions for inspection of fluid levels and regular maintenance of the power steering system.
The working liquid, also called "hydraulic fluid" or "oil", is the medium by which pressure is transmitted. Common working liquids are based on mineral oil.
DIRAVI
Main article: DIRAVIIn the DIRAVI system invented by Citroën, the force steering the wheels comes from the car's high pressure hydraulic system and is always the same no matter what the road speed is. Turning the steering wheel moves the wheels simultaneously to a corresponding angle via an hydraulic cylinder. In order to give some artificial steering feel, there is a separate hydraulically operated system that tries to turn the steering wheel back to centre position. The amount of pressure applied is proportional to road speed, so that at low speeds the steering is very light, and at high speeds it is very difficult to move more than a small amount off centre.
As long as there is pressure in the car's hydraulic system, there is no mechanical connection between the steering wheel and the roadwheels. This system was first introduced in the Citroën SM in 1970, and was known as 'VariPower' in the UK and 'SpeedFeel' in the U.S.
While DIRAVI is not the mechanical template for all modern power steering arrangements, it did innovate the now common benefit of speed sensitive steering.
In the late 1960s, General Motors offered a variable-ratio power steering system as an option on Pontiac and other vehicles.
Electro-hydraulic systems
Electro-hydraulic power steering systems, sometimes abbreviated EHPS, and also sometimes called "hybrid" systems, use the same hydraulic assist technology as standard systems, but the hydraulic pressure comes from a pump driven by an electric motor instead of a drive belt at the engine.
In 1965, Ford experimented with a fleet of "wrist-twist instant steering" equipped Mercury Park Lanes that replaced the conventional large steering wheel with two 5-inch (127 mm) rings, a fast 15:1 gear ratio, and an electric hydraulic pump in case the engine stalled.[12][13]
In 1990, Toyota introduced its second-generation MR2 with electro-hydraulic power steering. This avoided running hydraulic lines from the engine (which was behind the driver in the MR2) up to the steering rack. In 1994 Volkswagen produced the Mark 3 Golf Ecomatic, with an electric pump. This meant that the power steering would still operate while the engine was stopped by the computer to save fuel.[14] Electro-hydraulic systems can be found in some cars by Ford, Volkswagen, Audi, Peugeot, Citroen, SEAT, Skoda, Suzuki, Opel, MINI, Toyota, Honda, and Mazda.
Servotronic
Servotronic offers true speed-dependent power steering, in which the amount of servo assist depends on road speed, and thus provides even more comfort for the driver. The amount of power assist is greatest at low speeds, for example when parking the car. At higher speeds, an electronic sensing system gradually reduces the level of power assist. In this way, the driver can control the car even more precisely than with conventional power steering. A number of automakers use Servotronic, including Audi, General Motors, BMW, Volkswagen, Volvo, SEAT and Porsche. Servotronic is a trademark of AM General Corp.[15]
Electric systems
Electric power steering (EPS or EPAS) uses an electric motor to assist the driver of a vehicle. Sensors detect the position and torque of the steering column, and a computer module applies assistive torque via the motor, which connects to either the steering gear or steering column. This allows varying amounts of assistance to be applied depending on driving conditions. Engineers can therefore tailor steering-gear response to variable-rate and variable-damping suspension systems, optimizing ride, handling, and steering for each vehicle.[16] On Fiat group cars the amount of assistance can be regulated using a button named "CITY" that switches between two different assist curves, while most other EPS systems have variable assist. These give more assistance as the vehicle slows down, and less at faster speeds. In the event of component failure that fails to provide assistance, a mechanical linkage such as a rack and pinion serves as a back-up in a manner similar to that of hydraulic systems.
Electric systems have an advantage in fuel efficiency because there is no belt-driven hydraulic pump constantly running, whether assistance is required or not, and this is a major reason for their introduction. Another major advantage is the elimination of a belt-driven engine accessory, and several high-pressure hydraulic hoses between the hydraulic pump, mounted on the engine, and the steering gear, mounted on the chassis. This greatly simplifies manufacturing and maintenance. By incorporating electronic stability control electric power steering systems can instantly vary torque assist levels to aid the driver in corrective maneuvers.[17]
The first electric power steering system appeared on the Suzuki Cervo in 1988. Today a number of manufacturers use electric power steering.
Electrically variable gear ratio systems
In 2000, Honda launched the S2000 Type V equipped with the world's first electric power variable gear ratio steering (VGS) system.[18][19] In 2003, Toyota introduced their own "Variable Gear Ratio Steering (VGRS)" system introduced on the Lexus LX 470 and Landcruiser Cygnus, and also incorporated the electronic stability control system to alter steering gear ratios and steering assist levels. In 2003, BMW introduced their "Active Steering" system on the 5-series.[20]
This system should not be confused with variable assist power steering, which varies steering assist torque, not steering ratios, nor with systems where the gear ratio is only varied as a function of steering angle. These last are more accurately called non-linear types; a plot of steering-wheel position versus axle steering angle is progressively curved (and symmetrical).
References
- ^ Popular Mechanics. Hearst Magazines. http://books.google.com/books?id=YuQDAAAAMBAJ&pg=PA59&dq=Invention+of+power+steering&hl=en&ei=yLleTpbkF8m1tgfS5fWlCw&sa=X&oi=book_result&ct=result&resnum=3&ved=0CDkQ6AEwAg#v=onepage&q&f=false.
- ^ "Driving-Gear For Motor Carriages". United States Patent and Trademark Office. http://www.google.com/patents?id=nYRCAAAAEBAJ&printsec=abstract#v=onepage&q&f=false.
- ^ Nunney, Malcolm James (2006). Light and Heavy Vehicle Technology. Elsevier Science. p. 521. ISBN 9780750680370. http://books.google.com/books?id=I90NpNQUzJ4C&pg=PA521&dq=Francis+W.+Davis+power+steering&hl=en&ei=ZdwbTKf6J4P6lweRmNXoCg&sa=X&oi=book_result&ct=result&resnum=5&ved=0CEEQ6AEwBA#v=onepage&q=Francis%20W.%20Davis%20power%20steering&f=false. Retrieved 18 June 2010.
- ^ Power Steering: The Pioneer Unit. Popular Science. http://books.google.com/books?id=xiwDAAAAMBAJ&pg=RA1-PA162&dq=Francis+W.+Davis+and+power+steering&hl=en&ei=Zos9ToX_NYSUtwef9sX-Ag&sa=X&oi=book_result&ct=result&resnum=3&ved=0CDYQ6AEwAg#v=onepage&q&f=false.
- ^ "The Waltham Museum’s Hall-of-Fame". Waltham Museumurl. http://www.walthammuseum.com/hof.htm.
- ^ a b Howe, Hartley E. (February 1956). "Mr. Power Steering's Ship Comes In". Popular Science 168 (2): 145–270. http://books.google.com/books?id=xiwDAAAAMBAJ&pg=RA1-PA162&dq=Francis+W.+Davis+power+steering&hl=en&ei=ZdwbTKf6J4P6lweRmNXoCg&sa=X&oi=book_result&ct=result&resnum=3&ved=0CDcQ6AEwAg#v=onepage&q=Francis%20W.%20Davis%20power%20steering&f=false. Retrieved 18 June 2010.
- ^ Lamm, Michael (March 1999). "75 years of Chryslers". Popular Mechanics 176 (3): 75. http://books.google.com/books?id=PmYEAAAAMBAJ&pg=PT34&dq=introduced+industry's+first+power+steering&hl=en&ei=WNkbTIWxL8GAlAejrIWRDg&sa=X&oi=book_result&ct=result&resnum=3&ved=0CDsQ6AEwAg#v=onepage&q=introduced%20industry's%20first%20power%20steering&f=false. Retrieved 18 June 2010.
- ^ Watson, Bill (22 March 2006). "History of Power Steering". Imperial Automobile Club Archives. http://archivesearch.imperialclub.com/archives/msg111055.html. Retrieved 18 June 2010.
- ^ "MANUAL AND POWER ACTUATED STEERING MECHANISM FOR MOTOR VEHICLES". Canadian Intellectual Property Office. http://brevets-patents.ic.gc.ca/opic-cipo/cpd/eng/patent/566405/summary.html?query=Charles+F.+Hammond&start=1&num=50&type=basic_search.
- ^ "MANUAL AND POWER ACTUATED STEERING GEAR". Canadian Intellectual Property Office. http://brevets-patents.ic.gc.ca/opic-cipo/cpd/eng/patent/561370/summary.html?query=Charles+F.+Hammond&start=1&num=50&type=basic_search.
- ^ "MANUAL AND POWER ACTUATED STEERING MECHANISM FOR MOTOR VEHICLES". Canadian Intellectual Property Office. http://brevets-patents.ic.gc.ca/opic-cipo/cpd/eng/patent/554310/summary.html?query=Charles+F.+Hammond&start=1&num=50&type=basic_search.
- ^ "Will a twist of your wrist steer your next car?". Popular Science 186 (4): 83. February 1984. http://books.google.com/books?id=GuMDAAAAMBAJ&pg=PA82&dq=first+%22electric+power+steering%22&lr=&ei=q1ZbS7qmGJuQywTRzsSnBA&client=safari&cd=25#v=onepage&q=&f=false. Retrieved 2010–01–23.
- ^ Markovich, Alex (April 1965). "Look, Ma-No Wheels". Popular Mechanics 123 (4): 91–93. http://books.google.com/books?id=A-MDAAAAMBAJ&pg=PA91&dq=Mercury+twist+wrist+steering&lr=&ei=P11bS4fnDKDiyQSFiaSMCA&client=safari&cd=14#v=onepage&q=Mercury%20twist%20wrist%20steering&f=false. Retrieved 2010–01–23.
- ^ "The Golf Ecomatic Page". Deylan.co.uk. http://www.deylan.co.uk/golf/ecomatic/index.htm. Retrieved 2010-12-14.
- ^ Audi of America Usage Agreement
- ^ Keebler, Jack (May 1986). "So long, hydraulics - the electronic revolution in power steering". Popular Science 228 (5): 50–56. http://books.google.com/books?id=07B8zK-PQq8C&pg=PA52&dq=%22electric+power+steering%22&lr=&ei=UlNbS4nkK4iUyATek62vCQ&client=safari&cd=11#v=onepage&q=%22electric%20power%20steering%22&f=false. Retrieved 2010–01–23.
- ^ "Electric power steering: one good turn deserves another". Eetimes.com. http://www.eetimes.com/design/embedded/4006457/Electric-power-steering-one-good-turn-deserves-another. Retrieved 2011-09-07.
- ^ "Honda Worldwide | World News | News Release | July 7, 2000". World.honda.com. http://world.honda.com/news/2000/4000707.html. Retrieved 2009-12-08.
- ^ "What's New: Honda's Revolutionary New Steering System". Honda.co.nz. http://www.honda.co.nz/site/news/items/2000_sep.html. Retrieved 2009-12-08.[dead link]
- ^ "BMW » First Drive: 2004 BMW 5-Series". CanadianDriver. 2003-06-02. http://www.canadiandriver.com/2003/06/02/first-drive-2004-bmw-5-series.htm. Retrieved 2009-12-08.
External links
Manufacturers:
- Nexteer Automotive
- Danaher Motion
- JTEKT
- ThyssenKrupp Presta Steering, Eschen, Liechtenstein
- TRW Automotive
- ZF Friedrichshafen
Categories:- Automotive steering technologies
- Auto parts
- Automotive accessories
Wikimedia Foundation. 2010.