Magnetotelluric station

Magnetotellurics (MT) is an electromagnetic geophysical method of imaging the earth's subsurface by measuring natural variations of electrical and magnetic fields at the Earth's surface. Investigation depth ranges from 300m below ground by recording higher frequencies down to 10,000m or deeper with long-period soundings. Developed in Russia and France during the 1950s, MT is now an international academic discipline and is used in exploration surveys around the world. Commercial uses include hydrocarbon (oil and gas) exploration, geothermal exploration, mining exploration, as well as hydrocarbon and groundwater monitoring. Research applications include experimentation to further develop the MT technique, long-period deep crustal exploration, and earthquake precursor prediction research.



Andrey Tikhonov, one of the creators of magentotellurics

The magentotelluric technique was introduced by the French geophysicist Louis Cagniard[1] and Russian geophysicist Andrey Nikolayevich Tikhonov in the early 1950s. With advances in instrumentation, processing and modeling, MT has become one of the most important tools in deep Earth research.

Since the 1950s sensors, receivers and data processing techniques have followed the general trends in digital electronics, becoming less expensive and more capable with each generation. Major advances in MT instrumentation and technique include the advent of remote referencing, GPS time-based synchronization, and 3D data acquisition and processing.

Commercial applications

Hydrocarbon exploration

For hydrocarbon exploration, MT is mainly used as a complement to the primary technique of reflection seismology exploration.[2][3][4][5] While seismic imaging is able to image subsurface structure, it cannot detect the changes in resistivity associated with hydrocarbons and hydrocarbon-bearing formations. MT does detect resistivity variations in subsurface structures, which can differentiate between structures bearing hydrocarbons and those that do not.[6]

At a basic level of interpretation, resistivity is correlated with different rock types. High-velocity layers are typically highly resistive, whereas sediments – porous and permeable – are typically much less resistive. While high-velocity layers are an acoustic barrier and make seismic ineffective, their electrical resistivity means the magnetic signal passes through almost unimpeded. This allows MT to see deep beneath these acoustic barrier layers, complimenting the seismic data and assisting interpretation.[7] 3-D MT survey results in Uzbekistan (32 x 32 grid of soundings) have guided further seismic mapping of a large known gas-bearing formation with complex subsurface geology.[8][9]

China National Petroleum Corporation (CNPC) uses onshore MT more than any other oil company in the world, conducting thousands of MT soundings for hydrocarbon exploration and mapping throughout all of China.[10]

Mining exploration

MT is used for various base metals (nickel and precious metals exploration, as well as for kimberlite) mapping.

INCO's 1991 proof-of-concept study in Sudbury, Ontario, Canada sensed a 1750 meter-deep nickel deposit. Falconbridge followed with a feasibility study in 1996 that accurately located two Ni-Cu mineralized zones at ~800 m and ~1350 m. Since then, both major and junior mining companies are increasingly using MT and AMT for both brownfields and greenfields exploration. Significant MT mapping work has been done on areas of the Canadian Shield.[11]

Diamond exploration, by detecting kimberlites, is also a proven application.[12]

Geothermal exploration

MT geothermal exploration measurements allow detection of resistivity anomalies associated with productive geothermal structures, including faults and the presence of a cap rock, and allow for estimation of geothermal reservoir temperatures at various depths.[13][14][15] Dozens of MT geothermal exploration surveys have been completed in Japan and the Philippines since the early 1980s, helping to identify several hundred megawatts of renewable power at places such as the Hatchobaru plant on Kyushu[16][17] and the Togonang plant on Leyte.[18][19][20] Geothermal exploration with MT has also been done in the United States, Iceland, New Zealand, Hungary,[14] China,[21] Ethiopia, Indonesia, Peru,[22] Australia, and India.[23]

Other commercial applications

MT is also used for groundwater exploration and mapping, hydrocarbon reservoir monitoring, deep investigation (100 km) of the electrical properties of the bedrock for high-voltage direct current (HVDC) transmission systems,[24] carbon dioxide sequestration,[25][26] and other environmental engineering applications (e.g. nuclear blast site monitoring[27] and nuclear waste disposal site monitoring).

Research applications

Crustal research

MT has been used to investigate the distribution of silicate melts in the Earth's mantle and crust; large investigations have focused on the East Pacific Rise and the Tibetan Plateau. Other research work aims to better understand the plate-tectonic processes in the highly complex three-dimensional region formed by the collision of the African and European plates.[28]

Earthquake precursor prediction research

Fluctuations in the MT signal may be able to predict the onset of seismic events.[29][30][31] Stationary MT monitoring systems have been installed in Japan since April 1996, providing a continuous recording of MT signals at the Wakuya Station (previously at the Mizusawa Geodetic Observatory) and the Esashi Station of the Geographical Survey Institute of Japan. These stations measure fluctuations in the Earth's electromagnetic field that correspond with seismic activity.[32] The raw geophysical time-series data from these monitoring stations is freely available to the scientific community, enabling further study of the interaction between EM events and earthquake activity. The MT time series data from the GSIJ earthquake monitoring stations is available online at

Additional MT earthquake precursor monitoring stations in Japan are located in Kagoshima, in Sawauchi, and on Shikoku. Similar stations are also deployed in Taiwan on Penghu Island, as well as in the Fushan Reserve on the island of Taiwan proper.[33]

POLARIS is a Canadian research program investigating the structure and dynamics of the Earth's lithosphere and the prediction of earthquake ground motion.[34]

Theory and practice

Energy sources

Solar energy and lightning cause natural variations in the earth's magnetic field, inducing electric currents (known as telluric currents) under the Earth's surface. Simultaneous measurements of orthogonal components of the electric and magnetic fields are recorded, with the results calculated as the impedance tensor.[35] A subsurface resistivity model is then created using this tensor.[36]

Different rocks, sediments and geological structures have a wide range of different electrical conductivities. Measuring electrical resistivity allows different materials and structures to be distinguished from one another and can improve knowledge of tectonic processes and geologic structures.

The Earth's naturally varying electric and magnetic fields are measured over a wide range of magnetotelluric frequencies from 10,000 Hz to 0.0001 Hz (10,000s). These fields are due to electric currents flowing in the Earth and the magnetic fields that induce these currents. The magnetic fields are produced mainly by the interaction between the solar wind and the magnetosphere. In addition, worldwide thunderstorm activity causes magnetic fields at frequencies above 1 Hz. Combined, these natural phenomena create strong MT source signals over the entire frequency spectrum.

The ratio of the electric field to magnetic field provides simple information about subsurface conductivity. Because the skin effect phenomenon affects the electromagnetic fields, the ratio at higher frequency ranges gives information on the shallow Earth, whereas deeper information is provided by the low-frequency range. The ratio is usually represented as both apparent resistivity as a function of frequency and phase as a function of frequency.

Depth and resolution

MT measurements can investigate depths from about 300m down to tens of kilometres, though investigations in the range of 500m to 10,000m are typical. Greater depth requires measuring lower frequencies, which in turn requires longer recording times. Very deep, very long-period measurements (15km or more), may require recordings of several days to obtain satisfactory data quality.

Horizontal resolution of MT mainly depends on the distance between sounding locations- closer sounding locations increase the horizontal resolution. Continuous profiling (known as dipole-to-dipole) has been used, with only metres between the edges of each telluric dipole.

Vertical resolution of MT mainly depends on the frequency being measured, as lower frequencies have longer wavelengths. Accordingly, vertical resolution decreases as depth of investigation increases.

Signal strength and recording times

Magnetic fields in the frequency range of 1 Hz to approximately 20 kHz are part of the audio-magnetotelluric (AMT) range. These are parallel to the Earth surface and move towards the Earth's centre. This large frequency band allows for a range of depth penetration from several metres to several kilometres below the Earth's surface. Due to the nature of magnetotelluric source, the waves generally fluctuate in amplitude height. Long recording times are needed to ascertain usable reading due to the fluctuations and the low signal strength. Generally, the signal is weak between 1 to 5 kHz, which is a crucial range in detecting the top 100m of geology. The magnetotelluric method is also used in marine environments for hydrocarbon exploration and lithospheric studies.[37] Due to the screening effect of the electrically conductive sea water, a usable upper limit of the spectrum is around 1 Hz.

2D and 3D Magnetotellurics

Two-dimensional surveys consist of a longitudinal profile of MT soundings over the area of interest, providing two-dimensional "slices" of subsurface resistivity.

Three-dimensional surveys consist of a loose grid pattern of MT soundings over the area of interest, providing a more sophisticated three-dimensional model of subsurface resistivity.


Audio-magnetotellurics (AMT)

AMT is a higher-frequency magnetotelluric technique for shallower investigations. While AMT has less depth penetration than MT, AMT measurements often take only about one hour to perform (but deep AMT measurements during low-signal strength periods may take up to 24 hours) and use smaller and lighter magnetic sensors. Transient AMT is an AMT variant that records only temporarily during periods of more intense natural signal (transient impulses), improving signal-to-noise-ratio at the expense of strong linear polarization.[38]

Controlled source electromagnetics

CSEM Controlled source electro-magnetic is a deep-water offshore variant of controlled source audio magnetotellurics– CSEM is the named used in the offshore oil and gas industry.[39]

Onshore CSEM / CSAMT may be effective where electromagnetic cultural noise (e.g. power lines, electric fences) present interference problems for natural-source geophysical methods. An extensive grounded wire (2 km or more) has currents at a range of frequencies (0.1 Hz to 100 kHz) passed through it. The electric field parallel to the source and the magnetic field which is at right angles are measured. The resistivity is then calculated, and the lower the resistivity, the more likely there is a conductive target (graphite, nickel ore or iron ore). CSAMT is also known in the oil and gas industry as Onshore Controlled Source ElectroMagnetics (Onshore CSEM).

An offshore variant of MT, MMT uses instruments and sensors in pressure housings deployed by ship into shallow coastal areas where water is less than 300m deep.[40][41][42][43][4] A derivative of MMT is offshore single-channel measurement of the vertical magnetic field only (the Hz, or "tipper"), which eliminates the need for telluric measurements and horizontal magnetic measurements.[44] While the theory is sound, no commercial system is yet available. Furthermore, any such system would require a solution providing for the precise orientation and stabilization of the magnetic sensor.[45]

Exploration surveys

MT exploration surveys are done to acquire resistivity data which can be interpreted to create a model of the subsurface. Data is acquired at each sounding location for a period of time (overnight soundings are common), with physical spacing between soundings dependant on the target size and geometry, local terrain constraints and financial cost. Reconnaissance surveys can have spacings of several kilometres, while more detailed work can have 200m spacings, or even adjacent soundings (dipole-to-dipole). MT surveys are carried out year-round in the Americas, Europe, Asia, Africa and Oceania.

The HSE impact of MT exploration is relatively low because of light-weight equipment, natural signal sources, and reduced hazards compared to other types of exploration (e.g. no drills, no explosives, and no high currents).

Remote reference soundings

Remote Reference is an MT technique used to account for cultural electrical noise by acquiring simultaneous data at more than one MT station. This greatly improves data quality, and may allow acquisition in areas where the natural MT signal is difficult to detect because of man-made EM interference.

Survey equipment

A typical full suite of MT equipment (for a "five component" sounding) consists of a receiver instrument with five sensors: three magnetic sensors, and two telluric (electric) sensors. In many situations, only the telluric sensors will be used, and magnetic data borrowed from other nearby soundings to reduce acquisition costs.

A complete five-component set of MT equipment can be backpack-carried by a small field team (3 to 4 persons) or carried by a light helicopter (such as the MD Helicopters MD 500), allowing deployment in remote and rugged areas. Most MT equipment is capable of reliable operation over a wide range of environmental conditions, with ratings of typically −20C to +45C, from dry desert to high-humidity (condensing) and partial immersion.

Data processing and interpretation

Post-acquisition processing is required to transform raw time-series data into frequency-based inversions. The resulting output of the processing program is used as the input for subsequent interpretation. Processing may include the use of remote reference data or local data only.

Processed MT data is modelled using various techniques to create a subsurface resistivity map, with lower frequencies generally corresponding to greater depth below ground. Anomalies such as faults, hydrocarbons, and conductive mineralization appear as areas of higher or lower resistivity from surrounding structures.

Instrument and sensor manufacturers

MT instrumentation design and construction is a specialized international activity, with only a small number of companies and scientific organizations having the necessary expertise and technology. Three companies supply most of the commercial-use world market: one in the United States (Zonge Engineering and Research Organization, Inc.],[46] one in Canada (Phoenix Geophysics, Ltd.)[47] and one in Germany (Metronix Messgeraete und Elektronik GmbH). Government agencies and smaller companies producing MT instrumentation for internal use include Vega Geophysics, Ltd. in Russia and the Russian Academy of Sciences (SPbF IZMIRAN); and the National Space Research Institute of Ukraine.

See also


  1. ^ Cagniard, L. (1953) Basic theory of the magneto-telluric method of geophysical prospecting, Geophysics, 18, 605–635
  2. ^ [1][dead link]
  3. ^
  4. ^ a b
  5. ^ "Microsoft Word – MT_for_Oil _and_Gas_Exploration_2008_FINAL_10.17.08" (PDF). Retrieved 18 October 2011. 
  6. ^ "Oil and Gas exploration". Retrieved 18 October 2011. 
  7. ^ "CSIRO PUBLISHING – Exploration Geophysics". Retrieved 18 October 2011. 
  8. ^ "3-D MT SURVEY IN UZBEKISTAN". Retrieved 18 October 2011. 
  9. ^ "CSIRO PUBLISHING – ASEG Extended Abstracts". Retrieved 18 October 2011. 
  10. ^ "SYSTEM 2000 FUELS EXPLORATION BOOM". Retrieved 18 October 2011. 
  11. ^
  12. ^ "Imaging the geometry and structure of kimberlite pipes using audio-MT". Retrieved 18 October 2011. 
  13. ^ "Microsoft Word – MT_for_Geothermal_Exploration_2008_FINAL_10.17.08" (PDF). Retrieved 18 October 2011. 
  14. ^ a b
  15. ^ "Characterizing a geothermal reservoir using broadband 2D MT survey in Theistareykir, Iceland" (PDF). Retrieved 18 October 2011. 
  16. ^ "IGA International Geothermal Association".,welcome_to_our_page_with_data_for_japan.html. Retrieved 18 October 2011. 
  17. ^ "Science Links Japan | Geothermal Reservoirs Modeling in the Western Side of Mt. Aso, SW Japan by Magnetotelluric Method". 18 March 2009. Retrieved 18 October 2011. 
  18. ^ "IGA International Geothermal Association".,welcome_to_our_page_with_data_for_philippines.html. Retrieved 18 October 2011. 
  19. ^ "Philippine National Oil Company". Retrieved 18 October 2011. 
  20. ^ "Geothermal | The Energy Development Corporation Website". Retrieved 18 October 2011. 
  21. ^
  22. ^ "Geothermal Mt Survey In Peru". Retrieved 18 October 2011. 
  23. ^ "An analysis of magnetotelluric (MT) data over geothermal region of Bakreshwar, West Bengal". Retrieved 18 October 2011. 
  24. ^
  25. ^ "Energy Sector: Science and Technology: Cleaner Fossil Fuels". 4 May 2010. Retrieved 18 October 2011. 
  27. ^ "Hydrogeologic assessment of the Amchitka Island nuclear test site (Alaska) with magnetotellurics". Retrieved 18 October 2011. 
  28. ^
  29. ^ "Terrestrial, Atmospheric and Oceanic Sciences". 21 September 1999. Retrieved 18 October 2011. 
  30. ^ "Seiya Uyeda, et. al., ''Short-term earthquake prediction: Current status of seismo-electromagnetics,'' Tectonophysics, Volume 470, Issues 3–4, 29 May 2009, Pages 205–213 Abstract on ScienceDirect". Retrieved 18 October 2011. 
  31. ^
  32. ^
  33. ^
  34. ^ "Polaris Consortium". Retrieved 18 October 2011. 
  35. ^ Cantwell, T. (1960) Detection and Analysis of Low-Frequency Magnetotelluric Signals, PhD Thesis, Massachusetts Institute of Technology, Cambridge, Massachusetts
  36. ^ "Basic Theory Of The Magneto-Telluric Method Of Geophysical Prospecting". Retrieved 18 October 2011. 
  37. ^ "Welcome to the Scripps Institution of Oceanography Marine EM Laboratory website". 23 April 2010. Retrieved 18 October 2011. 
  38. ^ "EMpulse Geophysics – Saskatoon". Retrieved 18 October 2011. 
  39. ^ "Scripps Institution of Oceanography Marine EM Laboratory | Research | Concepts |CSEM and MT Exploration for Petroleum". 6 May 2009. Retrieved 18 October 2011. 
  40. ^
  41. ^ "Gemini Prospect Marine MT and CSEM Surveys". 6 May 2009. Retrieved 18 October 2011. 
  42. ^ "Marine Mt In China With Phoenix Equipment". Retrieved 18 October 2011. 
  43. ^ "Integrated Electromagnetic Services, WesternGeco". Retrieved 18 October 2011. 
  45. ^ <
  46. ^ "Surveys | AMT and MT". Zonge. Retrieved 18 October 2011. 
  47. ^ "Phoenix products : the MTU Receiver". Retrieved 18 October 2011. 

External links

Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • magnetotellurics — noun A natural source, electromagnetic geophysical method of imaging structures below the earths surface …   Wiktionary

  • Magnetometer — A magnetometer is a measuring instrument used to measure the strength or direction of a magnetic field either produced in the laboratory or existing in nature. Some countries such as the USA, Canada and Australia classify the more sensitive… …   Wikipedia

  • Telluric current — A telluric current (from Latin tellūs , earth ) is an electric current which moves underground or through the sea. Telluric currents result from both natural causes and human activity, and the discrete currents interact in a complex pattern. The… …   Wikipedia

  • List of Russian people — The Millennium of Russia monument in Veliky Novgorod, featuring the statues and reliefs of the most celebrated people in the first 1000 years of Russian history …   Wikipedia

  • Lightning — This article is about the atmospheric electrical phenomenon. For other uses, see Lightning (disambiguation). See also: Lightning strike Lightning striking Atlanta, United States Lightning is an atmospheric electrostatic discharge (spar …   Wikipedia

  • Earth's magnetic field — Computer simulation of the Earth s field in a normal period between reversals.[1] The tubes represent magnetic field lines, blue when the field points towards the center and yellow when away. The rotation axis of the Earth is centered and… …   Wikipedia

  • Geomagnetic storm — This article is about disturbances within Earth s magnetosphere. For other uses of magnetic storm , see Magnetic storm (disambiguation). Solar particles interact with Earth s magnetosphere. A geomagnetic storm is a temporary disturbance of the… …   Wikipedia

  • MT — MT, Mt, mT, mt, or Mt. may stand for: Contents 1 Automotive 2 Computing and the Internet 3 Geography and languages 4 Media and entertainment …   Wikipedia

  • Taupo Volcanic Zone — The Taupo Volcanic Zone is a highly active volcanic area in the North Island of New Zealand. It is named after Lake Taupo, the flooded caldera of the largest volcano in the zone. ActivityThere are numerous volcanic vents and geothermal fields in… …   Wikipedia

  • St. Elmo's fire — For other uses, see St. Elmo s fire (disambiguation). St. Elmo s fire on a ship at sea St. Elmo s fire (also St. Elmo s light[1][2]) is a weather phenomenon …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”