Clinker (boat building)

Clinker (boat building)
A Viking longship, displaying the overlapping planks that characterize clinker construction.

Clinker building is a method of constructing hulls of boats and ships by fixing wooden planks and, in the early nineteenth century, iron plates to each other so that the planks overlap along their edges. The overlapping joint is called a land. In any but a very small boat, the individual planks will also be joined end to end; the whole length of one of these composite planks is a strake. The technique developed in northern Europe and was successfully used by the Vikings and typical for the Hanseatic cog. The construction method is known in some places as lapstrake.[1]

Examples of clinker-built boats, and which are directly descended from those of the Viking shipbuilders, are the traditional round-bottomed Thames skiffs, built of mahogany, which can still be seen on the River Thames in England, and the larger, (originally) cargo-carrying Norfolk wherries.[2]

Contents

Origin

The technique of clinker developed in the Nordic (Germanic) shipbuilding tradition as distinct from the Mediterranean mortise and tenon planking technique which was introduced to the provinces of the north in the wake of Roman expansion. Overlapping seams already appear in the 4th century BC Hjortspring boat. The oldest evidence for a clinker-built vessel, dendrochronologically dated to 190 AD, are boat fragments which were found in recent excavations at the site of the famous Nydam Boat.[3] The Nydam Boat itself, built ca. 320 AD, is the oldest preserved clinker-built boat.[4] Clinker-built ships were a trademark of Nordic navigation throughout the Middle Ages, particularly of the longships of the Viking explorers and the trading cogs of the Hanseatic League.

Building a dinghy

Since the ninth century, perhaps culminating in the nineteenth, many ships were clinker-built. Although it was developed primarily for use on wooden ships, some later iron ships also used this method. To give an understanding of what it involved, the best course is to describe the building of a pulling dinghy (a rowboat). The reader should allow for the added complexity which comes from larger size.

Planking

A comparison of clinker-building and carvel-building styles.

In building a simple pulling boat, the keel, hog, stem, apron, deadwoods, sternpost and perhaps transom are assembled and securely set up. In normal practice, this will be the same way up as they will be in use. From the hog, the garboard, bottom, bilge, topside and sheer strakes are planked up, held together along their lands by copper rivets. At the stem and in a double-ended boat, the sternpost, geralds are formed. That is, in each case, the land of the lower strake is tapered to a feather edge at the end of the strake where it meets the stem or stern-post. This allows the end of the strake to be screwed to the apron with the outside of the planking mutually flush at that point and flush with the stem. This means that the boat's passage through the water will not tend to lift the ends of the planking away from the stem. Before the next plank is laid up, the face of the land on the lower strake is bevelled to suit the angle at which the next strake will lie in relation with it. This varies all along the land. Gripes are used to hold the new strake in position on the preceding one before the fastening is done.

Timbering or framing out

Once the shell of planking is assembled, transverse battens of oak, ash or elm, called timbers are steam-bent to fit the internal, concave side. The timbers are frequently miscalled ribs. Elm species are not durable where the boat is used frequently in fresh water. As the timbers are bent in, they are copper riveted to the shell, through the lands of the planking.

On many clinker built craft, e.g. in Scandinavia, in Thames skiffs, and larger working craft like the coble, sawn frames are used, assembled from floors and top timbers, joggled to fit the lands. Sometimes the timbers in larger craft were also joggled before being steamed in.

With the timbers all fitted, longitudinal members are bent in. The thwart risings are fastened through the timbers with its upper edge on the level of the undersides of the thwarts. Bilge keels are added to the outside of the land on which the boat would lie on a hard surface to stiffen it and protect it from wear. A stringer is usually fitted round the inside of each bilge to strengthen it. In a small boat, this is usually arranged to serve also as a means of retaining the bottom boards. These are removable assemblies, shaped to lie over the bottom timbers and be walked upon. They spread the stresses from the crew's weight across the bottom structure.

Longitudinals

Inboard of the sheer strake the heavier gunwale is similarly bent in along the line of the sheer. This part of the work is finished by fitting the breast hook and quarter knees. Swivel or crutch chocks are fitted as appropriate to the gunwale, the thwarts fitted down onto the rising and held in position by knees up to the gunwale and perhaps down onto the stringer. The structure of gunwale, rising, thwart and thwart knees greatly stiffens and strengthens the shell and turns it into a boat. There are several ways of fixing the rubbing strake but in a clinker boat, it is applied to the outside of the sheer strake.

Fittings

Finally, the fittings such as swivels or crutch plate, painter ring, stretchers, keel and stem band are fitted and fixed with screws. In a sailing dinghy, there would be more fittings such as fairleads, horse, shroud plates, mast step, toe straps and so on.

Finishing

That more or less finishes the boatbuilder's work but the painter has yet to varnish or paint it. At stages along the way, he will have been called in to prime the timber. This is particularly so immediately before the timbering is done. The boatbuilder will clean up the inside of the planking and the painter will prime it and probably more, partly because it is easier that way and partly so as to put some preservative on the planking behind the timbers. Similarly, it is best to have the varnishing done after the fittings are fitted but before they are shipped. Thus, the keel band will be shaped and drilled and the screw holes drilled in the wood of keel and stem then the band will be put aside while the varnishing is done.

Fastenings

The planks may be fastened together in several ways:

  • with copper or iron rivets consisting of a square nail and a dish shaped washer called a rove. The land is pierced, the nail knocked through from the outside, the rove punched on while the head is held up by a dolly. The nail is cut off just proud of the rove and the cut end clenched[5] over the rove while the dolly (a small portable anvil, usually of cylindrical shape) is used to hold the nail in place. In planking up clinker work, one man can hold both dolly and clenching hammer. Although this is common where sawn frames are to be used, boats intended for steamed timbers are usually nailed but not clenched until the timbering out is complete. As timbering is a two handed job it is more efficient to leave the clenching until help is at hand then the helper dollies up, whilst the builder sits inside the hull and clenches up.
  • with iron nails with the pointed nail ends protruding on the inside of the boat, bent over and back into the wood in the form of a hook. This is a cheap and cheerful technique maybe called clinching in some parts but usually, in England at least, "turnin'-em-over". It is the sort of thing which used to be found in Scandinavian-built boats but even with iron nails, on the lands, they were usually properly clenched over roves. Nails fastening timbers were sometimes turned over, particularly where removable bottom boards were to rest on the timbers. However, it was possible to tread the bottom boards onto the clenched nails and where marks were left, gouge out recesses to accommodate the clenched nails.
  • screws were used for fixing the ends of the strakes to apron and transom and in later times, knees to gunwale and thwarts, but traditionally, this last would be done with a clench bolt or a large copper nail, clenched.
  • adhesive, notably epoxy. Traditionally, lands were neither glued nor was anything used to bed them. The garboard was bedded onto the hog and keel, and the ends of the strakes onto the stem and apron using a mixture of white lead and grease. During the World Wars new techniques and materials were developed by the aircraft industry. By the mid 1950s, these were well infiltrated into the boatbuilding trade. New boats in classes of racing dinghy with clinker hulls were built as glued clinker boats. The basic construction was the same but ply planking was used and the lands were glued with no fastenings, except that the ends and garboards were still screwed to apron and hog. The need to prevent the splitting of the planks was removed by the use of ply so no timbers were used. Except for a light gunwale and wide rubbing strake, the longitudinals were omitted too. A short thwart rising and knees were glued to the planking. These boats were all decked and that is how adequate stiffness was achieved. So that the liquid glue could be laid onto the land before the next plank was assembled onto it, they were built upside down.

Fastening the centre-line structure

In the last few years of wooden boat construction, glue and screws took over, but until the 1950s, the keel, hog, stem, apron, deadwoods, sternpost, and perhaps transom would be fastened together by bolts set in white lead and grease. There are three kinds of bolt, of which, nowadays, the screw bolt, with its nut and washer, is by far the most common. The second type of bolt is the pin bolt or cotter bolt, which, instead of a thread, has a tapered hole forged through the end away from the head, into which a tapered pin or cotter is knocked. The taper is in effect a straight thread. In conjunction with a washer, this draws the bolt tight, as a nut does on a screw bolt. The third type of bolt is the clench bolt. It has some of the features of a rivet but was usually much longer than the normal rivet; in a wooden ship, perhaps a metre or more. For a shipwright's use, it is of copper. A head is formed by clenching it over a washer in a swage plate. It is then knocked through a hole bored through the work to be fastened. The head is held up with a dolly and the other end is formed in the same way as the head but without the swage plate. Until well into the nineteenth century, this is what held the great ships of the world together, though some may have used iron. Until the late 1950s, the centre-line assembly of British Admiralty twenty-five foot motor cutters were fastened this way.

Where suitable metal was not available, it was possible to use treenails (pronounced trennels). They were like clench bolts but made of wood, and instead of being clenched, they had a hardwood wedge knocked into each end to spread it. The surplus was then sawn off.

Relationship between clinker and carvel

The Clinker form of construction is linked in people's minds with the Vikings who used this method to build their famous longships from riven timber (split wood) planks. Clinker is the British term, which is also used in Canada and most other countries of the world except the USA, where the method is known as lapstrake.

Carvel construction was probably invented earlier than clinker but in other parts of the world. In Europe carvel was the method of the south probably having spread though the Mediterranean from the Middle East. Clinker was the method of north Europe having developed, apparently, in the Baltic.

The smoother surface of a carvel boat gives the impression at first sight that it is hydrodynamically more efficient. The lands of the planking are not there to disturb the stream line. This distribution of relative efficiency between the two forms of construction is an illusion because for given hull strength, the clinker boat is lighter because it does not rely upon the compressive forces of the caulking and the resulting friction to bind the skin together. It therefore displaces less water so it has less to push aside while moving. The reduced displacement could be used to make the lines finer so as to make the passage through the water easier still. Of course, displacement was increased as cargo was loaded but still, the clinker vessel had the advantage in efficiency as the structure can be less bulky. Therefore, for a given internal volume, there was a smaller external one, meaning that a bulkier cargo could be carried if need be, given sufficient freeboard.[citation needed]

Additionally, the clinker built method as used by the Vikings created a vessel which could twist and flex relative to the line extending length of the vessel, bow to stern. This gave it an advantage in North Atlantic rollers so long as the vessel was small in overall displacement. Increasing the beam, due to the light nature of the method, did not commensurately increase the vessel's survivability under the torsional forces of rolling waves, and greater beam widths may have made the resultant vessels more vulnerable.

There is an upper limit to the size of clinker built vessels, which could be and was exceeded by several orders of magnitude in later large sailing vessels incorporating carvel-built construction. Clinker requires relatively wide planking stock compared to carvel, as carvel can employ stealers to reduce plank widths amidships where the girth is greatest. The need for sufficient lap to accept the clench fastenings drives towards wider planks in proportion to thickness that can be employed in carvel. In all other areas of construction including framing, deck, etc., clinker is as capable as carvel. Clinker construction remains to this day a valuable method of construction for small wooden vessels.

See also

References

  1. ^ Clinker Boat History & Building(Michael Webb)
  2. ^ Clinker Boat Building (Hobby.net.au Australia)
  3. ^ Jorgensen et al. 2003 p299, The Spoils of Victory – the north in the shadow of the Roman Empire, Nationalmuseet
  4. ^ The Nydam Boats
  5. ^ Some people would pronounce this word as "clinched" but there always was room for regional variation in boatbuilding words.

Other sources

  • Greenhill, Basil (1976) Archaeology of the Boat (London: Adam and Charles Black Publishers Ltd) ISBN 978-0713616453
  • Greenhill, Basil, Morrison, John S. (1995) The Archaeology of Boats & Ships – An Introduction (London: Conway Maritime Press) ISBN 978-1557500397
  • McKee, Eric (1972) Clenched Lap or Clinker: An Appreciation of a Boatbuilding Technique (Greenwich: National Maritime Museum)
  • Leather, John (1990) Clinker Boatbuilding (Adlard Coles) ISBN 978-0713636437

Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Boat building — Boat building, one of the oldest branches of engineering, is concerned with constructing the hulls of boats and, for sailboats, the masts, spars and rigging.Parts* Bow the front and generally sharp end of the hull. It is designed to reduce the… …   Wikipedia

  • Carvel (boat building) — In boat building, carvel built or carvel planking is a method of constructing wooden boats and tall ships by fixing planks to a frame so that the planks butt up against each other, edge to edge, gaining support from the frame and forming a smooth …   Wikipedia

  • Clinker — may refer to: Clinker (boat building), construction method for wooden boats Clinker (waste), waste from industrial processes Clinker (cement), a kilned then quenched cement product Clinker brick, rough dark coloured bricks Clinker Peak, a… …   Wikipedia

  • Boat Encampment — was a rendezvous and staging point for the Hudson s Bay Company in the early 19th Century and later a locality by that name in the Canadian province of British Columbia. It was located at the top of the Big Bend of the Columbia north of the city… …   Wikipedia

  • Newcastle University Boat Club — Coordinates: 54°58′47″N 1°44′37″W / 54.9798°N 1.7436°W / 54.9798; 1.7436 …   Wikipedia

  • Sewn boat — A sewn boat is a type of wooden boat or ship which is clinker built and held together with tendons or flexible wood, such as roots and willow branches. Sewn boat construction techniques were used in many parts of the world prior to the… …   Wikipedia

  • Punt (boat) — This article concentrates on the history and development of punts and punting in England, for other usages see Norfolk punt and the general disambiguation pages at punt and punter. A punt is a flat bottomed boat with a square cut bow, designed… …   Wikipedia

  • Dolly (tool) — A dolly is the name given to a category of tools used in shaping sheet metal. In general, a dolly is a solid piece of metal, small enough to hold in one hand, with a curved or shaped face. Generally a dolly will have more than one surface, each… …   Wikipedia

  • Clapboard (architecture) — A New England saltbox house with unpainted clapboard siding Clapboard, also known as bevel siding or lap siding or weather board (with regional variants as to the exact definitions of these terms), is a board used typically for exterior… …   Wikipedia

  • Scottish east coast fishery — The Scottish east coast fishery has been in existence for more than a thousand years, spanning the Viking period right up to the present day. A brief historyThe fishery has always been for both whitefish and herring. The Norsemen came to Scotland …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”