DIAC

"DIAC" redirects here. For other uses, see DIAC (disambiguation).

Typical DIAC voltage and current relationships. V_BO - breakover voltage

DIAC

Three-layer DIAC

The DIAC, or 'diode for alternating current', is a diode that conducts current only after its breakover voltage has been reached momentarily.

When this occurs, diode enters the region of negative dynamic resistance, leading to a decrease in the voltage drop across the diode and, usually, a sharp increase in current through the diode. The diode remains "in conduction" until the current through it drops below a value characteristic for the device, called the holding current. Below this value, the diode switches back to its high-resistance (non-conducting) state. This behavior is bidirectional, meaning typically the same for both directions of current.

Most DIACs have a three-layer structure with breakover voltage around 30 V. In this way, their behavior is somewhat similar to (but much more precisely controlled and taking place at lower voltages than) a neon lamp.

DIACs have no gate electrode, unlike some other thyristors that they are commonly used to trigger, such as TRIACs. Some TRIACs, like Quadrac, contain a built-in DIAC in series with the TRIAC's "gate" terminal for this purpose.

DIACs are also called symmetrical trigger diodes due to the symmetry of their characteristic curve. Because DIACs are bidirectional devices, their terminals are not labeled as anode and cathode but as A1 and A2 or MT1 ("Main Terminal") and MT2.

SIDAC

SIDAC

Idealized breakover diode voltage and current relationships. Once the voltage exceeds the turn-on threshold, the device turns on and the voltage rapidly falls while the current increases.

The SIDAC is a less common electrically similar device, the difference in naming being determined by the manufacturer. In general, SIDACs have higher breakover voltages and current handling.

The SIDAC, or Silicon Diode for Alternating Current, is another member of the thyristor family. Also referred to as a SYDAC (Silicon thYristor for Alternating Current), bi-directional thyristor breakover diode, or more simply a bi-directional thyristor diode, it is technically specified as a bilateral voltage triggered switch. Its operation is similar to that of the DIAC, but SIDAC is always a five-layer device with low-voltage drop in latched conducting state, more like a voltage triggered TRIAC without a gate. In general, SIDACs have higher breakover voltages and current handling capacities than DIACs, so they can be directly used for switching and not just for triggering of another switching device.

The operation of the SIDAC is functionally similar to that of a spark gap. The SIDAC remains nonconducting until the applied voltage meets or exceeds its rated breakover voltage. Once entering this conductive state going through the negative dynamic resistance region, the SIDAC continues to conduct, regardless of voltage, until the applied current falls below its rated holding current. At this point, the SIDAC returns to its initial nonconductive state to begin the cycle once again.

Somewhat uncommon in most electronics, the SIDAC is relegated to the status of a special purpose device. However, where part-counts are to be kept low, simple relaxation oscillators are needed, and when the voltages are too low for practical operation of a spark gap, the SIDAC is an indispensable component.

Similar devices, though usually not functionally interchangeable with SIDACs, are the Thyristor Surge Protection Devices (TSPD), Trisil, SIDACtor, or the now-obsolete Surgector. These are designed to tolerate large surge currents for the suppression of overvoltage transients.

See also

• Shockley diode
• Triode for Alternating Current (TRIAC)
• Silicon-controlled Rectifier (SCR)
• Trisil
• Quadrac

References

• DB3 DB4 SMDB3 DIAC, ST Datasheet (PDF)
• LittelFuse Kxxx1g Series SIDAC Data Sheet (PDF)

External links

• Strobe circuit containing a SIDAC