Chipseal

Chipseal
A chip-seal paved road

Chip seal is a pavement surface treatment that combines a layer(s) of asphalt with a layer(s) of fine aggregate. In the United States, chip seals are typically used on rural roads carrying lower traffic volumes, and the process is often referred to as "asphaltic surface treatment". In Australia and New Zealand, chip sealing is referred to as a "sprayed seal" or "tarseal" and is used on a larger percentage of roads, both rural and urban.[1]

Contents

Uses

Chip seal is cheaper than resurfacing an asphalt concrete or a Portland Cement Concrete pavement, but not as long lasting. In some states of the United States, chip sealing is used in conjunction with new road construction to make the road bed more durable and longer lasting.

Installation

Chip seals are constructed by evenly distributing a thin base of hot bitumen or asphalt onto an existing pavement and then embedding finely graded aggregate into it. The aggregate is evenly distributed over the seal spray, then rolled into a smooth pavement surface. A chip seal surfaced pavement can optionally be sealed with a top layer which is referred to as a fog seal or enrichment.

The introduction of polymer-modified bitumen and emulsion binder has increased the chip seal's ability to prevent crack reflection and improve stone retention by improving the properties of the bitumen binder. Newer techniques use asphalt emulsion (a mixture of liquid asphalt, surfactant, and water) instead of asphalt. This has been shown to help reduce aggregate loss and reduce cost of installation, but can increase the occurrence of stripping. It reduces emissions of volatile organic compounds (VOCs) due to the lower solvent content.

It can keep good pavement in good condition by sealing out water, but provides no structural strength and will only repair minor cracks. While the small stones used as surface yield a relatively even surface without the edges of patches, it also results in a very rough surface that leads to significantly louder rolling noises of automobile wheels.

Although chip seal is an effective low cost way to repair road, it has some drawbacks. Loose crushed stone is often left on the surface, due to under-application of bitumen or over application of stone. If not removed, this can cause safety and environmental problems such as cracked windshields, loss-of-control crashes (especially for motorcyclists, bicyclists and small trucks), and deposition of foreign material into drainage courses. Therefore, it is very important to sweep the road after the emulsion sets.

Asphalt (or bitumen as it is known outside the United States and Canada), is the actual binder used in chip seal applications.

Noise and vibration effects

The rough wearing surface of the chipseal generates more roadway noise at any operating speed than does typical asphalt or concrete surfaces. This typically is not a major concern at very low operating speeds, moreover, chipseals are typically used on low volume rural and urban roadways. These sound intensities increase with higher vehicle speeds.[2] There is a considerable range in acoustical intensities produced depending upon the specific tire tread design and its interaction with the roadway surface type.

The rough surface causes noticeable increases in vibration and rolling resistance for bicyclists, and increased tire wear in all types of tires.

Vehicle speed can affect the set up time with chipseal. Shortly after construction (depending on weather conditions) the set speed for chip seal is 10-15 MPH for the first 24h-48h after construction.[citation needed]

See also

Bituminous Surface Treatment under Pavement (material)

References

External links


Wikimedia Foundation. 2010.

Нужно сделать НИР?

Look at other dictionaries:

  • Road — This article is about a route, thoroughfare or way that supports travel by a means of conveyance. For a place outside a harbor where a ship can lie at anchor, see Roadstead. For public roads, see Highway. For other routes, see thoroughfare. For… …   Wikipedia

  • Road surface — A road in the process of being resurfaced Road surface (British English) or pavement (American English) is the durable surface material laid down on an area intended to sustain vehicular or foot traffic, such as a road or walkway. In the past… …   Wikipedia

  • Asphalt — Note: The terms bitumen and asphalt are mostly interchangeable, except where asphalt is used as an abbreviation for asphalt concrete For other uses, see Asphalt (disambiguation). Natural bitumen from the Dead sea …   Wikipedia

  • Brick — For other uses, see Brick (disambiguation). An old brick wall in English bond laid with alternating courses of headers and stretchers …   Wikipedia

  • Concrete — This article is about the construction material. For other uses, see Concrete (disambiguation). Outer view of the Roman Pantheon, still the largest unreinforced solid concrete dome.[1] …   Wikipedia

  • Chip — Contents 1 Food 2 Media 2.1 Characters 2.2 Games …   Wikipedia

  • Highway — For other uses, see Highway (disambiguation). A German Autobahn in Lehrte …   Wikipedia

  • Roundabout — This article is about the road junction. For other uses, see Roundabout (disambiguation). Movement within a roundabout in a country where traffic drives on the right. Note the anticlockwise circulation …   Wikipedia

  • Intersection (road) — Crossroad in Kharkov An intersection is a road junction where two or more roads either meet or cross at grade (they are at the same level). An intersection may be 3 way a T junction or fork, 4 way a crossroads, or 5 way or more. It may often be… …   Wikipedia

  • Michigan left — For the Arkells album, see Michigan Left (album). Stylized depiction of the design in Grand Haven, Michigan, at US 31 and Robbins Road (north to the right), showing the additional area necessary to make a turn on a narrow median …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”