Power strip

Power strip
French/Belgian power strip

A power strip (also known as an extension block, power board and by many other variations) is a block of electrical sockets that attaches to the end of a flexible cable and allows multiple electrical devices to be plugged in. As such it can be considered a type of trailing socket though that term is more often used for single and double cable mounted sockets. The term is also used to refer to the complete assembly with the power strip on one end and a plug on the other. Power strips are often used when many electrical devices are in proximity, such as for audio/video and computer systems. Power strips often include a circuit breaker to safely limit the electric power flowing through them.



Illuminated power switch on a power strip

Power strips can include a switch to turn all devices on and off. Some have outlets which are individually switched. "Master/slave" strips can detect one "master" device being turned on or off (say the PC itself in a computer setup) and turn everything else on or off. Remote control strips allow a group of devices to be switched remotely.


Many power strips have a neon or LED indicator light or one per output socket to show when power is on. Better-quality surge-protected strips often have additional lights to indicate the status of the surge protection system.

Overload protection

Overload protection is different from surge protection. Some power strips only have overload protection, which does not protect from electricity spikes (surges); it only means that the device will trip itself when devices are plugged into it are taking more power than the strip is rated to supply. For example, the standard rating for overload protected powerboards is 2400W in Australia, and exceeding that power will make the board trip.

An overload protected board cannot cause damage to trip distribution boards that are plugged into them, that damage can only be done by surge protected board by the way the MOV's inside them are manufactured. Both boards have a reset switch. Overload protection boards generally do not have a power light.

Energy-saving features and standby power

Some power strips have energy-saving features, which switch off the strip if appliances go into standby mode. Using a sensor circuit, they detect if the level of current flowing through the socket is in standby mode (less than 30 watts), and then they will turn off that socket. This reduces the consumption of standby power used by computer peripherals and other equipment when not in use, saving money and energy. Some more-sophisticated power strips have a master and slave socket arrangement, and when the "master" socket detects standby mode in the attached appliance's current it turns off the whole strip.

However, there can be problems in detecting standby power in appliances that use more power in standby mode (e.g. plasma televisions) and are thus not turned off in the desired way. When using a master–slave power strip, one way to avoid such problems is to plug an appliance with a lower standby wattage (like a DVD player) into the master socket, using it as the master control instead.

Also it is recommended that appliances that need a controlled shutdown sequence (e.g. many ink-jet printers) not be plugged into such a strip as it can damage them. It is better use the appliance's own power switch to initiate a proper shutdown sequence.

Within Europe, power strips with energy-saving features are within the scope of the Low Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC and require CE Marking.

Socket arrangement

Italian power strip with two different types of socket

In some countries where multiple socket types are in use, a single power strip can have two or more kinds of socket.

Socket arrangement varies considerably, but for access reasons there are rarely more than two rows. In Europe, power strips without surge suppression are normally single row, but models with surge suppression are supplied both in single and double row configurations.

If sockets on a power strip are grouped closely together, a cable with a large "wall wart" transformer at its end may cover up multiple sockets. Various designs address this problem, some by simply increasing the spacing between outlets. Other designs include receptacles which rotate in their housing, or multiple short receptacle cords feeding from a central hub. A simple DIY method for adapting problematic power strips arrangements to large "wall warts" is to use a three-way socket adapter to extend the socket above its neighbors, providing the required clearance.[1]

Surge protection and filtering

German/Dutch surge protected power strip

Many power strips have built-in surge protectors and/or EMI/RFI filters: these are sometimes described as surge suppressors or electrical line conditioners. Some also provide surge suppression for phone lines, TV cable coax, or network cable. Unprotected power strips are often mistakenly called "surge suppressors" or "surge protectors" even though they may have no ability to suppress surges.

Surge suppression is usually provided by one or more metal-oxide varistors (MOVs), which are inexpensive two-terminal semiconductors. These act as very high speed switches, momentarily limiting the peak voltage across their terminals. By design, MOV surge limiters are selected to trigger at a voltage somewhat above the local mains supply voltage, so that they do not clip normal voltage peaks, but clip abnormal higher voltages. In the US, this is (nominally) 120 VAC. It should be borne in mind that this voltage specification is RMS, not peak, and also that it is only a nominal value.

In most of the developed world, mains electrical circuits are (supposed to be) grounded (earthed), so there will be a live wire, a neutral wire, and a ground wire. Power strips often come with only one MOV mounted between the live and neutral wires. More complete (and desirable) power strips will have three MOVs, mounted between each possible pair of wires. Since MOVs degrade somewhat each time they are triggered, power strips using them have a limited, and unpredictable, protective life.

More elaborate power strips may use inductor-capacitor networks to achieve a similar effect of protecting equipment from high voltage spikes on the mains circuit. These more expensive arrangements are less prone to silent degradation than MOVs.

Within the EU power strips with surge suppression circuits can demonstrate compliance with the (LVD) Low Voltage Directive 2006/95/EC (see Official Journal of the European Union at [1] by complying with the requirements of EN 61643-11:2002+A1. The standard covers both the performance of the surge suppression circuit and the safety. Likewise power strips with telecoms surge suppression circuits can demonstrate compliance with the LVD by complying with the requirements of EN 61643-21:2001.

Daisy chaining and surge protection

Connecting Power Strips in a daisy chain does not necessarily increase the protection they provide.[2] Connecting them in this manner connects their surge protection trips in parallel, spreading any potential surge across each surge protector. However, due to manufacturing tolerances of the MOVs, the surge will not be spread evenly and will typically go through the one that trips first. A single surge protector with a higher surge rating is more effective and has a longer lifetime.


Multiple power strips and AC adapters

Overloading can be a problem with any sort of power distribution adaptor. This is especially likely if multiple appliances with heating elements, such as electric room heaters or benchtop cooking appliances like electric frying pans are plugged into a power strip or similar device.

In the US and some other countries, power strips generally have a circuit breaker integrated to prevent overload. In the UK, power strips are required to be protected by the fuse in the BS 1363 plug. Some also feature a 13A BS1362 fuse in the socket end. While this is not much use if they are being fed with a 13A plug it can be very helpful for providing safe protection to adaptor leads from a higher current plug type.

Power strips are generally considered a safer alternative to "double adaptors", "two-way plugs", "three-way plugs" or "cube taps" which plug directly into the socket with no lead for multiple appliances. These low-cost adaptors are generally not fused (although more modern adaptors in the UK and Ireland are). Therefore in many cases the only protection against overload is the circuit fuse which may well have a rating higher than the adaptor. The weight of the plugs pulling on the adapter (and often pulling it part way out of the socket) can also be an issue if adaptors are stacked or if they are used with brick-style power supplies. Such adaptors, while still available, have largely fallen out of use in some countries (two and three-way adaptors are common in the UK and Ireland).

When plugging a device into a power strip, a build up of carbon can cause sparking to occur. This generally doesn't pose much of a risk, but it can bother some people.

US requirements

US power strip with switch
  • Underwriters Laboratories standard 1363 contains requirements for relocatable power taps. Included in the scope section of the standard is the statement:
    1.1 These requirements cover cord-connected, relocatable power taps rated 250 V AC or less and 20 A AC or less. A relocatable power tap is intended only for indoor use as a temporary extension of a grounding alternating-current branch circuit for general use.
  • National Electrical Code recognizes power strip as Multioutlet Assembly in Article 220.14.

UK requirements

British power strip with neon indicator

In Europe plugs and sockets without additional control or surge protection circuits are outside the scope of the Low Voltage Directive 2006/95/EC and controlled by National regulations, and therefore must not be CE marked. In the UK the legal requirements for plugs and sockets are listed in Statutory Instrument 1994 No. 1768, The Plugs and Sockets etc. (Safety) Regulations 1994.[2] This regulation lists the requirements for all domestic plugs and sockets; including socket outlet units (power strips), see [3] Electrical Equipment - Requirements for Plugs & Sockets etc. - Guidance notes on the UK Plugs & Sockets etc. (Safety) Regulations 1994 (S.I. 1994/1768).

The regulation requires all socket outlet units to comply with the requirements of BS 1363-2 Specification for 13A switched and unswitched socket-outlets and with the requirements of BS 5733 Specification for General requirements for electrical accessories. Sockets and socket outlets do not require independent approval under the regulations. Any plug fitted to the socket outlet unit must comply with the requirements of BS 1363-1 Specification for rewirable and non-rewirable 13A fused plugs. Plugs must also be independently approved and marked in accordance with the requirements of the regulation.

If a socket outlet unit contains additional control circuits or surge protection circuits they will fall within the scope of the Low Voltage Directive 2006/95/EC and must be CE marked. Socket outlet unit with control circuits also fall within the scope of the EMC Directive 2004/108/EC.


In 1972, the electrical "power-board" was invented by Australian electrical engineer Peter Talbot working under Frank Bannigan, Managing Director of Australian company Kambrook. The product was hugely successful, however, it was not patented and market share was eventually lost to other manufacturers.[3]

See also


External links

Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • power strip — noun Date: 1980 an electrical device consisting of a cord with a plug on one end and several sockets on the other …   New Collegiate Dictionary

  • power strip — noun : an electrical device consisting of a cord with a plug on one end and several sockets on the other * * * noun, pl ⋯ strips [count] US : an electrical device that has a series of outlets attached to a cord with a plug on one end …   Useful english dictionary

  • Strip — A strip is a long, thin piece of a bigger item; strip, stripping or stripped may refer to:* Landing strip or runway, where airplanes land * Landing strip, type of hairstyle * removing the insulation from the core of an electrical wire, known as… …   Wikipedia

  • Power distribution unit — TCP/IP controlled 19 PDU with USB webcam, environmental IP monitoring …   Wikipedia

  • Power supply — For the Budgie album, see Power Supply (album). A vacuum tube rackmount adjustable power supply, capable of +/ 1500 volts DC, 0 to 100mA output, with amperage limiting capability. A power supply is a device that supplies electrical energy …   Wikipedia

  • Power cord — For a musical interval played on an electric guitar, see Power chord. A power cord, line cord, or mains cable is a cable that temporarily connects an appliance to the mains electricity supply via a wall socket or extension cord. The terms are… …   Wikipedia

  • strip# — strip vb Strip, divest, denude, bare, dismantle can mean to deprive a person or thing of what clothes, furnishes, or invests him or it. Strip stresses a pulling or tearing off rather than a laying bare, though the latter implication is frequent;… …   New Dictionary of Synonyms

  • Strip-till — is a conservation system that utilizes a minimum tillage. It combines the soil drying and warming benefits of conventional tillage with the soil protecting advantages of no till by disturbing only the portion of the soil that is to contain the… …   Wikipedia

  • strip — Ⅰ. strip [1] ► VERB (stripped, stripping) 1) remove all coverings or clothes from. 2) take off one s clothes. 3) leave bare of accessories or fittings. 4) remove (paint) from a surface with solvent. 5) …   English terms dictionary

  • Strip club — Exterior photograph of a strip club advertising full nude entertainment (Cheetahs, in San Diego, California USA). A strip club is an adult entertainment venue in which striptease or other erotic or exotic dance is regularly performed. Strip clubs …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”