Model rocket

Model rocket
A typical model rocket during launch

A model rocket is a small rocket that is commonly advertised as being able to be launched by anybody, to, in general, low altitudes (usually to around 100–500 m (300–1500 ft) for a 30 g (1 oz.) model) and recovered by a variety of means.

According to the United States National Association of Rocketry (NAR) Safety Code,[1] model rockets are constructed of paper, wood, plastic and other lightweight materials. The code also provides guidelines for motor use, launch site selection, launch methods, launcher placement, recovery system design and deployment and more. Since the early 1960s, a copy of the Model Rocket Safety Code has been provided with most model rocket kits and motors. Despite its inherent association with extremely flammable substances and objects with a pointed tip traveling at high speeds, model rocketry historically has proven[citation needed] to be a very safe hobby and has been credited[citation needed] as the most significant source of inspiration for children who eventually become scientists and engineers.

The launch of a scale model of Saturn V


History of model rocketry

While there were many small rockets produced after years of research and experimentation, the first modern model rocket, and, more important, the model rocket motor, was designed in 1954 by Orville Carlisle, a licensed pyrotechnics expert, and his brother Robert, a model airplane enthusiast. They originally designed the motor and rocket for Robert to use in lectures on the principles of rocket-powered flight. But then Orville read articles written in Popular Mechanics by G. Harry Stine about the safety problems associated with young people trying to make their own rocket engines. With the launch of Sputnik, many young people were trying to build their own rocket motors, often with tragic results. Some of these attempts were dramatized in the fact-based movie October Sky. The Carlisles realized their motor design could be marketed and provide a safe outlet for a new hobby. They sent samples to Mr. Stine in January 1957. Stine, a range safety officer at White Sands Missile Range, built and flew the models, and then devised a safety handbook for the activity based on his experience at the range.


The first American model rocket company was Model Missiles Incorporated (MMI), in Denver, Colorado, opened by Stine and others. Stine had model rocket engines made by a local fireworks company recommended by Carlisle, but reliability and delivery problems forced Stine to approach others. Stine eventually approached Vernon Estes, the son of a local fireworks maker, but Model Missiles closed due to unwise business discussions. Estes founded Estes Industries in 1958 in Denver, Colorado and developed a high-speed automated machine for manufacturing solid model rocket motors for MMIk. The machine, nicknamed "Mabel", made low-cost motors with great reliability, and did so in quantities much greater than Stine needed. Stine's business faltered and this enabled Estes to market the motors separately. Subsequently, he began marketing model rocket kits in 1960, and eventually, Estes dominated the market. Estes moved his company to Penrose, Colorado in 1961. Estes Industries was acquired by Damon Industries in 1970. It continues to operate in Penrose today.

Competitors like Centuri and Cox came and went in America during the 1960s, 1970s, and 1980s, but Estes continued to control the American market, offering discounts to schools and clubs like Boy Scouts of America to help grow the hobby. In recent years, companies like Quest Aerospace have taken a small portion of the market, but Estes continues to be the main source of rockets, motors, and launch equipment for the low- to medium-power rocketry hobby today. Estes produces and sells Black Powder Rocket Motors

Since the advent of High-Power Rocketry, which began in the mid-1980s with the availability of G- through J-class motors (each letter designation has twice the energy of the one before), a number of companies have shared the market for larger and more powerful rockets. By the early 1990s, Aerotech Consumer Aerospace, LOC/Precision, and Public Missiles Limited (PML) had taken up leadership positions, while a host of engine manufacturers provided ever larger motors, and at much higher costs. Companies like Aerotech, Vulcan, and Kosdon were widely popular at launches during this time as high-power rockets routinely broke Mach 1 and reached heights over 3,000 m (10,000 ft). In a span of about five years, the largest regularly made production motors available reached N, which had the equivalent power of over 1,000 D engines combined, and could lift rockets weighing 100 kg (221 lb.) with ease. Custom motor builders continue to operate on the periphery of the market today, often creating propellants that produce colored flame (red, blue, and green being common), black smoke and sparking combinations, as well as occasionally building enormous motors of P, Q, and even R class for special projects such as extreme-altitude attempts over 17,000 m (50,000 ft).

High-power engine reliability was a significant issue in the late 1980s and early 1990s, with catastrophic engine failures occurring relatively frequently (est. 1 in 20) in motors of L class or higher. At costs exceeding $300 per motor, the need to find a cheaper and more reliable alternative was apparent. Reloadable motor designs (metal sleeves with screwed-on end caps and filled with cast propellant slugs) were introduced by Aerotech and became very popular over the span of a few years. These metal containers needed only to be cleaned and refilled with propellant and a few throw-away components after each launch. The cost of a "reload" was typically half of a comparable single use motor. While catastrophes at take-off (CATOs) still occur occasionally with reloadable motors (mostly due to poor assembly techniques by the user), the reliability of launches has risen significantly. In addition, it is possible to change the thrust profile of reloadable motors by selecting different propellant designs. Since thrust is proportional to burning surface area, propellant slugs can be shaped to produce very high thrust for a second or two, or to have a lower thrust that continues for an extended time. Depending on the weight of the rocket and the maximum speed threshold of the airframe and fins, appropriate motor choices can be used to maximize performance and the chance of successful recovery. Aerotech, Pro-38, Rouse-Tech, Loki and others have standardized around a set of common reload sizes such that customers have great flexibility in their hardware and reload selections, while there continues to be an avid group of custom engine builders who create unique designs and occasionally offer them for sale.


Model rocketry is a safe and widespread hobby. Individuals such as G. Harry Stine and Vernon Estes helped ensure this by developing and publishing the NAR Model Rocket Safety Codes [2][3][4] and by commercially producing safe, professionally designed and manufactured model rocket motors.

One of the main motivations for the development of the hobby in the 1950s and 1960s was to provide young people the opportunity to construct flying rocket models without having to engage in dangerous construction of motor units and direct handling of explosive propellants.

Model rocket motors

Anatomy of a basic model rocket engine. A typical engine is about 8cm long. 1. Nozzle; 2. Case; 3. Propellant; 4. Delay charge; 5. Ejection charge; 6. End cap

Most small model rocket motors are single-use engines, with cardboard bodies and lightweight molded ceramic nozzles, ranging in impulse class from fractional A to G. Model rockets generally use commercially manufactured black powder motors. These motors are tested and certified by the National Association of Rocketry, the Tripoli Rocketry Association(TRA) or the Canadian Association of Rocketry(CAR). Blackpowder motors come in impulse ranges from 1/8A to E, although a few F blackpowders motors have been made.

The physically largest blackpowder model rocket motors are typically E-class, for black powder is very brittle. If a large black powder motor is dropped, or is exposed to many heating/cooling cycles (for example, in a closed vehicle exposed to high heat), the propellant charge may develop hairline fractures. These fractures increase the surface area of the propellant, so that when the motor is ignited, the propellant burns much more quickly than it should, producing greater than normal internal chamber pressure inside the engine. This pressure may exceed the strength of the paper case, causing the motor to burst. A bursting motor can cause damage to the model rocket ranging from a simple ruptured motor tube or body tube to the violent ejection (and occasionally ignition) of the recovery system.

Rocket motors with power ratings higher than D to E, therefore, customarily use composite propellants made of ammonium perchlorate, potassium nitrate, aluminium powder, and a rubbery binder substance contained in a hard plastic case. This type of propellant is similar to that used in the solid rocket boosters of the space shuttle and is not as fragile as black powder, increasing motor reliability and resistance to fractures in the propellant. These motors range in impulse from size D to O. Composite motors produce more impulse per unit weight (specific impulse) than do black powder motors.

G64-10W Reload
The components of a commercially produced G64-10W motor made by Aerotech Consumer Aerospace for a 29/40-120 casing. 1. Motor Casing 2. Aft Closure 3. Forward Closure 4. Propellant Liner 5. Propellant Grains (C-Slot Geometry) 6. Delay Insulator 7. Delay Grain and Delay Spacer 8. Black Powder Ejection Charge 9. Delay O-Ring 10 & 11. Forward and Aft O-Rings 12. Forward Insulator 13. Nozzle 14. Electric Igniter

Reloadable composite-propellant motors are also available. These are commercially produced motors requiring the user to assemble propellant grains, o-rings and washers (to contain the expanding gases), delay grains and ejection charges into special non-shattering aluminum motor casings with screw-on or snap-in ends (closures). The advantage of a reloadable motor is the cost: firstly, because the main casing is reusable, reloads cost significantly less than single-use motors of the same impulse. Secondly, assembly of larger composite engines is labor-intensive and difficult to automate; off-loading this task on the consumer results in a cost savings. Reloadable motors are available from D through O class.

Motors are electrically ignited with an electric match consisting of a short length of pyrogen-coated nichrome, copper, or aluminum bridgewire pushed into the nozzle and held in place with flameproof wadding, a rubber band, a plastic plug or masking tape. On top of the propellant is a tracking delay charge, which produces smoke but in essence no thrust, as the rocket slows down and arcs over. When the delay charge has burned through, it ignites an ejection charge, which is used to deploy the recovery system.

Motor nomenclature

Rocket motors. From left, 13mm A10-0T, 18mm C6-7, 24mm D12-5, 24mm E9-4, 29mm G40-10.

Model rocket motors produced by companies like Estes Industries and Quest Aerospace are stamped with a code (such as A10-3T or B6-4) that indicates several things about the motor.

The Quest Micro Maxx engines are the smallest at a diameter of 6mm. The company Apogee Components made 10.5mm micro motors, but those were discontinued in 2001. Estes manufactures size "T" (Tiny) motors that are 13 mm in diameter by 45 mm long, while standard A, B and C motors are 18 mm in diameter by 70 mm long. Larger C, D, and E class black powder motors are also available; they are 24 mm in diameter and either 70 (C and D motors) or 95 mm long (E motors). Some motors, such as F and G single-use motors, are 29mm in diameter. High-power motors (usually reloadable) are available in 38mm, 54mm, 75mm, and 98mm diameters.

First letter

The letter at the beginning of the code indicates the motor's total impulse range (commonly measured in newton-seconds). Each letter in successive alphabetical order has up to twice the impulse of the letter preceding it. This does not mean that a given "C" motor has twice the total impulse of a given "B" motor, only that C motors are in the 5.01-10.0 N-s range while "B" motors are in the 2.51-5.0 N-s range. The designations "¼A" and "½A" are also used. For a more complete discussion of the letter codes, see Model rocket motor classification.

For instance, a B6-4 motor from Estes-Cox Corporation has a total impulse rating of 5.0 N-s. A C6-3 motor from Quest Aerospace has a total impulse of 8.5 N-s.[5]

First number

The number that comes after the letter indicates the motor's average thrust, measured in newtons. A higher thrust will result in higher liftoff acceleration, and can be used to launch a heavier model. Within the same letter class, a higher average thrust also implies a shorter burn time (e.g., a B6 motor will not burn as long as - but will have more initial thrust than - a B4). Motors within the same letter class that have different first numbers are usually for rockets with different weights. For example, a heavier rocket would require a engine with more initial thrust to get it off of the launch pad, whereas a lighter rocket would need less initial thrust and would sustain a longer burn, reaching higher altitudes.

Last number

The last number is the delay in seconds between the end of the thrust phase and ignition of the ejection charge. Black Powder Motors that end in a zero have no delay or ejection charge. Such motors are typically used as first-stage motors in multistage rockets as the lack of delay element and cap permit burning material to burst forward and ignite an upper-stage motor.

A "P" indicates that the motor is "plugged". In this case, there is no ejection charge, but a cap is in place. A plugged motor is used in rockets that do not need to deploy a standard recovery system such as small rockets that tumble or R/C glider rockets. Plugged motors are also used in larger rockets, where electronic altimeters or timers are used to trigger the deployment of the recovery system.

Composite motors usually have a letter or combination of letters after the delay length, indicating which of the manufacturer's different propellant formulations is used in that particular motor.

Reloadable motors

Reloadable motor cases. From left: 24/40, 29/40-120, 29/60, 29/100, 29/180, 29/240

Reloadable motors are specified in the same manner as model rocket single-use motors as described above. However, they have an additional designation that specifies both the diameter and maximum total impulse of the motor casing in the form of diameter/impulse. A reload designed for a 29-millimeter-diameter case with a maximum total impulse of 60 newton-seconds carries the designation 29/60 in addition to its impulse specification.

Model rocket recovery methods

Model and high-power rockets are designed to be safely recovered and flown repeatedly. The most common recovery methods are parachute and streamer. The parachute is usually blown out by the engine's ejection charge, which pops off the nose cone. The parachute is attached to the nose cone, making it pull the parachute out and make a soft landing.

Featherweight recovery

The simplest approach, which is appropriate only for the tiniest of rockets, is to let the rocket flutter back to earth after ejecting the motor. This is slightly different from tumble recovery, which relies on some system to destabilize the rocket to prevent it from entering a ballistic trajectory on its way back to earth.

Tumble recovery

Another simple approach appropriate for small rockets — or rockets with a large cross-sectional area — is to have the rocket tumble back to earth. Any rocket that will enter a stable, ballistic trajectory as it falls is not safe to use with tumble recovery. To prevent this, some such rockets use the ejection charge to slide the engine to the rear of the rocket, moving the center of mass behind the center of pressure and thus making the rocket unstable.

Nose-blow recovery

Another very simple recovery technique, used in very early models in the 1950s and occasionally in modern examples, is nose-blow recovery. This is where the ejection charge of the motor ejects the nose cone of the rocket (usually attached by a shock cord made of rubber, Kevlar string or another type of cord) from the body tube, destroying the rocket's aerodynamic profile, causing highly increased drag, and reducing the rocket's airspeed to a safe rate for landing. Nose-blow recovery is generally only suitable for very light rockets.


A typical problem with parachute recovery.

The approach used most often in small model rockets, but can be used with larger rocket models given the size of the parachute greatly increases with the size of the rocket. It uses the ejective force of the motor to deploy, or push out, the parachute or streamer. The parachute is attached to the body either directly, by means of a ripcord, or indirectly, when it is attached to the nose cone, which is in turn attached to the body by a ripcord. Typically, a ball or mass of fireproof paper or material is inserted into the body before the parachute or streamer. This allows the ejection charge to propel the fire-proof material, parachute, and nose cone without damaging the recovery equipment. Air resistance slows the rocket's fall, ending in a smooth, controlled and gentle landing.

Glide recovery

In glide recovery, the ejection charge either deploys an airfoil (wing) or separates a glider from the motor. If properly trimmed, the rocket/glider will enter a spiral glide and return safely. In some cases, radio-controlled rocket gliders are flown back to the earth by a pilot in much the way as R/C model airplanes are flown.

Some rockets (typically long thin rockets) are the proper proportions to safely glide to Earth tail-first. These are termed 'backsliders'.

Helicopter recovery

The ejection charge, through one of several methods, deploys helicopter-style blades and the rocket autorotates back to earth. The helicopter recovery usually happens when the engine's recoil creates pressure, making the nose cone pop out. There are rubber bands connected to the nosecone and three or more blades. The rubber bands pull the blades out and they provide enough drag to soften the landing. In some rockets, the fins are used as the blades as well. In these, the ejection charge pushes a tube inside that has tabs sticking out of the rocket that hold the fins during launch. Then the tab releases the rubber band-pulled fins than pivot up into helicopter position.

Other model rocketry

Aerial photography

Cameras and video cameras can be launched on model rockets to take photographs in-flight. Model rockets equipped with the Astrocam, Snapshot film camera or the Oracle or newer Astrovision digital cameras (all produced by Estes), or with homebuilt equivalents, can be used to take aerial photographs.

These aerial photographs can be taken in many ways. Mechanized timers can be used or passive methods may be employed, such as strings that are pulled by flaps that respond to wind resistance. Microprocessor controllers can also be used. However, the rocket's speed and motion can lead to blurry photographs, and quickly changing lighting conditions as the rocket points from ground to sky can have an impact on video quality. Video frames can also be stitched together to create panoramas. As parachute systems can be prone to failure or malfunction, model rocket cameras need to be protected from impact with the ground.

There are also rockets that shoot short digital videos. There are two widely used ones used on the market, both produced by Estes: the Astrovision and the Oracle. The Astrocam shoots 4 (advertised as 16, and shown when playing the video, but in real life 4)seconds of video, and can also take three consecutive digital still images in flight, with a higher resolution than the video. It takes from size B-6-3 to C-6-3 Engines. The Oracle is a more costly alternative, but is able to capture all or most of its flight and recovery. In general, it is used with "D" motors. The Oracle has been on the market longer than the Astrovision, and has a better general reputation. However, "keychain cameras" are also widely available and can be used on almost any rocket without significantly increasing drag.

There are also experimental homemade rockets that include onboard videocameras, with two methods for shooting the video. One is to radio the signal down to earth, like in the BoosterVision series of cameras. The second method for this is to record it on board and be downloaded after recovery, the method employed by the cameras above (some experimenters use the Aiptek PenCam Mega for this, the lowest power usable with this method is a C or D Motor).

Instrumentation and experimentation

Model rockets with electronic altimeters can report and or record electronic data such as maximum speed, acceleration, and altitude. Two methods of determining these things are to a) have an accelerometer and a timer and work backwards from the acceleration to the speed and then to the height and b) to have a barometer onboard with a timer and to get the height (from the difference of the pressure on the ground to the pressure in the air) and to work forwards with the time of the measurements to the speed and acceleration.

Rocket modelers often experiment with rocket sizes, shapes, payloads, multistage rockets, and recovery methods. Some rocketeers build scale models of larger rockets, space launchers, or missiles.

High-power rocketry

As with low-power model rockets, high-power rockets are also constructed from lightweight materials. Unlike model rockets, high-power rockets often require stronger materials such as fiberglass, composite materials, and aluminum to withstand the higher stresses during flights that often exceed Mach 1 (340 m/s) and over 3,000 m (10,000 ft.) altitude.

High-power rockets are propelled by larger motors ranging from class H to class O. Their motors are almost always reloadable rather than single-use in order to reduce cost. Recovery and/or multi-stage ignition may be initiated by small on-board computers, which use an altimeter or accelerometer for detecting when to ignite engines or deploy parachutes.

High-power model rockets can carry large payloads, including cameras and instrumentation such as GPS units.

The NAR and the TRA successfully sued the US Bureau of Alcohol, Tobacco, Firearms and Explosives(BATFE) over the classification of Ammonium Perchlorate Composite Propellant(APCP), the most commonly used propellant in high-power rocket motors, as an explosive. The March 13, 2009 decision by DC District court judge Reggie Walton removed APCP from the list of regulated explosives, essentially eliminating BATFE regulation of hobby rocketry.[6]

See also


  1. ^ Model Rocket Safety Code
  2. ^ Model Rocket Safety Code
  3. ^ Radio Control Rocket Glider Safety Code
  4. ^ High-Power Rocket Safety Code
  5. ^ National Association of Rocketry web site:
  6. ^ "APCP not an explosive, rules Judge Reggie B. Walton". Planet News. 16 March 2009. Retrieved 9 September 2010. 

External links

Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Model rocket motor classification — Motors for model rockets and high powered rockets are classified by total impulse into a set of letter designated ranges, from A (the smallest, though ½A, ¼A, and ⅛A motors are also available), up to O as the largest. Class A is from 1.26 newton… …   Wikipedia

  • Model Rocketry (magazine) — Model Rocketry September 1969 issue of Model Rocketry. Managing Editor Gordon Mandell Categories Hobby magazines Frequency Monthly …   Wikipedia

  • Model Missile — Inc. was the first model rocket company, founded by Orville Carlisle and G. Harry Stine in October of 1957 in Denver, Colorado[1]. External links Early Model Rocket History Timeline Categories: United States company stubsCompanies based in Denver …   Wikipedia

  • Model aircraft — A die cast Boeing 747 400 model. Model aircraft are flying or non flying models of existing or imaginary aircraft using a variety of materials including plastic, diecast metal, polystyrene, balsa wood, foam and fibreglass. Flying designs range… …   Wikipedia

  • Rocket — This article is about vehicles powered by rocket engines. For other uses, see Rocket (disambiguation). A Soyuz U, at Baikonur Site 1/5 A rocket is a missile, spacecraft, aircraft or other vehicle which obtains thrust from a rocket engi …   Wikipedia

  • Rocket engine — RS 68 being tested at NASA s Stennis Space Center. The nearly transparent exhaust is due to this engine s exhaust being mostly superheated steam (water vapor from its propellants, hydrogen and oxygen) …   Wikipedia

  • rocket — 01. Do you think that one day we will be able to send a manned [rocket] to Venus? 02. My son built a model [rocket] which can be launched up to 350 meters in the air. 03. Over a dozen people are dead, and scores wounded after a [rocket] attack on …   Grammatical examples in English

  • Model (physical) — A physical model is a smaller or larger physical copy of an object. The object being modelled may be small (for example, an atom) or large (for example, the Solar System).The geometry of the model and the object it represents are often similar in …   Wikipedia

  • Model 204 — is a Database management system for IBM and compatible mainframes, which was first deployed in 1972. It incorporates a programming language and an environment for application development. It can deal with very large databases and very high… …   Wikipedia

  • Rocket Arena — (RA) is a free modification ( mod ) for the multiplayer first person shooter games Quake, Quake II, Quake III Arena and Quake 4. There are also ports for Half Life (called Lambda Arena) and Unreal Tournament. Rocket Arena was created by David crt …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”