Punch press

Punch press

A punch press is a type of machine press used to cut holes in material. It can be small and manually operated and hold one simple die set, or be very large, CNC operated, with a multi-station turret and hold a much larger and complex die set.



Most punch presses are large machines with either a 'C' type frame, or a 'portal' (bridge) type frame. The C type has the hydraulic ram at the top foremost part, whereas the portal frame is much akin to a complete circle with the ram being centered within the frame to stop frame deflection or distortion.

All punch press machines have a table or bed with brushes or rollers to allow the sheet metal workpiece to traverse with low friction. Brushes are used where scratches on the workpiece must be minimized, as with brushed aluminium or high polished materials.

Punch presses be computer numerically controlled (CNC) able to be run in an automatic mode, according to a pre-built program, to perform the processing of the material.

The punch press is characterized by parameters such as:

  • Frame type
  • Mechanism of delivering power to the ram (mechanical, electro-mechanical or hydraulic)
  • Size of working area (e.g., 2500 x 1250 mm)
  • Single or multiple station
  • Force rating (for example, 20 tons)
  • The type of tool shop and its capacity (e.g., store revolving type, capacity 34 tool)
  • Speed or productivity (typically characterized by the speed of strokes with a step movement of 25 and 1 mm)
  • Speed of movement without shock (speed-load displacement)
  • Maximum weight of workpiece
  • Safety features
  • Power consumption
  • The type of software

Punch presses are usually referred to by their tonnage and table size. In a production environment a 30 ton press is mostly the prevalent machine used today. The tonnage needed to cut and form the material is well known so sizing tooling for a specific job is a fairly straightforward task. According to the requirement the tonnage may even go up to 2000 to 2500 ton presses.

Die set

A die set consists of a set of punches (male) and dies (female) which, when pressed together, form a hole in a workpiece (and may also deform the workpiece in some desired manner). The punches and dies are removable, with the punch being attached to the ram during the punching process. The ram moves up and down in a vertically linear motion, forcing the punch through the material into the die.


The main bed of most machines is called the 'X' Axis with the 'Y' Axis being at right angles to that and allowed to traverse under CNC control. Dependent on the size of the machine, the beds, and the sheet metal workpiece weight, the motors required to move these axis tables will vary in size and power. Older styles of machines used DC motors, however with advances in technology, today's machines mostly use AC brushless motors for drives.

CNC-controlled operation

To start a cycle, the CNC controller commands the drives to move the table along the X and the Y axis to a desired position. Once in position, the control initiates the punching sequence and pushes the ram from top dead center (TDC) to bottom dead center (BDC) through the material plane. (The terms BDC and TDC go back to older presses with pneumatic or hydraulic clutches. On today's machines BDC/TDC do not actually exist but are still used for the bottom and top of a stroke.)

On its stroke from TDC to BDC, the punch enters the material, pushing it through the die, obtaining the shape determined by the design of the punch and die set. The piece of material (slug) cut from the workpiece is ejected through the die and bolster plate and collected in a scrap container.[1] The return to TDC signals to the control to begin the next cycle.

The punch press is used for high volume production. Cycle times are often measured milliseconds. Material yield is measured as a percentage of parts to waste per sheet processed. CAD/CAM programs maximize yield by nesting parts in the layout of the sheet.

Drive Type

Flywheel drive

Most punch presses today are hydraulically powered. Older machines, however, have mechanically driven rams, meaning the power to the ram is provided by a heavy, constantly-rotating flywheel. The flywheel drives the ram using a Pitman arm. In the 19th century, the flywheels were powered by leather drive belts attached to line shafting, which in turn ran to a steam plant. In the modern workplace, the flywheel is powered by a large electric motor.

Mechanical punch press

Mechanical punch presses fall into two distinct types, depending on the type of clutch or braking system with which they are equipped. Generally older presses are "full revolution" presses that require a full revolution of the crankshaft for them to come to a stop. This is because the braking mechanism depends on a set of raised keys or "dogs" to fall into matching slots to stop the ram. A full revolution clutch can only bring the ram to a stop at the same location- top dead center. Newer presses are often "part revolution" presses equipped with braking systems identical to the brakes on commercial trucks. When air is applied, a band-type brake expands and allows the crankshaft to revolve. When the stopping mechanism is applied the air is bled, causing the clutch to open and the braking system to close, stopping the ram in any part of its rotation.

Hydraulic punch press

Hydraulic punch presses, which power the ram with a hydraulic cylinder rather than a flywheel, and are either valve controlled or valve and feedback controlled. Valve controlled machines usually allow a one stroke operation allowing the ram to stroke up and down when commanded. Controlled feedback systems allow the ram to be proportionally controlled to within fixed points as commanded. This allows greater control over the stroke of the ram, and increases punching rates as the ram no longer has to complete the traditional full stroke up and down but can operate within a very short window of stroke.

Servo drive turret punch press

Servo drive turret punch press uses twin AC servo drives directly coupled to the drive shaft. This drive system combines the simplicity of the original clutch and brake technology with the speed of the hydraulic ram driven systems. This results in high performance, reliability, and lower operating costs. Servo drive press system doesn't have complex hydraulics and oil-cooling chillers reducing maintenance and repair costs. Turret press can be equipped with an advanced technology that stores and reuses energy generated during ram deceleration, providing extended electrical power savings.



  1. ^ Todd, Allen & Alting 1994, pp. 107–108.


Wikimedia Foundation. 2010.

Поможем написать курсовую

Look at other dictionaries:

  • punch press — Punch Punch, v. t. [imp. & p. p. {Punched}; p. pr. & vb. n. {Punching}.] [From {Punch}, n., a tool; cf. F. poin[,c]onner.] To perforate or stamp with an instrument by pressure, or a blow; as, to punch a hole; to punch ticket. [1913 Webster]… …   The Collaborative International Dictionary of English

  • Punch press — Punch Punch, n. [Abbrev. fr. puncheon.] 1. A tool, usually of steel, variously shaped at one end for different uses, and either solid, for stamping or for perforating holes in metallic plates and other substances, or hollow and sharpedged, for… …   The Collaborative International Dictionary of English

  • punch press — n. a press in which dies are fitted for cutting, shaping, or stamping metal …   English World dictionary

  • Punch press — Punch press. См. Штамповочный пресс. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • punch press — punch′ press n. mac a power driven machine used to cut, draw, or shape material, as metal sheets, with dies • Etymology: 1910–15 …   From formal English to slang

  • punch press — Mach. a power driven machine used to cut, draw, or otherwise shape material, esp. metal sheets, with dies, under pressure or by heavy blows. [1910 15] * * * Machine tool that changes the size or shape of a piece of material, usually sheet metal,… …   Universalium

  • punch press — noun a power driven press used to shape metal parts • Hypernyms: ↑press, ↑mechanical press • Hyponyms: ↑bench press * * * noun also punching press : a press for working on metal or other materials by the u …   Useful english dictionary

  • punch press — noun Date: 1911 a press equipped with cutting, shaping, or combination dies for working on material (as metal) …   New Collegiate Dictionary

  • Punch press — Штамповальный пресс; Дыропробивной пресс …   Краткий толковый словарь по полиграфии

  • punch press — machine power tool used metalworking and for punching holes in metal …   English contemporary dictionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”