Cross Creek Railway Station

Cross Creek Railway Station
Cross Creek
New Zealand Government Railways
regional rail
Rimutaka Incline 01.JPG
Cross Creek station yard, looking west at the start of the incline.
Station statistics
Coordinates 41°10′3.39″S 175°12′56.64″E / 41.1676083°S 175.2157333°E / -41.1676083; 175.2157333
Lines Wairarapa Line
Platforms None
Other information
Opened 12 October 1878
Closed 30 October 1955
Owned by Railways Department
Formerly Cross's Creek

Cross Creek railway station was the base of operations for the Rimutaka Incline, a Fell railway over the Rimutaka Ranges, and part of the original Wairarapa Line between Upper Hutt and Featherston in the Wellington region of New Zealand’s North Island.

This station existed solely for the operational requirements of the Incline. It did not consign goods, or serve any local settlements, save for the railway staff that were based there.



Though the origin of the name Cross Creek has not always been clear, it is generally accepted based on the writings of surveyor John Rochfort that it was derived from a Mr. Lot Cross, who lived and farmed in the vicinity of the site that was later to become the station. In the early days of the railway, it was known as Cross’s Creek, but was simplified to Cross Creek in the 1880s.


Construction of the station was included in the Incline Contract, which was to cover formation works from south of the Summit Tunnel to Featherston. It was awarded to contractor Charles McKirdy for the sum of £49,029 on 5 October 1875.

The station started out with a simple yard layout that included; the safety siding, two loops with capacities of 20 and 26 wagons, and a two road engine shed at the south end. The insufficiency of this arrangement soon became apparent, and additional sidings were laid. Increasing use of the line prompted periodic additions of sidings to the yard as required, with the ultimate capacity being reached in 1915.

A coal storage shed was attached to the locomotive shed, which was extended in 1882 using materials from the dismantled Kaitoke goods shed. In 1889, the locomotive shed was extended, but by 1899 operational requirements meant that further storage space was required. With insufficient room to extend the locomotive shed on its existing site, a new four-road depot was constructed – with a fitter’s workshop attached to the western side – at the north end of the yard. The Locomotive Foreman’s office was built in 1914 on a bank above the engine shed. A coaling stage was provided alongside one of the roads to the engine shed, from which coal was shovelled into the Fell locomotives. A shelter and pit were installed on a nearby siding which was used for changing the brake blocks on the Fell brake vans.

The only amenities provided for passenger traffic through the station was a small shelter shed and an office for the traffic staff. There were quite a few houses, these generally being reserved for management or staff with families, especially after the construction in the early 1900s of a dormitory for single members of staff. The station also boasted a school and swimming pool to cater for the children living there.


Cross Creek always had locomotives based there including, until 1880, the four Fell locomotives plus two others. After the closure of the locomotive shed at Featherston in 1891, all locomotives working the South Wairarapa district – except for the Greytown Branch – were based at Cross Creek. A new engine shed was constructed at Cross Creek in 1899. Because of the maintenance requirements of the Fell locomotives, and the distance of the station from the Petone Workshops, it was necessary to maintain a workshop on site and to have a fitter permanently based there. In 1902, the promotion of a fitter to the position of Assistant Locomotive Foreman for Cross Creek, subordinate to the Locomotive Foreman of Wellington, effectively meant that there were two fitters based at Cross Creek. A third fitter was appointed in 1911, and remained until a reduction in traffic over the line, probably after World War I. The workshops were attached to the side of the locomotive stables, and were capable of handling all but the heaviest of repair and maintenance jobs. Records show that it was normal practice for one of the six Fell locomotives to be away at Petone Workshops for medium to heavy repairs or maintenance at any given time.

Cross Creek was one of the first stations on the Wairarapa Line to receive signals, with the Working Timetable of 1887 being the first to list them. Instructions for the crossing of trains laid down that southbound trains were to take the siding or loop, and northbound trains were to take the main line. There were two safety sidings, each of which had a ground disc to indicate its position. A home signal was also installed at the foot of the incline, and a starting signal controlled trains leaving for Featherston at the other end of the yard. Though there was a building next to the station in which a lever frame was used to set some points using mechanical interlocking, this was never as extensive as at other stations.

An instruction issued in 1885 regarding the use of the safety siding at Cross Creek stated that the points from the Incline must always be set to the safety siding. When a descending train approached Cross Creek, the driver of the leading locomotive gave one long whistle to signal that the train was under control, whereupon the signalman set the points for the arrival road. If there was a problem, the driver had to sound three short whistle blasts in rapid succession, at frequent intervals. No such emergency is known to have occurred.


In considering alternatives for a railway between the Hutt Valley and the Wairarapa district to bypass the increasingly costly Rimutaka Incline, various proposals for a tunnel were considered that would have involved an eastern portal emerging at Cross Creek. Despite all the work done on investigating these ideas, the alignment eventually chosen was one that saw the tunnel emerging into the Wairarapa in a gully to the north. Once work commenced on the Rimutaka Tunnel, the fate of Cross Creek was sealed.

The last train through the station was the Wellington-bound Carterton Show Day excursion on Saturday, 29 October 1955. It carried most of the inhabitants of Cross Creek to a farewell party at Summit, after which they were returned home in a couple of carriages that had been delivered earlier in the day. The station was closed by the following day along with the rest of the line over the Rimutaka Ranges. By March 1956 most of the track between Summit and Pigeon Bush had been lifted and the buildings were sold on site for removal.


Cross Creek became part of the Rimutaka Rail Trail, which was established and is maintained by the Conservation Department, and was opened on 1 November 1987. Some remnants of the sites former usage remain, most notably the concrete foundations of the locomotive shed, the pit in which the brake blocks for the Fell brake vans were replaced, and the turntable pit. For the benefit of hikers the Conservation Department erected a shelter shed when preparing the site for the rail trail, and have since installed several plaques that point out and describe various features of the yard.


The Rimutaka Incline Railway Heritage Trust plans to reinstate and operate a heritage railway between Maymorn and Featherston on the original Wairarapa Line railway formation over the Rimutaka Ranges. Stage 3 of the project involves construction and operation of the Incline section between Summit and Cross Creek using Fell locomotives and brake vans.

See also


  • Cameron, Walter Norman (1976). A Line Of Railway: The Railway Conquest of the Rimutakas. Wellington: New Zealand Railway and Locomotive Society. ISBN 0-908573-00-6. 

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Diamond Creek railway station — Diamond Creek Station information Code DCK Distance from Flinders Street 31.4 km (19.5 mi) Operator Metro Tr …   Wikipedia

  • Menzies Creek railway station — Menzies Creek Station Information Line Gembrook line (Puffing Billy) Distance from Flinders Street 47.5km Number of Platforms 2 Number of Tracks 3 …   Wikipedia

  • Wolli Creek railway station, Sydney — Cityrail Station alt|code=WOC| Wolli Creek servicearea=South Coast Line|servicearea color=#South Coast line colour|servicearea textcolor=white servicearea2=Illawarra Eastern Suburbs Line|servicearea color2=#Illawarra line colour|servicearea… …   Wikipedia

  • Diamond Creek railway station, Melbourne — MelbourneRailwayStation1 NAME=Diamond Creek IMAGELINK=Diamond creek station platform.jpg CAPTION=Looking north away from the city from the Hurstbridge Road level crossing, platform 1 on the left CODE=DCK DISTANCE=31.4 km LINES=Hurstbridge… …   Wikipedia

  • Riddells Creek railway station, Victoria — VlineRailwayStation1 NAME=Riddells Creek CODE=RCK DISTANCE=km to mi|58.90|abbr=yes LINES=Echuca Swan Hill PLATFORMS=2 TRACKS=2 STATUS=Staffed part time FACILITIES= [ Link] TIMETABLES=… …   Wikipedia

  • Cross Creek — As a place in the United States, Cross Creek may refer to: Cross Creek (Florida), a waterway connecting Orange Lake and Lochloosa Lake in southeastern Alachua County Cross Creek, Florida, a community centered on the Cross Creek waterway Cross… …   Wikipedia

  • Railway station layout — A railway station is a place where trains make scheduled stops. Stations usually have one or more platforms constructed alongside a line of railway. However, railway stations come in many different configurations influenced by such factors as the …   Wikipedia

  • Pigeon Bush Railway Station — Infobox Station name=Pigeon Bush type=New Zealand Government Railways Department regional rail image size= image caption=Southern end of the Pigeon Bush station yard, looking north east in the direction of Featherston. address=Featherston Cross… …   Wikipedia

  • Martin Place railway station — Martin Place …   Wikipedia

  • Melbourne Central railway station — Melbourne Central Station information Code MCE …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”