Process corners

In semiconductor manufacturing, a process corner is an example of a design-of-experiments (DoE) technique that refers to a variation of fabrication parameters used in applying an integrated circuit design to a semiconductor wafer. Process corners represent the extremes of these parameter variations within which a circuit that has been etched onto the wafer must function correctly. A circuit running on devices fabricated at these process corners may run slower or faster than specified and at lower or higher temperatures and voltages, but if the circuit does not function at all at any of these process extremes the design is considered to have inadequate design margin.^[1]

In order to verify the robustness of an integrated circuit design, semiconductor manufacturers will fabricate corner lots, which are groups of wafers that have had process parameters adjusted according to these extremes, and will then test the devices made from these special wafers at varying increments of environmental conditions, such as voltage, clock frequency, and temperature, applied in combination (two or sometimes all three together) in a process called characterization.^[2] The results of these tests are plotted using a graphing technique known as a shmoo plot^[3] that indicates clearly the boundary limit beyond which a device begins to fail for a given combination of these environmental conditions.

Corner-lot analysis is most effective in digital electronics because of the direct effect of process variations on the speed of transistor switching during transitions from one logic state to another, which is not relevant for analog circuits, such as amplifiers. Analog techniques rely more on over-design and simulation software tools such as SPICE, or Monte Carlo analysis.^[4]

Significance to digital electronics

In Very-Large-Scale Integration (VLSI) integrated circuit microprocessor design and semiconductor fabrication, a process corner represents a three or six sigma variation from nominal doping concentrations (and other parameters^[5]) in transistors on a silicon wafer. This variation can cause significant changes in the duty cycle and slew rate of digital signals, and can sometimes result in catastrophic failure of the entire system.

Variation may occur for many reasons, such as minor changes in the humidity or temperature changes in the clean-room when wafers are transported, or due to the position of the die relative to the center of the wafer.

Types of corners

One naming convention for process corners is to use two-letter designators, where the first letter refers to the N-channel MOSFET (NMOS) corner, and the second letter refers to the P channel (PMOS) corner. In this naming convention, three corners exist: typical, fast and slow. Fast and slow corners exhibit carrier mobilities that are higher and lower than normal, respectively. For example, a corner designated as FS denotes fast NFETs and slow PFETs.

There are therefore five possible corners: typical-typical (TT) (not really a corner of an n vs. p mobility graph, but called a corner, anyway), fast-fast (FF), slow-slow (SS), fast-slow (FS), and slow-fast (SF). The first three corners (TT, FF, SS) are called even corners, because both types of devices are affected evenly, and generally do not adversely affect the logical correctness of the circuit. The resulting devices can function at slower or faster clock frequencies, and are often binned as such. The last two corners (FS, SF) are called "skewed" corners, and are cause for concern. This is because one type of FET will switch much faster than the other, and this form of imbalanced switching can cause one edge of the output to have much less slew than the other edge. Latching devices may then record incorrect values in the logic chain.

In addition to the FETs themselves, there are more on-chip variation (OCV) effects that manifest themselves at smaller technology nodes. These include process, voltage and temperature (PVT) variation effects on on-chip interconnect, as well as via structures.

Accounting for corners

To combat these variation effects, modern technology processes often supply SPICE or BSIM simulation models for all (or, at the least, TT, FS, and SF) process corners, which enables circuit designers to detect corner skew effects before the design is laid out, as well as post-layout (through parasitics extraction), before it is taped out.

References

1. ^ Weste, Neil H.E. and Harris, David (2005). CMOS VLSI Design: A Circuits and Systems Perspective, 3rd Ed.,. Addison-Wesley, pp.231-235. ISBN 0-321-14901-7. 
2. ^ "ASIC Product Engineering Handbook". Texas Instruments. 2001. http://www.angelfire.com/retro/norbert972/notes/pehandbook.pdf. Retrieved 2010-06-20, p.2. 
3. ^ "ASIC Product Engineering Handbook". Texas Instruments. 2001. http://www.angelfire.com/retro/norbert972/notes/pehandbook.pdf. Retrieved 2010-06-20, p.200. 
4. ^ Nenni, Daniel (2009-11-23). "Moore’s Law and 40nm Yield". http://danielnenni.com/2009/11/23/moores-law-and-40nm-yield/. Retrieved 2010-06-20. 
5. ^ Goering, Richard (2005-11-21). "Variability upends designers' plans". EETimes.com. http://www.eetimes.com/news/latest/showArticle.jhtml?articleID=174301075. Retrieved 2009-01-22. 

External links

• 3sigma.com - Why Three Sigma?
• US Patent# 6606729 - Corner simulation methodology