M-derived filter

M-derived filter

m-type filters or m-derived filters are a type of electronic filter designed using the image method. They were invented by Otto Zobel in the early 1920s. This filter type was originally intended for use with telephone multiplexing and was an improvement on the existing constant k type filter. The main problem being addressed was the need to achieve a better match of the filter into the terminating impedances. All filters designed by the image method, in general, fail to give an exact match but the m-type filter is a big improvement with suitable choice of the parameter m. The m-type filter section has a further advantage in that there is a rapid transition from the cut-off frequency of the pass band to a pole of attenuation just inside the stop band. However, there is a drawback with m-type filters. At frequencies past the pole of attenuation, the response starts to rise again and m-types have poor stop band rejection. For this reason filters designed using m-type sections are often designed as composite filters using a mixture of k-type and m-type sections and different values of m at different points to get the optimum performance from both types.

__TOC__

Background

Zobel patented an impedance matching network in 1920 [Zobel, O J, "Terminating network for filters", US patent 1 557 229, filed 30 April 1920, issued 13 Oct 1925] which, in essence, used the topology of what are now called m-type filters but Zobel did not name them as such or analyse them by the image method. This pre-dated George Campbell's publication of his constant k-type design in 1922 [Campbell, G A, "Physical Theory of the Electric Wave-Filter", "Bell System Tech J", November 1922, vol 1, no 2, pp 1-32.] . Zobel published the image analysis theory of m-type filters in 1923. [Zobel, O. J.,"Theory and Design of Uniform and Composite Electric Wave Filters", Bell Systems Technical Journal, Vol. 2 (1923), pp. 1-46.]

Derivation

The building block of m-derived filters, as with all image impedance filters, is the "L" network, called a half-section, composed of a series impedance "Z", and a shunt admittance "Y". The m-derived filter is a derivative of the constant k filter, the starting point of the design being the values of "Z" and "Y" derived from the constant k protoype and given by

: k^2=frac{Z}{Y}

where "k" is the nominal impedance of the filter, or "R"0. The designer now multiplies "Z" and "Y" by an arbitrary constant "m" (0 < "m" < 1). There are two different kinds of m-derived section; series and shunt. To obtain the m-derived series half section, the designer determines the impedance that must be added to 1/mY to make the image impedance "Z"iT the same as the image impedance of the original constant k section. From the general formula for image impedance, the additional impedance required can be shown to be

: frac{1-m^2}{m}Z.

To obtain the m-derived shunt half section, an admittance is added to 1/mZ to make the image impedance Z the same as the image impedance of the original half section. The additional admittance required can be shown to be

: frac{1-m^2}{m}Y.

The general arrangements of these circuits are shown in the diagrams to the right along with a specific example of a low pass section.

A consequence of this design is that the m-derived half section will match a k-type section on one side only. Also, an m-type section of one value of m will not match another m-type section of another value of m except on the sides which offer the Zi of the k-type.

Operating frequency

For the low-pass half section shown, the cut-off frequency of the m-type is the same as the k-type and is given by

: omega_c=frac{1}{sqrt{LC.

The pole of attenuation occurs at;

: omega_infin=frac{omega_c}{sqrt{1-m^2.

From this it is clear that smaller values of m will produce omega_infin closer to the cut-off frequency omega_c,! and hence will have a sharper cut-off. Unfortunately, it also brings the unwanted stop band response of the m-type closer to the cut-off frequency, making it more difficult for this to be filtered with subsequent sections. The value of m chosen is usually a compromise between these conflicting requirements. There is also a practical limit to how small m can be made due to the inherant resistance of the inductors. This has the effect of causing the pole of attenuation to be less deep (that is, it is no longer a genuinely infinite pole) and the slope of cut-off to be less steep. This effect becomes more marked as omega_infin is brought closer to omega_c,! and there ceases to be any improvement in response with an m of about 0.2 or less. [Bode, Hendrik W., "Wave Filter", US patent 2 002 216, , filed 7 June 1933, issued 21 May 1935.]

Image impedance

:"See also Image impedance#Derivation"The following expressions for image impedances are all referenced to the low-pass prototype section. They are scaled to the nominal impedance "R"0 = 1 and the frequencies in those expressions are all scaled to the cut-off frequency ωc = 1.

eries sections

The image impedances of the series section are given by

: Z_{iT}=sqrt{1-omega^2}

and is the same as the constant k section.

: Z_{iPi m}=frac{1-left(omega/omega_infin ight)^2}{sqrt{1-omega^2.

hunt sections

The image impedances of the shunt section are given by

: Z_{iPi}=frac{1}{sqrt{1-omega^2

and is the same as the constant k section.

: Z_{iT m}=frac{sqrt{1-omega^2{1-left(omega/omega_infin ight)^2}

As with the k-type section, the image impedance of the m-type low-pass section is purely real below the cut-off frequency and purely imaginary above it. From the chart it can be seen that in the passband the closest impedance match to a constant pure resistance termination occurs at approximately "m" = 0.6.

Transmission parameters

:"See also Image impedance#Transfer function"For an m-derived section in general the transmission parameters for a half-section are given by;

gamma=sinh^{-1}frac{mZ}{sqrt{k^2+(1-m^2)Z

And for n half-sections;

gamma_n=ngamma,!

For the particular example of the low-pass L section, the transmission parameters solve differently in three frequency bands.

For 0 the transmission is lossless;

: gamma = alpha + ieta = 0 + ifrac{1}{2} cos^{-1} left(1-frac{2m^2} {left(frac{omega_c}{omega} ight)^2 - left(frac{omega_c}{omega_{infin ight)^2} ight)

For omega_c the transmission parameters are;

: gamma = alpha + ieta = frac{1}{2} cosh^{-1} left(frac{2m^2}{left(frac{omega_c}{omega} ight)^2 - left( frac{omega_c}{omega_{infin ight)^2} - 1 ight) + ifrac{pi}{2}

For omega_infin the transmission parameters are;

: gamma = alpha + ieta = frac{1}{2} cosh^{-1} left(1-frac{2m^2}{left(frac{omega_c}{omega} ight)^2 - left( frac{omega_c}{omega_{infin ight)^2} ight) +i0

Prototype transformations

The plots shown of image impedance, attenuation and phase change are the plots of a low-pass prototype filter section. The prototype has a cut-off frequency of ωc=1 rad/s and a nominal impedance R0=1Ω. This is produced by a filter half-section where L=1 henry and C=1 farad. This prototype can be impedance scaled and frequency scaled to the desired values. The low-pass prototype can also be transformed into high-pass, band-pass or band-stop types by application of suitable frequency transformations.

Cascading sections

Several L half-sections may be cascaded to form a composite filter. Like impedance must always face like in these combinations. There are therefore two circuits that can be formed with two identical L half-sections. Where ZiT faces ZiT, the section is called a Π section. Where Z faces Z the section so formed is a T section. Further additions of half-sections to either of these forms a ladder network which may start and end with series or shunt elements.

It should be born in mind that the characteristics of the filter predicted by the image method are only accurate if the section is terminated with its image impedance. This is usually not true of the sections at either end which are usually terminated with a fixed resistance. The further the section is from the end of the filter, the more accurate the prediction will become since the effects of the terminating impedances are masked by the intervening sections. It is usual to provide half half-sections at the ends of the filter with m=0.6 as this value gives the flattest Z_i in the passband and hence the best match in to a resistive termination.

ee also

*Image impedance
*Constant k filter
*mm'-type filter
*Composite image filter

References

:* Mathaei, Young, Jones "Microwave Filters, Impedance-Matching Networks, and Coupling Structures" McGraw-Hill 1964.:*For a simpler treatment of the analysis see,::*Ghosh, Smarajit, "Network Theory: Analysis and Synthesis", Prentice Hall of India, pp564-569.


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Filter binding assay — In biochemistry, one of the ways to learn about an interaction between two molecules is to determine the binding constant, which is a number that describes the ratio of unbound and bound molecules. This information reveals the affinity between… …   Wikipedia

  • filter tip — UK / US noun [countable] Word forms filter tip : singular filter tip plural filter tips a) an object at the end of a cigarette that removes some of the harmful chemicals from the smoke b) a cigarette with a filter tip Derived word: filter tipped… …   English dictionary

  • mm'-type filter — Linear analog electronic filters Network synthesis filters Butterworth filter Chebyshev filter Elliptic (Cauer) filter Bessel filter Gaussian filter Optimum L (Legendre) filter Linkwitz Riley filter …   Wikipedia

  • Composite image filter — Linear analog electronic filters Network synthesis filters Butterworth filter Chebyshev filter Elliptic (Cauer) filter Bessel filter Gaussian filter Optimum L (Legendre) filter Linkwitz Riley filter …   Wikipedia

  • Electronic filter topology — An elementary filter topology introduces a capacitor into the feedback path of an op amp to achieve an unbalanced active implementation of a low pass transfer function Electronic filter topology defines electronic filter circuits without taking… …   Wikipedia

  • Constant k filter — Linear analog electronic filters Network synthesis filters Butterworth filter Chebyshev filter Elliptic (Cauer) filter Bessel filter Gaussian filter Optimum L (Legendre) filter Linkwitz Riley filter …   Wikipedia

  • Chebyshev filter — Linear analog electronic filters Network synthesis filters Butterworth filter Chebyshev filter Elliptic (Cauer) filter Bessel filter Gaussian filter Optimum L (Legendre) filter Linkwitz Riley filter …   Wikipedia

  • Optimum "L" filter — Linear analog electronic filters Network synthesis filters Butterworth filter Chebyshev filter Elliptic (Cauer) filter Bessel filter Gaussian filter Optimum L (Legendre) filter Linkwitz Riley filter …   Wikipedia

  • Kalman filter — Roles of the variables in the Kalman filter. (Larger image here) In statistics, the Kalman filter is a mathematical method named after Rudolf E. Kálmán. Its purpose is to use measurements observed over time, containing noise (random variations)… …   Wikipedia

  • Elliptic filter — An elliptic filter (also known as a Cauer filter, named after Wilhelm Cauer) is an electronic filter with equalized ripple (equiripple) behavior in both the passband and the stopband. The amount of ripple in each band is independently adjustable …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”