Binary multiplier

Binary multiplier

A binary multiplier is an electronic circuit used in digital electronics, such as a computer, to multiply two binary numbers. It is built using binary adders.

A variety of computer arithmetic techniques can be used to implement a digital multiplier. Most techniques involve computing a set of partial products, and then summing the partial products together. This process is similar to the method taught to primary schoolchildren for conducting long multiplication on base-10 integers, but has been modified here for application to a base-2 (binary) numeral system.

Contents

History

Until the late 1970s, most minicomputers did not have a multiply instruction, and so programmers used a "multiply routine"[1][2] which repeatedly shifts and accumulates partial results, often written using loop unwinding. Mainframe computers had multiply instructions, but they did the same sorts of shifts and adds as a "multiply routine".

Early microprocessors also had no multiply instruction. The Motorola 6809, introduced in 1978, was one of the earliest microprocessors with a dedicated hardware multiply instruction. It did the same sorts of shifts and adds as a "multiply routine", but implemented in the microcode of the MUL instruction.[citation needed]

As more transistors per chip became available due to larger-scale integration, it became possible to put enough adders on a single chip to sum all the partial products at once, rather than reuse a single adder to handle each partial product one at a time.

Because some common digital signal processing algorithms spend most of their time multiplying, digital signal processor designers sacrifice a lot of chip area in order to make the multiply as fast as possible; a single-cycle multiply–accumulate unit often used up most of the chip area of early DSPs.

Multiplication basics

The method taught in school for multiplying decimal numbers is based on calculating partial products, shifting them to the left and then adding them together. The most difficult part is to obtain the partial products, as that involves multiplying a long number by one digit (from 0 to 9):

     123
   x 456
   =====
     738  (this is 123 x 6)
    615   (this is 123 x 5, shifted one position to the left)
 + 492    (this is 123 x 4, shifted two positions to the left)
   =====
   56088

A binary computer does exactly the same, but with binary numbers. In binary encoding each long number is multiplied by one digit (either 0 or 1), and that is much easier than in decimal, as the product by 0 or 1 is just 0 or the same number. Therefore, the multiplication of two binary numbers comes down to calculating partial products (which are 0 or the first number), shifting them left, and then adding them together (a binary addition, of course):

       1011   (this is 11 in binary)
     x 1110   (this is 14 in binary)
     ======
       0000   (this is 1011 x 0)
      1011    (this is 1011 x 1, shifted one position to the left)
     1011     (this is 1011 x 1, shifted two positions to the left)
  + 1011      (this is 1011 x 1, shifted three positions to the left)
  =========
   10011010   (this is 154 in binary)

This is much simpler than in the decimal system, as there is no table of multiplication to remember: just shifts and adds.

This method is mathematically correct, but it has two serious engineering problems. The first is that it involves 32 intermediate additions in a 32-bit computer, or 64 intermediate additions in a 64-bit computer. These additions take a lot of time. The engineering implementation of binary multiplication consists, really, of taking a very simple mathematical process and complicating it a lot, in order to do fewer additions; a modern processor can multiply two 64-bit numbers with 16 additions (rather than 64), and can do several steps in parallel—but at a cost of making the process almost unreadable.

The second problem is that the basic school method handles the sign with a separate rule ("+ with + yields +", "+ with - yields -", etc.). Modern computers embed the sign of the number in the number itself, usually in the two's complement representation. That forces the multiplication process to be adapted to handle two's complement numbers, and that complicates the process a bit more. Similarly, processors that use ones' complement, sign-and-magnitude, IEEE-754 or other binary representations require specific adjustments to the multiplication process.

Engineering approach: an unsigned example

For example, suppose we want to multiply two unsigned eight bit integers together: a[7:0] and b[7:0]. We can produce eight partial products by performing eight one-bit multiplications, one for each bit in multiplicand a:

 p0[7:0] = a[0] × b[7:0] = {8{a[0]}} & b[7:0]
 p1[7:0] = a[1] × b[7:0] = {8{a[1]}} & b[7:0]
 p2[7:0] = a[2] × b[7:0] = {8{a[2]}} & b[7:0]
 p3[7:0] = a[3] × b[7:0] = {8{a[3]}} & b[7:0]
 p4[7:0] = a[4] × b[7:0] = {8{a[4]}} & b[7:0]
 p5[7:0] = a[5] × b[7:0] = {8{a[5]}} & b[7:0]
 p6[7:0] = a[6] × b[7:0] = {8{a[6]}} & b[7:0]
 p7[7:0] = a[7] × b[7:0] = {8{a[7]}} & b[7:0]

where {8{a[0]}} means repeating a[0] (the 0th bit of a) 8 times (Verilog notation).

To produce our product, we then need to add up all eight of our partial products, as shown here:

                                                p0[7] p0[6] p0[5] p0[4] p0[3] p0[2] p0[1] p0[0]
                                        + p1[7] p1[6] p1[5] p1[4] p1[3] p1[2] p1[1] p1[0] 0
                                  + p2[7] p2[6] p2[5] p2[4] p2[3] p2[2] p2[1] p2[0] 0     0
                            + p3[7] p3[6] p3[5] p3[4] p3[3] p3[2] p3[1] p3[0] 0     0     0
                      + p4[7] p4[6] p4[5] p4[4] p4[3] p4[2] p4[1] p4[0] 0     0     0     0
                + p5[7] p5[6] p5[5] p5[4] p5[3] p5[2] p5[1] p5[0] 0     0     0     0     0
          + p6[7] p6[6] p6[5] p6[4] p6[3] p6[2] p6[1] p6[0] 0     0     0     0     0     0
    + p7[7] p7[6] p7[5] p7[4] p7[3] p7[2] p7[1] p7[0] 0     0     0     0     0     0     0
-------------------------------------------------------------------------------------------
P[15] P[14] P[13] P[12] P[11] P[10]  P[9]  P[8]  P[7]  P[6]  P[5]  P[4]  P[3]  P[2]  P[1]  P[0]

In other words, P[15:0] is produced by summing p0, p1 << 1, p2 << 2, and so forth, to produce our final unsigned 16-bit product.

Engineering approach: signed integers

If b had been a signed integer instead of an unsigned integer, then the partial products would need to have been sign-extended up to the width of the product before summing. If a had been a signed integer, then partial product p7 would need to be subtracted from the final sum, rather than added to it.

The above array multiplier can be modified to support two's complement notation signed numbers by inverting several of the product terms and inserting a one to the left of the first partial product term:

                                                    1  -p0[7]  p0[6]  p0[5]  p0[4]  p0[3]  p0[2]  p0[1]  p0[0]
                                                -p1[7] +p1[6] +p1[5] +p1[4] +p1[3] +p1[2] +p1[1] +p1[0]   0
                                         -p2[7] +p2[6] +p2[5] +p2[4] +p2[3] +p2[2] +p2[1] +p2[0]   0      0
                                  -p3[7] +p3[6] +p3[5] +p3[4] +p3[3] +p3[2] +p3[1] +p3[0]   0      0      0
                           -p4[7] +p4[6] +p4[5] +p4[4] +p4[3] +p4[2] +p4[1] +p4[0]   0      0      0      0
                    -p5[7] +p5[6] +p5[5] +p5[4] +p5[3] +p5[2] +p5[1] +p5[0]   0      0      0      0      0
             -p6[7] +p6[6] +p6[5] +p6[4] +p6[3] +p6[2] +p6[1] +p6[0]   0      0      0      0      0      0
   1  +p7[7] -p7[6] -p7[5] -p7[4] -p7[3] -p7[2] -p7[1] -p7[0]   0      0      0      0      0      0      0
 ------------------------------------------------------------------------------------------------------------
P[15]  P[14]  P[13]  P[12]  P[11]  P[10]   P[9]   P[8]   P[7]   P[6]   P[5]   P[4]   P[3]   P[2]   P[1]  P[0]

Do not be misled by the minus sign (-) notation above. It does not mean arithmetic negation ( -(7) = -7), but instead binary complementation, more commonly denoted x\prime (read x prime), \bar x (x bar) or ~x (tilde x), achieved by flipping all the bits. In two's complement to get the negation of a number, you complement the number then add 1, so they are NOT equivalent.

There are a lot of simplifications in the bit array above that are not shown and are not obvious. The sequences of one complemented bit followed by noncomplemented bits are implementing a two's complement trick to avoid sign extension. The sequence of p7 (noncomplemented bit followed by all complemented bits) is because we're subtracting this term so they were all negated to start out with (and a 1 was added in the least significant position). For both types of sequences, the last bit is flipped and an implicit -1 should be added directly below the MSB. When the +1 from the two's complement negation for p7 in bit position 0 (LSB) and all the -1's in bit columns 7 through 14 (where each of the MSBs are located) are added together, they can be simplified to the single 1 that "magically" is floating out to the left. For an explanation and proof of why flipping the MSB saves us the sign extension, see a computer arithmetic book[citation needed].

Implementations

Older multiplier architectures employed a shifter and accumulator to sum each partial product, often one partial product per cycle, trading off speed for die area. Modern multiplier architectures use the Baugh–Wooley algorithm, Wallace trees, or Dadda multipliers to add the partial products together in a single cycle. The performance of the Wallace tree implementation is sometimes improved by modified Booth encoding one of the two multiplicands, which reduces the number of partial products that must be summed.

Example

2 Bit by 2 Bit Binary Multiplier

See also

References

  1. ^ "The Evolution of Forth" by Elizabeth D. Rather et. al. [1] [2]
  2. ^ "Interfacing a hardware multiplier to a general-purpose microprocessor"
  • Computer Architecture: A quantitative Approach, Hennessy and Patterson, 1990, Morgan Kafmann Publishers, Inc. Section A.2 (pages A-3 through A-6) and section A.9 (pages A-39 through A-49).

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Multiplier — The term multiplier may refer to: In electrical engineering: Binary multiplier, a digital circuit to perform rapid multiplication of two numbers in binary representation Analog multiplier, a device that multiplies two analog signals Frequency… …   Wikipedia

  • Binary code — The word Wikipedia represented in ASCII binary. A binary code is a way of representing text or computer processor instructions by the use of the binary number system s two binary digits 0 and 1. This is accomplished by assigning a bit string to… …   Wikipedia

  • Binary prefix — Prefixes for bit and byte multiples Decimal Value SI 1000 k kilo 10002 M mega …   Wikipedia

  • Binary option — In finance, a binary option is a type of option where the payoff is either some fixed amount of some asset or nothing at all. The two main types of binary options are the cash or nothing binary option and the asset or nothing binary option. The… …   Wikipedia

  • Binary-phase shift keying — Phase shift keying Traduction terminée Phase shift keying → …   Wikipédia en Français

  • Binary phase-shift keying — Phase shift keying Traduction terminée Phase shift keying → …   Wikipédia en Français

  • List of 7400 series integrated circuits — The following is a list of 7400 series digital logic integrated circuits. The 7400 series originated with TTL integrated circuits made by Texas Instruments. Because of the popularity of these parts, they were second sourced by other manufacturers …   Wikipedia

  • Multiplication algorithm — A multiplication algorithm is an algorithm (or method) to multiply two numbers. Depending on the size of the numbers, different algorithms are in use. Efficient multiplication algorithms have existed since the advent of the decimal system.… …   Wikipedia

  • Multiplication ALU — In digital design, a multiplier or multiplication ALU is a hardware circuit dedicated to multiplying two binary values. A variety of techniques can be used to implement a digital multiplier. Most techniques involve computing a set of partial… …   Wikipedia

  • Booth's multiplication algorithm — is a multiplication algorithm that multiplies two signed binary numbers in two s complement notation.ProcedureBooth s algorithm involves repeatedly adding one of two predetermined values A and S to a product P , then performing a rightward… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”