Ford Straight-6 engine

Ford Straight-6 engine
170 Ford straight-6 in a 1962 Ford Falcon
Manufacturer Ford Motor Company
Production 1941 - 1996 (US)
1960 - present (AUS)
1961 - 1991 (ARG)
Cylinder block alloy Cast iron
Cylinder head alloy Cast iron
Valvetrain OHV
Fuel system Normally aspirated and Turbo charged
Fuel type Gasoline
Cooling system Watercooled

Ford's first straight-6 engine was introduced in 1906 in the Model K. Production ended in 1907. Henry Ford did not like this car, which could overpower its transmission. The next Ford six was introduced in the 1941 Ford. The Ford Motor Company of America continued producing straight six engines until they were replaced in the mid-1990s by more compact, less smooth V6 designs. However, Ford's Australian branch still manufactures these engines for their Falcon range.


First generation

The first generation Ford in-line six-cylinder (L6) engines were all of the flathead type. They were the G- and H-series engines of 226 cu in (3.7 L) used in cars and trucks and the M-series of 254 cu in (4.2 L) used in larger Ford trucks and for industrial applications.


Introduced with the 1941 model year, the first Ford six (designated G-series) displaced 226 cu in (3.7 L) and produced 90 hp (67 kW), the same as the Flathead V-8 that year. Like the V-8, it was also a flathead or L-head engine. In 1948, Ford raised the compression of the flathead six (designated H-series or Rouge 226) so that it generated 95 hp (71 kW) and 180 lb·ft (244 N·m) of torque. The G- and H-series engines were used in the full-size Ford cars and trucks to replace the smaller 136 cu in (2.2 L) Flathead V8 that were used with the 1937 Ford. Ford discontinued production of the H-series engine with the 1951 model year.


A 254 cu in (4.2 L) version of the flathead six (designated the M-series or Rouge 254) was used from 1948-53 in F6-series Ford trucks (COE, Dump, semi-, etc.), and small Ford school buses. The M-series engine produced 115 hp (86 kW) and 212 lb·ft (287 N·m). of torque. They were also used in miscellaneous industrial applications. e.g., to power water pumps for irrigation purposes and within wine-producing farms to manage risk by powering giant frost-control propellers on stands in the middle of rows of grapes.

Second generation

The second generation was produced from 1952 through 1964 and shared many parts with Ford Y-blocks such as the entire valve train and the problems associated with the Y-block's lubrication system. These engines have the exhaust and intake on the driver's side and the distributor on the passenger side making them easy to differentiate from the 240/300's.


A completely new OHV six was offered for the 1952 F-series. It displaced 215 cu in (3.5 L) and produced 101 hp (75 kW). It was also used in the 1952 Ford full-size cars.


The 215 grew to 223 cu in (3.7 L) for the 1954 F-series. Output was now 115 hp (86 kW) (as the "Mileage Maker" in the trucks) and 120 hp (89 kW) in the 1955 Ford cars. Power was up to 137 hp (102 kW) in the 1956 trucks.


A 262 cu in (4.3 L) version was also produced. The 262 was built from 1961-64 for use in heavy duty Ford trucks. This engine was also used for industrial applications.

Third generation

Thriftpower Six
Also called Falcon Six
Production 1960 - 1984
Power output 88 hp (66 kW) - 155 hp (116 kW)
Dry weight 385 lb (175 kg)

The third generation was produced at the Lima Engine plant in Lima, Ohio from 1960 through 1984. Officially dubbed the Thriftpower Six, this engine line is sometimes referred to as the Falcon Six. Note: Car companies including Ford, switched from gross ratings to net horsepower and torque ratings in 1972 (mainly because of the emissions laws being enacted nationwide at the time). Changes in engine compression and emissions controls make it difficult to compare engines from various production years (especially pre-1972).


140 Thriftpower Six
Production 1960 - 1964
Displacement 144 cu in (2.4 L)
Cylinder bore 3.5 in (89 mm)
Piston stroke 2.5 in (64 mm)
Compression ratio 8.7:1
Power output 84 hp (63 kW) @ 4200 RPM
Torque output 134 lb·ft (182 N·m) @ 2000 RPM

The 144 cu in (2.4 L) engine was first introduced in the 1960 Ford Falcon. The 144 was made from 1960 through 1964 and averaged 90 hp (67 kW) during the production run. While not known for being powerful or a stout engine, it proved to be economical and could get fairly good gas mileage for the time (up to 25-30mpg). This small six was the basis for all the Ford "Falcon" straight-six engines. The intake manifold on this series of engine was cast integrally with the cylinder head (this design was also used by Chevrolet with their third generation inline six); as a result, they could not be easily modified for greater power. This engine had four main bearings and can be identified by the three core plugs on the side of the block.

This engine was used in:


170 Thriftpower Six
170 Ford six in a 1966 Ford Mustang
Production 1961 - 1972
Displacement 170 cu in (2.8 L)
Cylinder bore 3.5 in (89 mm)
Piston stroke 2.94 in (75 mm)
Compression ratio 9.1:1
Power output 105 hp (78 kW) @ 4400 RPM
Torque output 156 lb·ft (212 N·m) @ 2400 RPM

In 1961 the 170 cu in (2.8 L) became an option for the Falcon line. The 170 was a stroked version of the 144, changing the stroke from 2.5" to 2.94". The original 1964½ Ford Mustang used a 101 hp (75 kW) version. The Econoline van and Ford Bronco received a heavier duty version with mechanical valve lifters. This engine had four main bearings and can be identified by the three freeze (core) plugs on the side of the block. The 170 was dropped from production in 1972.


The 200 engine model was introduced in the middle of 1963 and shared the four main bearing design used in the 170 engine. Early 200s can be identified by three freeze (core) plugs on the side of the block.

Beginning in 1965 the 200 CID engines were upgraded to seven main bearings to reduce harmonic vibrations and increase durability. The 1965 and later engine can be identified by 5 freeze (core) plugs on the side of the block and the casting code C5DE-H. Starting in 1966 a six bolt bell housing flange block was introduced.

Beginning in 1980 the block was redesigned with a bell housing flange and a low mount starter that is very similar to the small block Ford V8. This version is easily identified by its low-mounted starter location down by the oil pan rail and is referred to as the Big Bell 200. The big bell design is uncommon but sought after by Inline six performance enthusiasts because it can be modified to accept a Ford small block V8 six bolt bell housing.

The 1965 Mustang used this engine as standard with 120 hp (89 kW). The Mustang continued to use the 200 as its base engine until it was dropped in 1971.

When Ford launched the third generation Fox body Mustang in 1979, the original engine line up included the Cologne V6. The same engine was also offered in the hugely successful Ford of Europe Capri Mk II. The 2.8L V6 engine was a popular option for the US Mustang and the European Capri MkII and as a result the Cologne engine plant could not meet the demand for engines for both Continents.

So, the Cologne 2.8L V6 was dropped from the engine lineup in the middle of the 1979 production year and replaced with the 200cid Falcon inline six, which was now referred to as the 3.3L engine. The engine and front suspension K-member was transferred from the Fairmont model which helped reduce costs instead of having to redesign the Mustang for a different engine.

The 200 was used in the Ford Maverick and Mercury Comet models, and continued in the Ford Fairmont and Mercury Zephyr until the Fairmont and Zephyr models were retired at the end of the 1983 model year and replaced with the Ford Tempo and Mercury Topaz.

The Ford Granada and Mercury Monarch offered the 200 inline six as part of their engine lineup from 1975 to 1982 when they were replaced in 1983 by the Ford LTD and the Mercury Marquis. These two models used the engine from 1983 to 1984 when it was replaced by the 3.8L Essex V6.

Ford was also having problems meeting demand for its 2.3L OHC engine which was used in a multitude of models worldwide.

In anticipation of another engine shortage, Ford's Lima Ohio engine plant, which was already producing the 2.3L OHC engine, decided they could modify the Falcon inline six block casting molds to remove cylinders 4 and 5 to create a 4 cylinder engine. An aluminum high-swirl cylinder head (actually it was cast iron) was developed, and the motor was designated the 2.3L HSC to help differentiate it from the same displacement 2.3L OHC design. This motor shared many common parts with the 200/3.3L inline six, and it is common for persons rebuilding their 200/3.3L inline six motors to use the 2.3L HSC pistons as a cheap replacement.


The 250 cu in (4.1 L) straight six was an engine option offered in 1969 in the Mustang, and 1970 in medium-sized Ford cars (Maverick). The 250 was a stroked 200, made by changing the stroke from 3.126" to 3.91". Output was 155 hp (115 kW) in the Mustang, and became the base engine in 1971. Power was re-evaluated at 98 hp (73 kW) for 1972 (due to power rating changes) and 88 hp (66 kW) the next year. The last year of production for the 250 was 1980. This engine had seven main bearings, and can be identified by the five freeze (core) plugs on the side of the block. The block uses a low mount starter and six bellhousing bolts, sharing its bellhousing with the Windsor V-8s 302-351W, late (1965–68) 289, 351 Cleveland, early 4.6, and the 240-300 CID Ford Six.

Restoration and restomod status

The rising cost of fuel has increased the interest in the Falcon six design, and the engines have been gaining in popularity in recent years. Many Falcon and Mustang owners who used to replace their car's original inline six engine with a V8, are now keeping their inline sixes for the better fuel economy the inline six motor offers. A number of restoration and performance parts vendors now stock parts for people restoring their inline six motors.

Due to increased popularity of the Falcon six engine, the desire for improved performance, and difficulty in finding good quality used parts for an engine that has been out of production for 25 years, in 2005 the company Classic Inlines designed a modern aluminum head based on the Australian 250-2v head but with raised intake ports, high swirl combustion chambers, and larger valves. One of the features of the new head are pads cast into the top of the intake runners, which allows owners the ability to machine the head to accept modern electronic fuel injectors for direct port fuel injection.

Not only does the new head improve power output, but also the high-swirl design improves fuel mixing in the cylinder for a more complete burning of the air fuel mixture, resulting in reduced emissions output.

Ford of Australia inline six

Starting in 1960, Ford of Australia used the same inline six engines as North America, featuring the 144 cid and 170 cid models. Also as in North America, a 200 cid motor was added in 1965. The 144 cid motor was discontinued in late 1966.

In 1968, Ford of Australia increased the deck height of the design to make room for increased crankshaft stroke, resulting in displacements of 188 cid and 221 cid (badged 3.1 and 3.6 litres). They superseded the 170 cid and 200 cid motors in the lineup.

In 1970, Ford of Australia enlarged the motors to 200 cid & 250 cid. The head was of the same design as previous models, with an integral intake catering for 1 single barrel Bendix-Stromberg carburettor. In the configuration, the Falcon 250 cid six was rated at 155 hp (116 kW). Around this time Ford of Australia also developed the '2V' cylinder head, which in all respects was similar to the previous integral "log head" intake, with the exception of a removable aluminum intake which mounted a Bendix-Stromberg WW 2-barrel carburettor. To take advantage of the much improved breathing ability that the removable intake brought to the new head, the 250-2V also featured a much better breathing exhaust manifold. The result was the engine being rated at 170 hp (127 kW).

For years the 250-2V cylinder head was very popular for racing and many have been imported to North America, where owners of cars with the Falcon inline six have upgraded their engines with the better cylinder head.

In 1976, Ford of Australia updated the engines with a new cast iron crossflow head design. Engine displacements remained 200 cid and 250 cid, but were now badged 3.3 and 4.1 litres respectively. These engines were offered in the Ford Falcon XC in Australia. Whereas the previous integral "log head" inline six motor borrowed from the Ford FE engine family design, the new crossflow motor borrowed from the Ford 351 Cleveland engine family. A common upgrade for a crossflow head engine is to use 351 Cleveland roller tip rocker arms.

Ford of Australia updated the crossflow design in mid-1980 with a new aluminum head casting. The alloy head was used to improve warm up time and reduce fuel consumption and emissions. Up until 1982, the engines were fitted with a single barrel Bendix-Stromberg carburetor, but from March 1982 were fitted with a Weber 2-barrel carburetor, which had improved fuel consumption over the single barrel carb. The Weber carburettored engines were badged Alloy-Head II

Later, a Bosch Jetronic fuel injected version with direct port fuel injection was offered in the XE Falcon, and was only available as an aluminium 4.1 L. The XF Falcon's 4.1 then received Ford's EEC-IV engine management system with Multi Point EFI (The carburetor engine was still fitted standard, and EFI was optional). There were changes to the carburetor-based engine to accommodate the Electronic Fuel Injection system. The compression ratio on the 4.1 L was 8.89:1. The cylinder head intake ports had been modified to provide clearance for the injectors, and a new intake manifold was designed and many other changes were made in the engine bay to accommodate the new fuel system.

  • Power at specified RPM (DIN) Pre '86 running on leaded fuel
    • 3.3 L 90 kW (121 hp) @ 4100 rpm
    • 4.1 L carburetor 103 kW (138 hp) @ 3750 rpm
    • 4.1 L E.F.I engine 120 kW (161 hp) @ 4000 rpm
  • Torque at specified RPM (DIN) Pre '86 running on leaded fuel
    • 3.3 L 240 N·m (180 lb·ft) @ 2500 rpm
    • 4.1 L carburetor 316 N·m (233 lb·ft) @ 2400 rpm
    • 4.1 L E.F.I engine 333 N·m (246 lb·ft) @ 3000 rpm
  • Power at specified RPM (DIN) ADR 37 compliant engine running on unleaded fuel
    • 3.3 L 89 kW (119 hp) @ 4000 rpm
    • 4.1 L Carburetor 99 kW (133 hp) @ 3600 rpm
    • 4.1 L E.F.I engine 123 kW (165 hp) @ 4000 rpm
  • Torque at specified RPM (DIN) ADR 37 compliant engine running on unleaded fuel
    • 3.3 L 238 N·m (176 lb·ft) @ 2200 rpm
    • 4.1 L carburetor 303 N·m (223 lb·ft) @ 2000 rpm
    • 4.1 L E.F.I engine 328 N·m (242 lb·ft) @ 3000 rpm

In 1988, the inline six engines underwent a major redesign for the EA Falcon and now featured a new single overhead cam (SOHC) crossflow aluminum head. The camshaft and auxiliary shaft are driven by a 'duplex' chain. The duplex chain drives the distributor and the oil pump shafts. The camshaft is supported on the cylinder head by using 'topless' bearings. Bearing liners are not used. The camshaft is held in position using valve spring pressure. Hydraulic lash adjusters mounted on the rocker arms are used to provide zero valve lash. As with all previous and current models, the block is cast iron, but with a reduction in the cylinder bore to try to help reduce emissions.

The SOHC engines were offered as the 3.2L (with throttle body injection) and the 3.9L (with throttle body or multipoint fuel injection). In 1989, the 3.2L TBI version was discontinued, and in 1991 the 3.9L's displacement was enlarged to 4.0L (now only with MPI) and was rated at 148 kW (198 hp). 1995 saw the introduction of the dual resonance intake manifold for the EF series. Also for the EF series Falcon, the standard engine employed a high-energy coil-pack ignition system. However, the EL Falcon used a distributor/coil ignition setup, as in Falcon models prior to EF.

Ford of Australia redesigned the inline six again in 1998, and increased the main bearing size and added a ladder style main stud girdle integral with the oil pan to increase low end rigidity. The engine also received variable cam timing technology, which can advance or retard cam timing depending on engine rpm, which gives a much broader power band.

In 2002 the engine received double overhead cams (DOHC) with variable cam timing as the Barra inline six motors and, depending on the version of engine, were offered in the 2002 BA Falcon, Fairlane, and the SX Territory. Currently the BA 195 powers the Falcon and Falcon "Utes" (since 2008) along with the SZ Territory (since 2011). The BA195 is rated at 261 hp (195 kW) @ 6000 rpm and 391 N·m (288 lb·ft) lbs @ 3250 rpm whilst the BA 190 is rated at 255 hp (190 kW) @ 5250rpm and 383 N·m (282 lb·ft) @ 2500rpm. All DOHC engines feature the coil on plug direct ignition system.

There have been some noteworthy performance versions of the DOHC Barra inline sixes.

The Barra 240T, which was a turbocharged, fuel injected, intercooled DOHC inline six producing 322 hp (240 kW) and 332 ft (101 m) lbs of torque, was offered between 2002 and 2005 in the BA Falcon XR6 and XR6 Turbo as well as the Territory Turbo. This was followed in the BF & BF Mk II (between 2005 and 2008) by the Barra 245T producing 329 hp (245 kW) of power and 480 N·m (350 lb·ft) of torque which in turn was followed in the FG (since 2008) by the Barra 270T producing 362 hp (270 kW) of power and 533 N·m (393 lb·ft) of torque.

Ford Australia's high-performance division FPV created even more powerful Turbocharged model variants which were upgraded largely co-inciding with the upgrades of the regular Falcon. The first Turbocharged Straight-6 engined car from FPV was the BA Mk II F6 (2004–2005) which produced 362 hp (270 kW) of power and 550 N·m (410 lb·ft) of torque. The BF (2005–2006) and BF Mk II (2006–2008) F6's had the same power and torque figures. The first power and torque upgrade came with the current FG model which has 416 hp (310 kW) of power @ 5500rpm and 565 N·m (417 lb·ft) of torque. The Barra 310T is the first Australian-built motor to achieve over 100 hp per litre, and until the release of the new Ford supercharged "Miami" V8, produced more torque than any Australian-built engine to date.

Nizpro Turbocharging, based in Victoria, Australia, with their roots in Nissan engines, turned their attention to the Barra engine and were the first to extract 1,000 hp (746 kW) reliably from a Barra 240T engine in 2004, with carefully designed cams, manifolds and turbocharger. With Motec engine management the engine rev limit was increased to 7200RPM and it produced 1,000 N·m (740 lb·ft) of torque at only 3500RPM. A custom crank, conrods and pistons were used but the cylinder head was left unmodified apart from the camshafts and valve springs. The engine was available for order to be built by the public, but at a price tag of over AU$38,000

Ford of Australia had intended to discontinue production of the inline six motors at their Geelong engine plant in 2010, and replace them with imported Duratec V6s from North America. Due to the drastic increase of oil prices in 2008 and the following economic turmoil, the decision was reversed. Instead, Ford of Australia announced on 20 November 2008 that 21 million Au dollars would be invested in the Geelong engine plant to bring the inline six engines up to date with the current Euro IV emissions standards.

Falcon model Capacity Induction Valvetrain Fuel Power Torque Notes
XY, XA, XB 4.1 L Carburettor OHV Leaded 116 kW (156 hp) 325 N·m (240 lb·ft)
XC 4.1 L Carburettor OHV Leaded 92 kW (123 hp) 289 N·m (213 lb·ft) Crossflow cylinder head
XD 4.1 L Carburettor OHV Leaded 94 kW (126 hp) 305 N·m (225 lb·ft)
XE 4.1 L EFI OHV Leaded 111 kW (149 hp) 325 N·m (240 lb·ft) Bosch LE II Jetronic fuel injection
XF 4.1 L EFI OHV Unleaded 121 kW (162 hp) 325 N·m (240 lb·ft) Ford EEC-IV Multi Point EFI
EA, EB 3.9 L EFI SOHC Unleaded 120 kW (161 hp) 311 N·m (229 lb·ft)
EA, EB 3.9 L EFI SOHC Unleaded 139 kW (186 hp) 338 N·m (249 lb·ft) EEC-IV Multi-point injection
EB series II, ED 4.0 L EFI SOHC Unleaded 148 kW (198 hp) 348 N·m (257 lb·ft)
XR6 ED, EF, EL 4.0 L EFI SOHC Unleaded 164 kW (220 hp) 366 N·m (270 lb·ft)
EF, EL, AU 4.0 L EFI SOHC Unleaded 157 kW (211 hp) 357 N·m (263 lb·ft) Coil-pack ignition system (EF and AU Only)
AU series II and III 4.0 L EFI SOHC LPG 143 kW (192 hp) 362 N·m (267 lb·ft) Dedicated LPG
XR6 AU 4.0 L EFI SOHC Unleaded 172 kW (231 hp) 374 N·m (276 lb·ft) VCT Variable Valve Timing
BA 4.0 L EFI DOHC Unleaded 182 kW (244 hp) 380 N·m (280 lb·ft)
BA XR6 Turbo 4.0 L EFI DOHC Unleaded 240 kW (322 hp) 450 N·m (332 lb·ft) Garrett GT3540 turbocharger
BF 4.0 L EFI DOHC Unleaded 190 kW (255 hp) 383 N·m (282 lb·ft)
BF XR6 Turbo 4.0 L EFI DOHC Unleaded 245 kW (329 hp) 480 N·m (354 lb·ft) Garrett GT3540 turbocharger
FG 4.0 L EFI DOHC Unleaded 195 kW (261 hp) 391 N·m (288 lb·ft)
FG XR6 Turbo 4.0 L EFI DOHC Unleaded 270 kW (362 hp) 533 N·m (393 lb·ft)
FPV F6 model Capacity Induction Valvetrain Fuel Power Torque Notes
BA MkII, BF 4.0 L EFI DOHC Unleaded 270 kW (362 hp) 550 N·m (406 lb·ft)
FG 4.0 L EFI DOHC Unleaded 310 kW (416 hp) 565 N·m (417 lb·ft)

Fourth generation

Truck Six
Production 1964 - 1996
Displacement 240 cu in (3.9 L)
300 cu in (4.9 L)
Cylinder bore 4"
Piston stroke 3.18" (240)
3.98" (300)
Fuel system Normally aspirated
Fuel injection
Power output 120 hp (89 kW) - 170 hp (127 kW)
Torque output 260 lb·ft (353 N·m)

Produced at the Cleveland Engine plant in Brook Park, Ohio from 1964 through 1996, the 240 and 300 Sixes are well-known for their durability. Simple design and rugged construction continue to endear these engines to a number of Ford enthusiasts to this day. Many have run 300,000 to 600,000 miles (480,000 to 970,000 km) without any more service than standard oil changes.[citation needed] The engine has earned the terms "bulletproof" and "indestructible" by many. There are numerous claims of those who have purposely sought out to destroy one through abusive use, and were unsuccessful in doing so.

One example of the engine's sturdy design is the fact that no timing chain or timing belt (both of which can break, causing unwanted downtime or even engine damage) is used. This generation of Ford Six was designed with long-wearing gears for that purpose instead. Very few modern engines use timing gears; belts and chains are by far more common.

Both the 240 and the 300, no matter the application, used a single barrel Carter YF carburetor until the introduction of Electronic Fuel Injection. With proper gearing, many F-trucks and Broncos are able to achieve over 20 mpg with these carburetors, when properly tuned. This was heavily used by Ford's advertising campaign (some television advertisements and written literature even claimed 30 mpg), since the V8 engines in these trucks rarely achieved over 14 mpg.

The fuel economy of the 300 makes the engine a popular choice amongst truck enthusiasts that want both power and economy. The addition of performance parts (such as intake and exhaust manifolds with a four barrel carburetor) place the engine power output near the same levels as the stock HO (high output) version of the optional 351 V8, with little or no change in economy. There are claims of 300s that have had the power output doubled, or even tripled, with less than a single mpg drop in fuel economy.


The 240 cu in (3.9 L) six for 1965 – 1970 full sized cars (continued to 74 in fleet models) and 63-77 trucks produced 150 hp (112 kW). In stationary service (generators and pumps) fueled by LPG or natural gas, this is known as the CSG-639. The 240 had a bore of 4" and a stroke of 3.18".


The 300 cu in (4.9 L) six was added for the F-series in 1965. It was essentially a 240 cu in (3.9 L) with a longer stroke. The two engines are nearly identical; the differences are in block dimensions, combustion chamber size, and the rotating assembly. It produced 170 hp (127 kW) (gross). The 300 became the base F-series engine in 1978 at 114 hp (85 kW) (hp number changes due to Ford switching to net power ratings in 1971). Power outputs were increased to roughly 122 hp (91 kW) during the early 1980s, before fuel injection was introduced. This became the primary engine of the line, eclipsing the 240. Unlike the Falcon engine, it featured separate intake and exhaust manifolds, which could be easily replaced with aftermarket manifolds offering the promise of even more power, through the installation of larger carburetors and a higher flowing exhaust system.

Also during the late sixties and early seventies, the 300 was used in larger vehicles such as dump trucks, many weighing into the 15,000–20,000 pound (7,000–9,000 kg) range. These 300s were equipped with a higher flow HD (Heavy Duty) exhaust manifold, since the engines were going to be constantly working in the 3000–4000 rpm range. These rare, yet effective manifolds had higher flow than the electronic fuel injection 4.9 (300) manifolds and some headers.

Engine sizes were converted to metric for 1983, causing the 300 to become the "4.9". Fuel injection and other changes in 1987 pushed output up to 165 hp (123 kW) with 8.8:1 compression. This engine was gradually phased out, ending production in 1996, and was replaced by the Essex V6 in the F-series trucks with their 1997 redesign. However, it was renowned for its durability, low end torque, and ease of service. The 300 4.9 came with the Ford C6, E4OD, ZF S5-42 and S5-47 transmissions, as well as the Mazda built M5OD 5 speed manual transmission, and the Borg-Warner T18 and New Process NP435 4 speed manual transmissions. The 4.9 liter 6 cylinder was built in the Cleveland, Ohio engine plant.

This engine is also used by Stewart and Stevenson in the MA Baggage Tow Tractor (pdf), and Harlan in their standard tow tractors [1], as well as a multitude of other pieces of equipment, such as ski lifts, power generators, wood chippers, tractors, and, until they converted to diesel engines, most UPS trucks. Many UPS trucks still use the 300 to this day.

In stationary service (generators and pumps) fueled with LPG or natural gas, this engine is known as the CSG-649.

The Ford Inline six in racing

The Ford Inline six has had a small though colorful career in racing, which has increased in recent years due to the rising popularity of the motor and the availability of performance parts. The big 240's and 300's offered stronger torque at lower engine speed than most V8's of comparable displacement, while sacrificing peak power because of their square bore/stroke. The long stroke combined with the longer crankshaft creates problems at higher engine speed, and most stock cast iron pieces are not recommended for service above 5000 rpm. The engine also weighs more than a V8 of similar displacement due to the longer length. The most desirable engines are those from mid-1960s dump trucks, as they have forged steel crankshafts and high-flow exhaust manifolds.[1]

A recent yet giant step in Ford Inline six racing has been performed by McLearran Motorsports in Tucson AZ. The McLearrans, Wil and Kelly, have achieved enough notice that their 1963 Ford Falcon has been seen in several magazines and was scheduled to make an appearance on the show Pinks.

The 1963 Falcon driven by McLearran Motorsports' Kelly McLearran has been dyno tested at 323 rwhp @ 4500 rpm and 502 rwtq @ 2650 rpm. The car has run a best time of 10.89 seconds at 1/4 mile, with Kelly driving.


External links

Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • Ford Power Stroke engine — Infobox Automobile engine name=Ford Power Stroke engine aka=International Truck and Engine Corporation manufacturer=Navistar Inc. production=1994 ndash; class=OHV 90° V8 Diesel predecessor= similar=Duramax V8 B series I6Introduced in mid 1994… …   Wikipedia

  • Ford Essex V6 engine (Canadian) — See also Ford Essex V6 engine (UK) Infobox Automobile engine name = Essex manufacturer = Ford Motor Company type = 90° V6 bore = 3.811 in (96.8 mm) stroke = 3.386 in (86 mm) 3.46 in (87.9 mm) 3.74 in (95 mm) displacement = 232 in³ (3797 cc) 238… …   Wikipedia

  • Chevrolet Straight-6 engine — Straight 6 Manufacturer General Motors Corporation Production 1929 1990 North America 2002 2009 (Atlas LL8) North America 1962 1999 Brazil Predecessor 171 Straight 4 Successor GM Atlas engine Valvetrain …   Wikipedia

  • Pontiac Straight-8 engine — Infobox Automobile engine name=Pontiac straight 8 engine aka= Silver Streak production=1933 ndash;1954 manufacturer=General Motors type=8 cylinder flathead predecessor=Auto CID|251 flathead V8 successor=Auto CID|287 OHV V8The straight 8 was an… …   Wikipedia

  • Ford Falcon (Argentina) — Infobox Automobile name = Ford Falcon manufacturer = Ford Motor Company of Argentina class = Full size production = 1963 1991 assembly = General Pacheco body style = 4 door sedan 5 door station wagon 2 door ute The Argentinian Ford Falcon is a… …   Wikipedia

  • Ford F-Series — Ford F Series …   Википедия

  • Ford Capri — was a name used by the Ford Motor Company for three separate automobile models: * The Ford Consul Capri coupe, produced by Ford of Great Britain between 1961 and 1964 * The Ford Capri coupe, produced by Ford Europe from 1969 to 1986 * The Ford… …   Wikipedia

  • Ford Duratec engine — Manufacturer Ford Production 1993–present Displacement 1.3 L (79 CID) 1.4 L 1.6 L (97 CID) 1.8 L (110 …   Wikipedia

  • Ford Cortina — Manufacturer Ford Motor Company Hyundai Motor Company Also called Ford Consul Cortina Production 19 …   Wikipedia

  • Ford Zephyr engine — Ford s revolutionary United Kingdom Zephyr/Consul cars used a new family of engines. The so called Zephyr engine included both straight 4 and straight 6 OHV engines. Production began in 1951 and lasted through to 1966.Consul/Zephyr 4The straight… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”