Spark-gap transmitter

Spark-gap transmitter

A spark-gap transmitter is a device for generating radio frequency electromagnetic waves. These devices served as the transmitters for most wireless telegraphy systems for the first three decades of radio (1887–1916) and the first demonstrations of practical radio were carried out using them. In later years more efficient transmitters were developed based on high-speed Alexanderson alternators and Poulsen Arc generators, but spark transmitters were still preferred by most operators. This was because of both their uncomplicated design and the fact that the transmitter stopped generating a carrier as soon as the Morse Code key was released, allowing the operator to "listen through" for a reply. With the other types of transmitter, the carrier wave could not be controlled so easily, and elaborate measures were required both to modulate the carrier and to separate the receiving antenna from the transmitting antenna. After WWI, greatly improved vacuum tube transmitters became available which overcame these problems, and by the late 1920s the only spark transmitters still in operation were "legacy" installations on Naval vessels. Even when vacuum tube based transmitters had been installed, many vessels retained their crude but reliable spark transmitters as an emergency backup, but by 1940, the technology was no longer used. Use of the spark-gap transmitter has led to many radio operators being nicknamed "Sparks" even long after the transmitters were no longer in use.


The history of radio shows that the spark gap transmitter was the product of many people, often working in competition. In 1862 James Clerk Maxwell predicted the propagation of electromagnetic waves through a vacuum.

In 1887, David E. Hughes used a Spark Gap to generate radio signals, achieving a range of approximately 500 metres.

In 1888 physicist Heinrich Hertz set out to verify Maxwell's predictions. Hertz used a tuned spark gap transmitter and a tuned spark gap detector (consisting of a loop of wire connected to a small spark gap) located a few meters away. In a series of UHF experiments, Hertz verified that electromagnetic waves were being produced by the transmitter. When the transmitter sparked, small sparks also appeared across the receiver's spark gap, which could be seen under a microscope.

Nikola Tesla introduced his radio system in 1893 and later developed the so-called "loose coupler" system which produced a far more coherent carrier wave, produced far less interference, worked with much greater efficiency, and could be operated in any weather conditions.

Tesla pursued the application of his high voltage high frequency technology to radio. By tuning a receiving coil to the specific frequency used in the transmitting coil, he showed that the radio receiver's output could be greatly magnified through resonant action. Tesla was one of the first to patent a means to reliably produce radio frequencies (eg., US patent|447920, "Method of Operating Arc-Lamps" (March 10, 1891)). Tesla also invented a variety of rotary, cooled, and quenched spark gaps capable of handling high power.

Marconi began experimenting with wireless telegraphy in the early 1890s. In 1895 he succeeded in transmitting over a distance of 1 1/4 miles. His first transmitter consisted of an induction coil connected between a wire antenna and ground, with a spark gap across it. Every time the induction coil pulsed, the antenna would be momentarily charged up to tens (sometimes hundreds) of thousands of volts until the spark gap started to arc over. This acted as a switch, essentially connecting the charged antenna to ground, producing a very brief burst of electromagnetic radiation.

While this worked well enough to prove the concept of wireless telegraphy, it had some severe shortcomings. The biggest problem was that the maximum power that could be transmitted was directly determined by how much electrical charge the antenna could hold. Because the capacitance of practical antennas is quite small, the only way to get a reasonable power output was to charge it up to very high voltages. However, this made transmission impossible in rainy or even damp conditions. Also, it necessitated a quite wide spark gap, with a very high electrical resistance, with the result that most of the electrical energy was used simply to heat up the air in the spark gap.

The other problem was that, due to the very brief duration of each burst of electromagnetic radiation, the system radiated an extremely "dirty" signal sideband-wise, which was almost impossible to tune out if the listener wanted to monitor a different station. Despite this, Marconi was able to establish a commercial wireless telegraph service that served the United States and Europe.

Reginald Fessenden's first attempts to transmit voice employed a spark transmitter operating at approximately 10,000 sparks/second. To modulate this transmitter he inserted a carbon microphone in series with the supply lead. He experienced great difficulty in achieving Intelligible sound.

In 1905 a "state of the art" spark gap transmitter generated a signal having a wavelength between 250 meters (1.2 MHz) and 550 meters (545 kHz). 600 meters (500 kHz) became the International distress frequency. The receivers were simple unamplified detectors, usually coherers (small quantity of metal filings lying loosely between metallic electrodes). This later gave way to the famous and more sensitive galena crystal sets. Tuners were primitive or nonexistent. Early amateur radio operators built low power spark gap transmitters using the spark coil from Ford Model T automobiles. But a typical commercial station in 1916 might include a 1/2 kW transformer that supplied 14,000 volts, an eight section condenser, and a rotary gap capable of handling a peak current of several hundred amperes.

Shipboard installations usually used a DC motor (usually run off the ship's DC lighting supply) to drive an alternator whose output was then stepped up to 10,000 – 14,000 Volts by a transformer.

Spark gap transmitters generate fairly broad signals. As the more efficient transmission mode of continuous waves (CW) became easier to produce and band crowding and interference worsened, spark-gap transmitters and damped waves were legislated off the new shorter wavelengths by international treaty, and replaced by Poulsen arc converters and high frequency alternators which developed a sharply defined transmitter frequency. These approaches later yielded to vacuum tube technology and the 'electric age' of radio would end. Long after they stopped being used for communications, spark gap transmitters were employed for radio jamming. Spark gap oscillators are still used to generate high frequency high voltage to initiate welding arcs in gas tungsten arc welding [] . Powerful spark gap pulse generators are still used to simulate EMP. Most high power gas-discharge street lamps (mercury and sodium vapor) still use modified spark transmitters as switch-on ignitors.


thumb|right|333px|A typical spark transmitter circuit.">
capacitor - C1 and C2;
resistor - R;
inductor - L.
The spark transmitter is very simple in operation, but it presented significant technical problems mostly due to very large induced EMF when the spark struck, which caused breakdown of the insulation in the primary transformer. To overcome this the construction of even low-power sets was very solid. The damped wave output was very wasteful of bandwidth, and this limited the number of stations that could communicate effectively without interfering with each other.

In its simplest form, a spark-gap transmitter consists of a spark gap connected across an oscillatory circuit consisting of a capacitor and an inductor in series or parallel. In a typical transmitter circuit, a high voltage source (shown in the schematic as a battery, but usually a high voltage transformer) charges a capacitor (C1 in figure) through a resistor until the spark gap discharges, then a pulse of current passes through the capacitor (C2 in figure). The inductor and capacitor after the gap form a resonant circuit. After being excited by the current pulse, the oscillation rapidly decays because energy is radiated from the antenna. Because of the rapid onset and decay of the oscillation, the RF pulse occupies a large band of frequencies.

The function of the spark gap is to present initially a high resistance to the circuit to allow the capacitor to charge. When the breakdown voltage of the gap is reached, it then presents a low resistance to the circuit causing the capacitor to discharge. The discharge through the conducting spark takes the form of a damped oscillation, at a frequency determined by the resonant frequency of the LC circuit.

Spark gaps

A simple spark gap consists of two conducting electrodes separated by a gap immersed within a gas (typically air). When a sufficiently high voltage is applied, a spark will bridge the gap, ionizing the gas and drastically reducing its electrical resistance. An electric current then flows until the path of ionized gas is broken or the current is reduced below a minimum value called the 'holding current'. This usually occurs when the voltage across the gap drops sufficiently, but the process may also be assisted by cooling the spark channel or by physically separating the electrodes. This breaks the conductive of ionized gas, allowing the capacitor to recharge, and permitting the recharging/discharging cycle to repeat. The action of ionizing the gas is quite sudden and violent ("disruptive"), and it creates a sharp sound (ranging from a "snap" for a spark plug, a loud "bang" for a wider gap. The spark gap also liberates light and heat.


Spark gaps used in early radio transmitters varied in construction, depending on the power to be handled. Some were fairly simple, consisting of one or more fixed ("static") gaps connected in series, while others were significantly more complex. Because sparks were quite hot and erosive, electrode wear and cooling were constant problems. As transmitter power was increased, the problem of quenching also arose.

Quenching refers to the act of extinguishing the previously established arc within the spark gap. This is considerably more difficult than initiating spark breakdown in the gap. A cold, non-firing spark gap contains no ionized gases. Once the voltage across the gap reaches its breakdown voltage, gas molecules in the gap are very quickly ionized along a path, creating a hot electric arc, or plasma, that consists of large numbers of ions and free electrons between the electrodes. The arc also heats part of the electrodes to incandescence. The incandescent regions contribute free electrons via thermionic emission, and (easily ionized) metal vapor. The mixture of ions and free electrons in the plasma is highly conductive, resulting in a sharp drop in the gap's electrical resistance. This highly conductive arc supports efficient tank circuit oscillations. However, the oscillating current also sustains the arc and, until it can be extinguished, the tank capacitor cannot be recharged for the next pulse.

Quenching the arc

Several methods were applied to quench the arc.
*Jets of air that cool, stretch, and literally 'blow out' the plasma,
*multi-plate discharger of Max Wien to cool the arcs in medium power spark sets, known as the "whistling spark" for its distinctive signal,
*using a different gas, such as hydrogen, that quenches more efficiently by providing more effective electrode cooling,
*a magnetic field (from a pair of permanent magnets or poles of an electromagnets) oriented at right angles to the gap to stretch and cool the arc.

Rotary gaps

The need to extinguish arcs in increasingly higher power transmitters led to the development of the rotating spark gap. These devices were used with an alternating current power supply, produced a more regular spark, and could handle more power than conventional static spark gaps. The inner rotating metal disc typically had a number of studs on its outer edge. A discharge would take place when two of the studs lined up with the two outer contacts which carried the high voltage. The resulting arcs were rapidly stretched, cooled, and broken as the disk rotated.

Rotary gaps were operated in two modes, synchronous and asynchronous. A synchronous gap was driven by a synchronous AC motor so that it ran at a fixed speed, and the gap fired in direct relation to the waveform of the A.C. supply that recharged the tank capacitor. The point in the waveform where the gaps were closest was changed by adjusting the rotor position on the motor shaft relative to the stator's studs. By properly adjusting the synchronous gap, it was possible to have the gap fire only at the voltage peaks of the input current. This technique allowed the tank circuit to fire only at successive voltage peaks, thereby delivering maximum energy from the fully charged tank capacitor each time the gap fired. The "break rate" was thus fixed at twice the incoming power frequency (typically, 100 to 120 breaks/second). When properly engineered and adjusted, synchronous spark gap systems delivered the largest amount of power to the antenna. However, electrode wear would progressively change the gap's "firing point", so synchronous gaps were somewhat temperamental and difficult to maintain.

Asynchronous gaps were considerably more common. In an asynchronous gap, the rotation of the motor had no fixed relationship relative to the incoming AC waveform. Asynchronous gaps worked quite well and were much easier to maintain. By using a larger number of rotating studs or a higher rotational speed, many asynchronous gaps operated at break rates in excess of 400 breaks/second. Since the gap could be fired more often than the input waveform switched polarity, the tank capacitor was charged and discharged more rapidly than a synchronous gap. However, each discharge would occur at a varying voltage that was almost always lower than the consistent peak voltage obtained from a synchronous gap.

Rotary gaps also served to alter the tone of the transmitter, since changing either the number of studs or the rotational speed changed the spark discharge frequency which was audible in receivers with detectors that could detect the modulation on the spark signal. This enabled listeners to distinguish between different transmitters that were nominally tuned to the same frequency. A typical high-power multiple spark system (as it was also called) used a 9 to 24 inch diameter rotating commutator with six to twelve studs per wheel, typically switching several thousand volts. The output of rotary spark gap transmitter was turned on and off by the operator using a special kind of telegraph key that switched power going to the high voltage power supply. The key was designed with large contacts to carry the heavy current that flowed into the low voltage (primary) side of the high voltage transformer (often in excess of 20 amps).

External links

* [ Alternator, Arc and Spark]
* [ Fessenden and the Early History of Radio Science]
* [ Brief history of spark]
* [ Massie Spark Transmitter] The new England Wireless and Steam Museum
* [ The Sounds of a Spark Transmitter with audio]
* [ Russ Kleinman's web site devoted to Spark Keys and Spark Transmitters - has virtual spark transmitter]

Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Spark gap — A spark gap consists of an arrangement of two conducting electrodes separated by a gap usually filled with a gas such as air. When a suitable voltage is supplied, a spark forms, ionizing the gas and drastically reducing its electrical resistance …   Wikipedia

  • spark transmitter — n. an early type of radio transmitter that uses the oscillatory discharge of a capacitor through an inductor in series with a spark gap to generate its high frequency power …   English World dictionary

  • spark transmitter — noun an early radio transmitter using a discharge across a spark gap as the source of its power • Hypernyms: ↑radio transmitter * * * noun : a radio transmitting set using a spark generator * * * Radio. a transmitting set that generates… …   Useful english dictionary

  • Transmitter — For biologic transmitters, see transmitter substance. Commercial FM broadcasting transmitter at radio station WDET FM, Wayne State University, Detroit, USA. It broadcasts at 101.9 MHz with a radiated power of 48 kW. In electronics and… …   Wikipedia

  • spark transmitter — Radio. a transmitting set that generates electromagnetic waves by the oscillatory discharge from a capacitor through an inductor and a spark gap. [1915 20] * * * …   Universalium

  • spark transmitter — /ˈspak trænzmɪtə/ (say spahk tranzmituh) noun a radio transmitting set which generates electromagnetic waves because of the characteristic of a spark gap and a tuned circuit through which energy can surge …   Australian-English dictionary

  • Radio transmitter design — In plate modulation systems the voltage delivered to the stage is changed. As the power output available is a function of the supply voltage, the output power is modulated. This can be done using a transformer to alter the anode (plate) voltage.… …   Wikipedia

  • Nauen Transmitter Station — Large adjustable antenna in Nauen, 2004 Nauen Transmitter Station (German: Grossfunkstelle Nauen or Sender Nauen) in Nauen, Havelland (Kreis), Brandenburg, Germany, is the oldest transmitting plant in the world. It was founded on 1 April 1906 by… …   Wikipedia

  • Invention of radio — Great Radio Controversy redirects here. For the album by the band Tesla, see The Great Radio Controversy. Contents 1 Physics of wireless signalling 2 Theory of electromagnetism …   Wikipedia

  • Timeline of radio — The timeline of radio lists within the history of radio, the technology and events that produced instruments that use radio waves and activities that people undertook. Later, the history is dominated by programming and contents, which is closer… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”