Diode-pumped solid-state laser

Diode-pumped solid-state laser
A frequency-doubled green laser pointer, showing internal construction. Cells and electronics lead to a laser head module (see lower diagram) This contains a powerful 808 nm IR diode laser that pumps a Nd:YVO4 laser crystal, that in turn outputs 1064 nm light. This immediately is doubled inside a non-linear KTP crystal, resulting in green light at the half-wavelength of 532 nm. This beam is expanded and infrared-filtered. In inexpensive lasers the IR filter is inadequate, or is omitted.

Diode-pumped solid-state (DPSS) lasers are solid-state lasers made by pumping a solid gain medium, for example, a ruby or a neodymium-doped YAG crystal, with a laser diode.

DPSS lasers have advantages in compactness and efficiency over other types, and high power DPSS lasers have replaced ion lasers and flashlamp-pumped lasers in many scientific applications, and are now appearing commonly in green and other color laser pointers.



The wavelength of the laser diodes is tuned by means of temperature to produce an optimal compromise between the absorption coefficient in the crystal and energy efficiency (lowest possible pump photon energy). As waste energy is limited by the thermal lens this means higher power densities compared to high-intensity discharge lamps.

High power lasers use a single crystal, but many laser diodes are arranged in strips (multiple diodes next to each other in one substrate) or stacks (stacks of substrates). This diode grid can be imaged onto the crystal by means of a lens. Higher brightness (leading to better beam profile and longer diode lifetimes) is achieved by optically removing the dark areas between the diodes, which are needed for cooling and delivering the current. This is done in two steps:

  1. The "fast axis" is collimated with an aligned grating of cylindrical micro-lenses.
  2. The partially collimated beams are then imaged at reduced size into the crystal. The crystal can be pumped longitudinally from both end faces or transversely from three or more sides.

The beams from multiple diodes can also be combined by coupling each diode into an optical fibre, which is placed precisely over the diode (but behind the micro-lens). At the other end of the fiber bundle, the fibers are fused together to form a uniform, gap-less, round profile on the crystal. This also permits the use of a remote power supply.

Some numbers

High power laser diodes are fabricated as bars with multiple single strip laser diodes next to each other.

Each single strip diode typically has an active volume of:

1 µm 2 mm 100 µm
Height Depth Width
fast axis optical axis slow axis

and depending on the cooling technique for the whole bar (100 to 200) µm distance to the next laser diode.

The end face of the diode along the fast axis can be imaged onto strip of 1 µm height. But the end face along the slow axis can be imaged onto a smaller area then 100 µm. This is due to the small divergence (hence the name: 'slow axis') which is given by the ratio of depth to width. Using the above numbers the fast axis could be imaged onto a 5 µm wide spot.

So to get a beam which is equal divergence in both axis, the end faces of a bar composed of 5 laser diodes, can be imaged by means of 4 (acylindrical) cylinder lenses onto an image plane with 5 spots each with a size of 5 mm x 1 mm. This large size is needed for low divergence beams. Low divergence allows paraxial optics, which is cheaper, and which is used to not only generate a spot, but a long beam waist inside the laser crystal (length = 50 mm), which is to be pumped through its end faces.

Also in the paraxial case it is much easier to use gold or copper mirrors or glass prisms to stack the spots on top of each other, and get a 5 x 5 mm beam profile. A second pair of (spherical) lenses image this square beam profile inside the laser crystal.

In conclusion a volume of 0.001 mm³ active volume in the laser diode is able to saturate 1250 mm³ in a Nd:YVO4 crystal.

Common DPSS processes

Neodymium ions in various types of ionic crystals, and also in glasses, act as a laser gain medium, typically emitting 1,064 nm light from a particular atomic transition in the neodymium ion, after being "pumped" into excitation from an external source. Selection of 946 nm transition light is possible, as well

The most common DPSS laser in use is the 532 nm wavelength green laser pointer. A powerful (>200 mW) 808 nm wavelength infrared GaAlAs laser diode pumps a neodymium-doped yttrium aluminium garnet (Nd:YAG) or a neodymium-doped yttrium orthovanadate (Nd:YVO4) crystal which produces 1064 nm wavelength light from the main spectral transition of neodymium ion. This light is then frequency doubled using a nonlinear optical process in a KTP crystal, producing 532 nm light. Green DPSS lasers are usually around 20% efficient, although some lasers can reach up to 35% efficiency. In other words, a green DPSS laser using a 2.5 W pump diode would be expected to output around 500-900 mW of 532 nm light.

In optimal conditions, Nd:YVO4 has a conversion efficiency of 60%,[1] while KTP has a conversion efficiency of 80%.[2] In other words, a green DPSS laser can theoretically have an overall efficiency of 48%.

In the realm of very high output powers, the KTP crystal becomes susceptible to optical damage. Thus, high-power DPSS lasers generally have a larger beam diameter, as the 1064 nm laser is expanded before it reaches the KTP crystal, reducing the irradiance from the infrared light. In order to maintain a lower beam diameter, a crystal with a higher damage threshold, such as LBO, is used instead.

Blue DPSS lasers use a nearly identical process, except that the 808 nm light is being converted by an Nd:YAG crystal to 946 nm light (selecting this non-principal spectral line of neodymium in the same Nd-doped crystals), which is then frequency-doubled to 473 nm by a beta barium borate (BBO) or lithium triborate (LBO) crystal. Because of the lower gain for the materials, blue lasers are relatively weak, and are only around 3-5% efficient. In the late 2000s, it was discovered that bismuth triborate (BiBO) crystals were more efficient than BBO and LBO and do not have the disadvantage of being hygroscopic,[3] which degrades the crystal if it is exposed to moisture.

Violet DPSS lasers at 404 nm have been produced which directly double the output of a 1,000 mW 808 nm GaAlAs pump diode, for a violet light output of 120 mW (12% efficiency). Initially, these lasers out-performed gallium nitride (GaN) direct 405 nm Blu-ray diode lasers. As direct 405nm diode technology progressed (primarily for use in Blu-ray disc writers) output powers of greater than 500mW have become possible, exceeding the output powers possible from directly doubled 404nm DPSS lasers. Further, the frequency-doubled violet lasers have a considerable infrared component in the beam, resulting from the pump diode.

Yellow DPSS lasers use an even more complicated process: A 808 nm pump diode is used to generate 1,064 nm and 1,342 nm light, which are summed in parallel to become 593.5 nm. Due to their complexity, most yellow DPSS lasers are only around 1% efficient, and usually more expensive per unit of power.

Another method is to generate 1,064 and 1,319 nm light, which are summed to 589 nm.[4] This process is more efficient, with about 3% of the pump diode's power being converted to yellow light.[5]

Comparison to diode lasers

DPSS and diode lasers are two of the most common types of solid-state lasers. However, both types have their advantages and disadvantages.

DPSS lasers generally have a higher beam quality and can reach very high powers while maintaining a relatively good beam quality. Because the crystal pumped by the diode acts as its own laser, the quality of the output beam is independent of that of the input beam. In comparison, diode lasers can only reach a few hundred milliwatts unless they operate in multiple transverse mode. Such multi-mode lasers have a larger beam diameter and a greater divergence, which makes them less desirable. In fact, single-mode operation is essential in some applications, such as optical drives.

On the other hand, diode lasers are cheaper and more energy efficient. As DPSS crystals are not 100% efficient, some power is lost when the frequency is converted. DPSS lasers are also more sensitive to temperature and can only operate optimally within a small range. Otherwise, the laser would suffer from stability issues, such as hopping between modes and large fluctuations in the output power. DPSS lasers also require a more complex construction.

Diode lasers can also be precisely modulated with a greater frequency than DPSS lasers.

See also


External links

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Solid-state laser — A solid state laser is a laser that uses a gain medium that is a solid, rather than a liquid such as in dye lasers or a gas as in gas lasers. Semiconductor based lasers are also in the solid state, but are generally considered as a separate class …   Wikipedia

  • Laser pumping — is the act of energy transfer from an external source into the gain medium of a laser. The energy is absorbed in the medium, producing excited states in its atoms. When the number of particles in one excited state exceeds the number of particles… …   Wikipedia

  • Laser bonding — is a marking technique that uses lasers and other forms of radiant energy to bond an additive marking substance to a wide range of substrates. Invented in 1997, this patent protected technology[1] delivers permanent marks on metals, glass and… …   Wikipedia

  • Laser — For other uses, see Laser (disambiguation). United States Air Force laser experiment …   Wikipedia

  • Laser applications — There are many scientific, military, medical and commercial laser applications which have been developed since the invention of the laser in the 1958. The coherency, high monochromaticity, and ability to reach extremely high powers are all… …   Wikipedia

  • Laser diode — Top: a packaged laser diode shown with a penny for scale. Bottom: the laser diode chip is removed from the above package and placed on the eye of a needle for scale …   Wikipedia

  • Laser pointer — A laser pointer is a portable, pen sized laser designed to be held in the hand, and most commonly used to project a point of light to highlight items of interest during a presentation. Most laser pointers have low enough power that the projected… …   Wikipedia

  • Laser acronyms — Here, is a list of acronyms used in laser physics, applications and technology.A*AOM – acousto optic modulator *APD – avalanche photodiode *APM – additive pulse mode locking *ASE – amplified spontaneous emission *AWG – arrayed waveguide… …   Wikipedia

  • Laser construction — A laser is constructed from three principal parts:*An energy source (usually referred to as the pump or pump source ), *A gain medium or laser medium , and *Two or more mirrors that form an optical resonator . Pump sourceThe pump source is the… …   Wikipedia

  • Disk laser — Not to be confused with Laserdisc. Fig.1. An optically pumped disk laser (active mirror). A disk laser or active mirror (Fig.1.) is a type of solid state laser characterized by a heat sink and laser output that are realized on opposite sides of a …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”