 Defect (geometry)

For other uses, see Defect.
In geometry, the (angular) defect (or deficit or deficiency) means the failure of some angles to add up to the expected amount of 360° or 180°, when such angles in the plane would. The opposite notion is the excess.
Classically the defect arises in two ways:
 the defect of a vertex of a polyhedron;
 the defect of a hyperbolic triangle;
and the excess arises in one way:
 the excess of a spherical triangle.
In the plane, angles about a point add up to 360°, while interior angles in a triangle add up to 180° (equivalently, exterior angles add up to 360°). However, on a convex polyhedron the angles at a vertex on average add up to less than 360°, on a spherical triangle the interior angles always add up to more than 180° (the exterior angles add up to less than 360°), and the angles in a hyperbolic triangle always add up to less than 180° (the exterior angles add up to more than 360°).
In modern terms, the defect at a vertex or over a triangle (with a minus) is precisely the curvature at that point or the total (integrated) over the triangle, as established by the Gauss–Bonnet theorem.
Contents
Defect of a vertex
The defect of a vertex of a polyhedron is the amount by which the sum of the angles of the faces at the vertex falls short of a full circle. If the sum of the angles exceeds a full circle, as occurs in some vertices of most (not all) nonconvex polyhedra, then the defect is negative. If a polyhedron is convex, then the defects of all of its vertices are positive.
The concept of defect extends to higher dimensions as the amount by which the sum of the dihedral angles of the cells at a peak falls short of a full circle.
(According to the Oxford English Dictionary, one of the senses of the word "defect" is "The quantity or amount by which anything falls short; in Math. a part by which a figure or quantity is wanting or deficient.")
Examples
The defect of any of the vertices of a regular dodecahedron (in which three regular pentagons meet at each vertex) is 36°, or π/5 radians, or 1/10 of a circle. Each of the angles is 108°; three of these meet at each vertex, so the defect is 360° − (108° + 108° + 108°) = 36°.
The same procedure can be followed for the other Platonic solids
Shape Number of vertices Polygons meeting at each vertex Defect at each vertex Total defect tetrahedron 4 Three equilateral triangles octahedron 6 Four equilateral triangles cube 8 Three squares icosahedron 12 Five equilateral triangles dodecahedron 20 Three regular pentagons Descartes' theorem
Descartes' theorem on the "total defect" of a polyhedron states that if the polyhedron is homeomorphic to a sphere (i.e. topologically equivalent to a sphere, so that it may be deformed into a sphere by stretching without tearing), the "total defect", i.e. the sum of the defects of all of the vertices, is two full circles (or 720° or 4π radians). The polyhedron need not be convex.^{[1]}
A generalization says the number of circles in the total defect equals the Euler characteristic of the polyhedron. This is a special case of the Gauss–Bonnet theorem which relates the integral of the Gaussian curvature to the Euler characteristic. Here the Gaussian curvature is concentrated at the vertices: on the faces and edges the Gaussian curvature is zero and the Gaussian curvature at a vertex is equal to the defect there.
This can be used to calculate the number V of vertices of a polyhedron by totaling the angles of all the faces, and adding the total defect. This total will have one complete circle for every vertex in the polyhedron. Care has to be taken to use the correct Euler characteristic for the polyhedron.
A potential error
Polyhedra with positive defects It is tempting to think that every nonconvex polyhedron has some vertices whose defect is negative. Here is a counterexample. Consider a cube where one face is replaced by a square pyramid: this elongated square pyramid is convex and the defects at each vertex are each positive. Now consider the same cube where the square pyramid goes into the cube: this is nonconvex, but the defects remain the same and so are all positive.
Negative defect indicates that the vertex resembles a saddle point, whereas positive defect indicates that the vertex resembles a local maximum or minimum.
References
 ^ Descartes, René, "Progymnasmata de solidorum elementis", in Oeuvres de Descartes, vol. X, pp. 265–276
External links
 Weisstein, Eric W., "Angular defect" from MathWorld.
Categories:
Wikimedia Foundation. 2010.