Oxford-Worcester-Wolverhampton Line

Oxford-Worcester-Wolverhampton Line

MetaSidebar|23%|#eeffff|right|Oxford, Worcester and Wolverhampton Railway (1860)|

Oxford
Wolvercote Platform
Yarnton
Hanborough
Combe
Finstock
Charlbury
Ascott-under-Wychwood
Shipton
Kingham
Adlestrop
Moreton-in-the-Marsh
Blockley
Campden
Mickleton
Honeybourne
Littleton and Badsey
Evesham
Fladbury
Wyre
Pershore
Storton
Norton Junction
Worcester Shrub Hill
Droitwich

Hartlebury

Kidderminster

Blakedown

Hagley

Stourbridge Junction

Brettell Lane

Brierley Hill

Round Oak

Harts Hill

Blowers Green

Dudley

Tipton Five Ways

Princes End and Coseley

Daisy Bank

Bilston West

Priestfield

Wolverhampton Low Level

The Oxford, Worcester and Wolverhampton Line was a railway line that was constructed by the Oxford, Worcester and Wolverhampton Railway company between 1845 and 1860.

The track exists today as far as Dudley, with used track existing as far as the location of the old Harts Hill railway station near Dudley. North of Dudley, the trackbed has long since been replaced, and the Wolverhampton terminus at the Low Level station - has, of January 2007, being almost totally demolished (bar its Grade II listed building) to make way for redevelopment.

Development

Other branches included lines to Kingswinford, and Tipton Basin. The Bill stated that the track was to be mixed gauge from Abbotswood near Worcester northwards. It also stated that if the Oxford, Worcester & Wolverhampton failed to complete the line, the Great Western Railway should either lease the line, or purchase the company and complete the line itself. The Bill also stated that the Wolverhampton Low Level station was to be constructed and run jointly with two other companies: the Shrewsbury and Birmingham Railway and the Birmingham, Wolverhampton & Dudley Railway.

The chief engineer was Isambard Kingdom Brunel. His gross underestimation of the cost resulted in the Great Western increasing their shareholding to four percent. Progress was slow and by 1st June 1849 all of the available money was spent, and only the middle section of the line was anywhere near complete, so the Railway Commissioners ordered the Great Western to complete the line. They refused and a legal battle started, but meanwhile the loyalty of the Oxford, Worcester & Wolverhampton towards the Great Western was in decline and it signed an agreement with the London & North Western Railway and the Midland Railway on 21st February 1851 which allowed those companies to finish the line themselves, and then run on it. The Great Western were furious and had the agreement made void, then offered the company a similar deal on their own terms.

The Great Western leased the line, but the ungrateful Oxford, Worcester & Wolverhampton made approaches to the London & North Western to reach Wolverhampton on the Stour Valley line with a junction at Tipton. The GWR protested to Parliament who refused to sanction such a thing and threatened the company with heavy penalties unless the line reached the Low Level station and Cannock Rd Junction by September 1853. The line was eventually finished in July 1853, and opened on 1st December.

Closures and changes

The final section of the railway between Dudley and Bilston was closed to passenger trains in 1962 as one of the first casualties of the Beeching Axe. It remained open to goods trains until December 1967. The track was lifted shortly afterwards and parts of the line have since been built on. The grounds of the Angle Ring factory in Bloomfield Road, Tipton, were the first to swallow up part of the trackbed during the 1980s. The section of line between the Birmingham New Road and Sedgley Road West overbridges on the Coseley-Tipton border was developed as a residential street called Oxford Way in 2002.

The section of the railway between Stourbridge and Dudley was later absorbed into the South Staffordshire Line, which continued to Walsall after forking off eastwards from Dudley. Passenger services had all been withdrawn by 1965, but goods trains continued to serve the route until 1993, when the line north of Round Oak closed. The line is still in use up to this point to serve the local steel terminal, and the closed section is due to re-open in 2011 as part of the Midland Metro's second phase. A single-track line for goods trains will run alongside the Metro between Brierley Hill and Wednesbury and continue on the old trackbed to Walsall.

ee also

* Oxford, Worcester and Wolverhampton Railway
* West Midlands Railway


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Oxford, Worcester and Wolverhampton Railway — [v · d · …   Wikipedia

  • Oxford Road Halt railway station — This article is about a former railway station in Oxfordshire. For the existing station in Manchester, see Manchester Oxford Road railway station. Oxford Road Halt Location Place Water Eaton Area Cherwell Grid reference …   Wikipedia

  • Cotswold Line — Overview Type Rural, Heavy rail System National Rail …   Wikipedia

  • Wolverhampton —   City   City of Wolverhampton …   Wikipedia

  • Cross-City Line — Butlers Lane station Overview Type Heavy rail, Suburban rail …   Wikipedia

  • Wolverhampton — Wolverhampton …   Wikipédia en Français

  • Wombourne Branch Line — The Wombourne Branch Line was a railway situated in Central England. The line branched from the Oxford Worcester Wolverhampton Line at Kingswinford Junction to the north of Brettell Lane railway station and joined track at the triangular Oxley… …   Wikipedia

  • Oxford — This article is about the city of Oxford in England. For other cities and other meanings, see Oxford (disambiguation). Oxford   City   …   Wikipedia

  • Oxford, Witney and Fairford Railway — [v · d · …   Wikipedia

  • Worcester Shrub Hill railway station — Infobox UK station name = Worcester Shrub Hill catpion = View from Platform 2b on 5 September 2006 code = WOS manager = London Midland locale = Worcester borough = Worcester usage0405 = 1.356 usage0506 = 0.203 usage0607 = 0.592 platforms = 3… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”