Sprag clutch

Sprag clutch
One-way bearing combining sprags and bearing rollers in one race

A sprag clutch is a one-way freewheel clutch. It resembles a roller bearing, but instead of cylindrical rollers, non-revolving asymmetric figure-of-eight shaped sprags are used. When the unit rotates in one direction the rollers slip or free-wheel, but when a torque is applied in the opposite direction, the rollers tilt slightly, producing a wedging action and binding because of friction. The sprags are spring-loaded so that they lock with very little backlash.



Automatic transmissions

A sprag clutch is used in some automatic transmissions as a method of allowing the transmission to smoothly change gears under load. Various models of General Motors' turbo-hydramatic gearbox have used this system.

A sprag clutch is used in most older automatic transmissions and some newer ones for shifts which require the synchronized engagement of one clutch with the disengagement of another. Using an overrunning clutch instead of a hydraulically actuated one makes this synchronization automatic. The sprag clutch simply "lets go" once the reaction force it provides is no longer needed. In a Simpson gearset, common to many automatics, this happens on the 1-2 shift, and reverses on the 2-1 downshift. The 2-3 shift is done by engaging a single clutch, and nothing is released. Some newer electronically controlled transmissions make "clutch to clutch" shifts, without any sprags.

This can also be used exclusively in first gear (transmission shift lever in D, but auto valve body or management selecting 1st) on some autos. That way it will automatically provide forward drive, but will not provide any engine braking. This is done not so much to avoid engine braking per se, but rather to allow a low throttle opening 2-1 downshift as a car decelerates, to avoid a loud (and potentially abrupt) and unnerving jolt as a result of the downshift. On transmissions so equipped, manual selection of 1st gear typically engages an additional band that grips the same section as the one way clutch would engage, and thus allows for engine braking.


A sprag clutch is used in many helicopter designs to transfer power from the engine to the main rotor. In the event of an engine failure, the sprag clutch allows the main rotor to continue rotating faster than the engines so that the helicopter can enter autorotation.[1]

Motorcycle applications


A sprag clutch is used in the electric starter motors of modern motorcycle engines to replace the Bendix gear common to automobile starters.

Primary drive

Many modern sport and racing bikes use sprag clutches in the primary drive between the engine and transmission. This prevents the rear wheel from losing traction during rapid downshifts when the engine speed is not matched to road speed. If a sprag clutch is not present, much greater care is required when downshifting because losing rear wheel traction can cause dangerous highside accidents.


On conveyor drives, a sprag clutch is used for indexing and anti-runback.


Overrunning occurs when two or more motors can be used to drive the same machine, including through the same shaft. A typical setup is as follows. The service drive, or prime mover, provides a combination of high speed and high power for normal operation. The secondary drive, or pony drive, can be run at low speed and low power, usually to position the conveyor for maintenance.

The overrunning clutch allows the secondary drive to remain stationary during normal high speed operation of the conveyor drive.


An indexing motion provides for accuracy in the drive system. A link is installed between the prime mover and one race of the sprag clutch. The reciprocating motion of the prime mover is converted to an indexing movement on the other race of the sprag clutch.


Backstopping prevents a loaded inclined conveyor from running back when the drive system is stopped. The outer race of the sprag clutch is fixed to the machine frame, usually via a torque arm. The inner race rotates freely in the forward direction of the conveyor drive. When the machine tries to run backward, the sprag clutch prevents this motion. In this application the sprag clutch is often called a "backstop" or "holdback".

Hoist load brake

A hoist load brake is used as a secondary brake to prevent industrial hoists from catastrophically dropping their loads in the event of mechanical failure.


Sprag clutches may be oil or grease lubricated. Most sprag clutch manufacturers do not allow the use of lubricants containing extreme pressure additives.

See also


  1. ^ Federal Aviation Administration, Flight Standards Service (2007). Rotorcraft Flying Handbook (Illustrated ed.). Skyhorse Publishing. p. 5–4. ISBN 1602390606. 

External links

Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • sprag clutch — A mechanical clutch used in reciprocating engines and direct shaft turbine engines. It helps remove the load of the rotor when the engine is being started. In helicopters, it allows the engine to drive the rotor, but when the engine power is… …   Aviation dictionary

  • sprag clutch — A clutch that will allow rotation in one direction but that will lock up and prevent any movement in the other direction …   Dictionary of automotive terms

  • Sprag — A sprag is a one way freewheel clutch used in a number of applications. It resembles a roller bearing with rollers shaped like a figure eight and cocked with a spring. When the unit rotates in one direction, the rollers stand up and bind because… …   Wikipedia

  • clutch — [1] An electrically operated coupling device that connects or disconnects the compressor pulley and compressor shaft [2] A device that disconnects the engine from the transmission, to allow the vehicle to change gears, and then allows the engine… …   Dictionary of automotive terms

  • one way clutch — A mechanical clutch which transmits power in one direction of rotation only; when torque is not applied, the driven member rotates freely; used in automatic transmissions and the old freewbeel. See freewheeling sprag clutch reactor one way clutch …   Dictionary of automotive terms

  • Slipper clutch — A slipper clutch (also known as a back torque limiter) is a specialized clutch developed for performance oriented motorcycles to mitigate the effects of engine braking when riders decelerate as they enter corners. They are designed to partially… …   Wikipedia

  • Automatic transmission — An automatic transmission (commonly AT or Auto ) is an automobile gearbox that can change gear ratios automatically as the vehicle moves, freeing the driver from having to shift gears manually. Similar but larger devices are also used for heavy… …   Wikipedia

  • Freewheel — For information about the bicycle component, see Cogset. Freewheel mechanism …   Wikipedia

  • Automobile self starter — An automobile self starter (commonly starter motor or simply starter ) is an electric motor that initiates rotational motion in a car s internal combustion engine before it can power itself. History Both Otto cycle and Diesel cycle internal… …   Wikipedia

  • Jane Dornacker — (October 1, 1947 October 22, 1986) was an American rock musician, actress, and comedienne turned traffic reporter.In 1986, while working for WNBC 660 AM Radio in New York City (which became WFAN in 1988), she was aboard during two unrelated… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”