Colt Police Positive

Colt Police Positive
Blued Colt Police Positive revolver; six inch barrel
Type	Revolver
Place of origin	United States
Production history
Manufacturer	Colt's Manufacturing Company
Produced	1907-1947
Variants	See Variants
Specifications
Barrel length	2.5 in (63.5 mm) 4 in (102 mm) 5 in (125 mm) 6 in (153 mm)
Cartridge	.32 Long/Short Colt .32 Colt New Police (.32 S&W Long) .38 Colt New Police (.38 S&W)
Action	double-action
Feed system	six round cylinder
Sights	Fixed iron; half-moon blade front, V-notch rear

The Colt Police Positive is a small frame double-action revolver featuring a six-round cylinder, chambered for either .32 or .38 caliber cartridges. Designed primarily for sale to federal, state, or local law enforcement agencies, the Police Positive was introduced into the firearms market by the Colt's Manufacturing Company in 1907.^[1][2][3]

Development and history

The Colt Police Positive was an improvement of Colt’s earlier “New Police” revolver, upgraded with an internal hammer block safety. Colt named this new security device the “Positive Lock”, and its nomenclature ended up being incorporated as a partial namesake for the new revolver.^[2] The cylinder of the Police Positive rotated in the clockwise direction, the opposite of firearms maker Smith & Wesson's competing models. Ever a canny competitor in the firearms milieu, Colt missed no opportunity to score a Coup d'état over its arch rival, and began a marketing campaign which accentuated this detail. In its advertising Colt proclaimed that "All Colt cylinders TURN TO THE RIGHT", and suggested that the Colt design forced the cylinder crane up against the frame, resulting in tighter lockup with less play and better chamber to barrel alignment, thus markedly increasing accuracy.^[2] The Police Positive was very successful; along with the Colt Official Police it dominated the law enforcement firearms market in the early 1900’s.^[4] The Positive was itself incrementally modified in 1908, forming the basis for Colt’s Police Positive Special model.^[2]

A nickel Police Positive with pearl grips was used by Charles Bronson as Paul Kersey in Death Wish. And also the notorious american gangster Al Capone used a Police Positive, a nickel .38 Police Positive with walnut grips and a 4 inch barrel, manufactured in 1938, to be precise. In June 2011 a private collector sold it at Christie's for a sum of £67,250/$109,080/€75,656. ^[5]

Features

The Police Positive was made of carbon steel, and was finished with either a polished blued finish or nickel plated.^[2] The First issue of the Police Positive ran from the revolver’s introduction in 1907 until 1927. Sporting Colt’s standard hard rubber grips, it was offered with barrel lengths of 2.5 (available only in .32 caliber), 4, 5, and 6 inches, and was chambered for the .32 Long Colt (which would also fit the .32 Short Colt), .32 Colt New Police, and .38 Colt New Police cartridges.^[1][2][3][6] Checkered Walnut grips became standard after 1923. The Second issue began in 1928 and ran until 1947, adding a somewhat heavier frame as well as a serrated topstrap to reduce sight glare, while retaining the wooden grips.^[6] Both of Colt's “New Police” rounds were actually slight redesigns of existing S&W cartridges, the .32 S&W Long and .38 S&W with the bullet noses flattened, as Colt resisted providing its main competitor with any free advertising.^[2] Colt's Positive Lock safety, the innovation responsible for the gun's introduction, functioned by preventing the firing pin from striking the primer of the cartridge unless the trigger was deliberately pulled. Intended to address deficiencies of earlier models such as the Single Action Army, the Positive Lock prevented an accidental discharge even if the hammer was struck or the pistol was dropped, allowing the revolver to be safely carried with all six chambers loaded.^[7] The revolver’s sights consisted of a half-moon blade front with a fixed iron open rear sight, which was a simple V-notch shaped groove milled into the revolver’s topstrap.^[2]

Variants

Police Positive Target

Weighing 22 ounces and available with a blued finish and black hard rubber grips in .22 Long Rifle, .22 WRF, .32 Long (and Short) Colt, and .32 Colt New Police (.32 S&W Long) chamberings, the First issue of this model featured an adjustable open iron sighted 6 inch barrel and was marketed from 1910 to 1925, with checked Walnut grips replacing the rubber ones after 1923. A Second issue was sold from 1926 to 1941 and differed from the First in that it had a slightly heftier frame which upped the weight to 26 ounces; also Colt’s nickel finish was offered as an option.^[6] In today's collectable market, the .32 New Police version appears to be the most sought after and valuable.^[2]

References

1. ^ ^{a b} “Colt Police Positive” Bellum Web site. Accessed September 16, 2008.
2. ^ ^{a b c d e f g h i} Shideler, Dan. “Nobody Wants This Colt”, Gun Digest magazine Web site. Accessed September 16, 2008.
3. ^ ^{a b} Lark, Syd. “Colt .38 Police Positive”, All Experts Web site. Accessed September 16, 2008.
4. ^ Scarlata, Paul. “Colt's Official Police Revolver”, Shooting Times magazine Web site – Handgun Reviews. Accessed August 13, 2008.
5. ^ http://www.christies.com/about/press-center/releases/pressrelease.aspx?pressreleaseid=4895
6. ^ ^{a b c} "COLT'S MANUFACTURING COMPANY, INC. REVOLVERS: DOUBLE ACTION, SWING OUT CYLINDER", Cheaper Than Dirt Web site. Accessed September 22, 2008.
7. ^ Cumpston, Mike. “.32 Colt Police Positive Special”, Gunblast Webzine. Accessed September 11, 2008.

External links

• The Colt Revolver in the American West—Police Positive .22 Target Model G
• The Colt Revolver in the American West—Cutaway Police Positive .38 Model