Aircraft warning lights

Aircraft warning lights are high-intensity lighting devices that are attached to tall structures and used as collision avoidance measures. Such devices make the structure much more visible to passing aircraft and are usually used at night, although in some countries they are used in the daytime also. These lights need to be of sufficient brightness in order to be visible for miles around the structure.

Lamp types

The lights generally come in two forms:

* Red lamps that are either constantly illuminated or turn on and off slowly in a cycle of a few seconds
* White xenon discharge flashers

Both types were in use in the United Kingdom until recently, however new regulations stipulate the use of red lamps at nighttime only. Xenon flashers are therefore gradually being phased out.

In the United States and Canada, there are several types of lights:
*Obstruction lights (that are constantly illuminated)
*Red Beacons/Red strobes
*High Intensity White (Strobe) Lights
*Medium Intensity White (Strobe) Lights

Traditionally, red lamps (or beacons) use incandescent filament bulbs. In order to improve the otherwise quite short lifespan, they are made with a ruggedised design and are run below normal operating power (under-running). A recent development has been the use of arrays of high power red LEDs in place of incandescent bulbs, which has only been possible since the development of LEDs of sufficient brightness. LED based lamps have a significantly longer lifespan than incandescent bulbs, thus reducing maintenance costs and increasing reliability.

Xenon flashers, whilst more visually impressive, tend to require frequent replacement and so have become a less favoured option. However, with the advent of LEDs, white strobes are still somewhat desired.

It is common to find structures with white xenon flashers/white strobes during the daytime, and red lights at night. Red lights are commonly found to be used in urban areas, since it is easier for pilots to spot them from above. White strobes (that flash 24/7) may also be used in urban areas. However, it has been recommended that flashing white strobes should not be used in densely populated areas; the lights usually merge with background lighting at nighttime, making it difficult for pilots to spot them and thereby aggravating the hazard. In addition, some residents (residing near the lit structure) will complain of "light pollution."

In rural areas, red beacons/strobes may also be used during nighttime. However, white strobes are (sometimes) preferred since it reduces maintenance cost (i.e. no maintenance of painting, no red side lights) and there are no background lights that would blend with the strobes.

For white strobes, there is a medium intensity white strobe and a high intensity white strobe. Medium Intensity White Strobes are usually used on structures that are between 200-500 feet (61-152.4 meters). If a medium white strobe is used on a structure greater than 500 feet (152.4 meters), the structure "must" be painted.

The common medium white strobe flashes 40 times in a minute, at an intensity of 20,000 candelas for daytime/twilight, and 2,000 candelas at nighttime.

A high intensity white strobe light is used on structures that are greater than 500 feet (152.4 meters). Unlike a medium strobe, a high intensity strobe doesn't provide 360˚ coverage, which requires the use of at least 3 high strobes at each level. On the other hand, it reduces maintenance costs (i.e. no painting). If the structure has an antenna at the top that is greater than 40 feet, a medium intensity white strobe light must be placed above it rather than below.

The common high white strobe flashes 40 times in a minute, at an intensity of 270,000 candelas for daytime, 20,000 candelas at twilight, and 2,000 candelas at nighttime.

"Dual" lighting is where a structure is equipped with white strobes for daytime use, and red beacons/strobes for nighttime use. In urban areas, these are commonly preferred since it usually exempts a structure from the requirement of having to be painted. One advantage to the dual system is that when the uppermost red lights fail, the lighting switches onto its "Backup" lighting system, which uses the white strobes (at its night intensity) for nighttime. In the United States and Canada, red beacons are slowly going out of commission and being replaced with red strobes. In addition, some medium strobes are equipped to flash the white light for daytime and red light for night in a single strobe (unlike the old type which had two different lights).

For high tension power lines, the white strobes are equipped to flash 60 times per minute, using the same intensities as stated above. Unlike the common white strobes, these strobes are specified not to flash simultaneously. The flash pattern should be middle, top, and bottom to provide "a unique system display". [http://www.faa.gov/ats/ata/ai/AC70_7460_1K.pdf Advisory Circular 70-7460-1K] from Federal Aviation Administration]

On aircraft

Along with warning lights on ground based structures, aircraft also consist of a warning light system used to warn other aircraft of their presence. These lights include landing lights, strobe lights, and wingtip lights. The wingtip lights are required by the FAA to consist of a red light on the left wingtip and a green light on the right wingtip. Landing lights are used below 10,000ft MSL or when required under certain conditions.

Use and positioning

These lights can generally be found attached to any tall structure such as broadcast masts and towers, water tanks located on high elevation, electricity pylons, chimneys, tall buildings, cranes and wind turbines. Shorter structures that are located close to airports may also require lighting.

Lights are usually arranged in clusters around the structure at specific heights above the ground. Frequently there will be a set at the top, and then one or more sets equally spaced down the structure. England's Belmont mast (the tallest construction in the European Union) has nine clusters of red lamps spaced equally along the full height of the mast.

ee also

* Light pollution

References

External links

* [http://tx.mb21.co.uk/gallery/membury/index.php The Transmission Gallery: Close up of LED warning lamp array on the Membury mast]
* [http://tx.mb21.co.uk/gallery/belmont/index.php The Transmission Gallery: Belmont mast - includes night shot showing the nine sets of warning lamps]