caption=The breech end of two Kammerlader rifles
service=1842 – 1870
Minié ballin paper cartridge
rate= Depended on how quickly the shooter could reload.
velocity= Sources vary; between 265 m/s to 350 m/s
range= Accurate to 1,100 m, see text.
weight= "M1849/55": 5 kg (11 lb), other models likely differed from this
length= "M1849/55": 126 cm (50.4 in), other models likely differed from this
part_length= "M1849/55": 78 cm (30.7 in), other models likely differed from this
sights=V-notch and front post
M1862 Artillery carbine
M1862/66 Artillery carbine
"Royal Norwegian Navy:"
"Various civilian models"
number=More than 40.000|
The Kammerlader, or "chamber loader", was the first Norwegian breech loading
rifle, and among the very first breech loaders adopted for use by an armed force anywhere in the world. A single shot black powderrifle, the "kammerlader" was operated with a crank mounted on the side of the receiver. This made it much quicker and easier to load than the weapons previously used. "Kammerladers" quickly gained a reputation for being fast and accurate rifles, and would have been a deadly weaponagainst massed ranks of infantry.
The "kammerlader" was introduced in 1842, and it is thought that about 40,000 were manufactured until about 1870. While first flintlock breech loading rifles, such as Ferguson, were launched decades before 1842 Norway was the first European country to introduce breech loaders on a large scale throughout its army and navy. Though United States was the first in the world with
M1819 Hall rifle. The "kammerladers" were manufactured in several different models, and most models were at some point modified in some way or other.
The "kammerladers" were phased out as more modern rifles were approved for use. They were either modified for
rimfirecartridges, sold off to civilians or melted for scrap. Rifles sold to civilians were often modified for use as shotguns or huntingfirearms. Today it is hard to find an unmodified "kammerlader", and collectors often pay high prices for them.
In the early 1800s, the
Norwegian Armydecided that the nature of warfare was changing away from the massed ranks firing in volleys towards smaller units advancing and firing independently. This conclusion was reached after having observed the American Revolutionary War, the Napoleonic Warsand the short Swedish campaign against Norway in 1814. Lessons were also learned from the Gunboat War, where small, mobile gunboats outmaneuvered larger, more heavily armed ships. It was decided that a breech loaded rifle was needed, more accurate than the old smoothbore muskets, yet quicker to load than the rifles issued to the Norwegian Jeger and Skijeger units. A special committee was created, and it started considering various firearm actions in 1837. It was soon clear that the desired weapon should:
*have a reduced caliber compared to the then standard musket;
*have reliable ignition, with the means of the
caplock mechanism(earlier muskets had been equipped with the flintlock mechanism);
*be quicker to load than the musket, and therefore be a breech loader; and
*be more accurate than the old smoothbore muskets.The end result was that a modern, breech loading rifle was approved for use on the 18 May 1842. The caliber chosen for the new rifle was 18 "lødig" (gauge); in other words, one could manufacture 18 round bullets out of one Norwegian pound of lead. In modern terms this means the caliber of the rifle was 17.5 mm.
From 1842 until the
Remington M1867was approved in 1867, more than 40,000 kammerladers in more than 80 different models were manufactured. In 1860 the caliber was reduced again, to four Swedish Linjerref|Foot_1, or about 11.77 mm. When some of the "Kammerladers" were modified to rimfire after 1867, this meant that the barrels had to be bored out to 12.17 mm to accept the new cartridge.
During a military sharpshooting competition held in
Belgiumin 1861, the "Kammerlader" was proven to be among the most accurate military long arms in Europe. The Norwegian rifles were shown to be accurate to a range of about convert|1|km|abbr=on|1, which is quite an achievement even by today's standards.
Every breechloader must have some form of mechanism that allows the
breechto be opened for loading, yet securely locked for firing. This was even more important in the early designs made before the introduction of the cartridge. Achieving a gas-tight seal was difficult with the metallurgyof the day, and it can be argued that the Norwegian "kammerladers" are the first fully successful military breechloaders—the needle gunwas slightly earlier, but it leaks a significant gas pressure around the breech. A crank mounted on the side of the weapon operates the "kammerlader". Rotating the crank opens the breech of the weapon, allowing for loading. The use of paper cartridges—a pre-measured amount of gunpowder and a lead bullet wrapped in paper—also sped up the rate of fire. While not as fast as more modern rifles, which use fixed cartridges, the "kammerlader" was much faster than contemporary muzzleloading rifles. The loading sequence is as follows (refer to picture):
# The hammer mounted under the weapon is cocked.
# The crank is rotated, opening the breech.
percussion capis placed on the nipple.
# A pre measured amount of
gunpowderis poured into the breech, and the paper from the paper cartridge is used as wadding.
bulletis placed in the chamber.
# The crank is rotated forwards, locking the breech and making the rifle ready to fire.The exact rate of firing with the "kammerlader" depends, as with all manually operated weapons, entirely on the shooter. While the sources do not give any indication as to the rate of fire attainable by the average soldier, it is known that it was higher than for a muzzle loading
musket—roughly four rounds a minute—and most probably lower than the contemporary German needle gun's 10 to 12 rounds a minute, since the "kammerlader" has a more elaborate loading procedure.
Most of the rifles were modified during their
service life. The first major modification was the change from a fixed rear sight mounted behind the receiver to an adjustable rear sight mounted in front of it. The first of the adjustable rear sights was a 'flip over' type: an L-shaped piece of metal that was hinged so it could 'flip' over. Later this was again modified to a design known in Norway as a 'ski hill sight'; a simple, yet functional, adjustable tangent sight. In principle, this latest sight doesn't differ from the iron sightsfound on most modern firearms. Towards the end of the service life of the "kammerladers", most of the small bore rifles were modified to allow the use of rim fire ammunition.
The "kammerlader" was designed to use paper cartridges—a pre-measured amount of gunpowder and a lead bullet wrapped in paper—both to speed up and simplify loading the weapon. In the early days of the rifle most units used round bullets in their weapons, but in 1855 it was decided that all units should use the
Minie ballinstead since this gave better accuracy. The paper was wrapped around the cylindrical section of the bullet and secured with wool string secured in the grooves. The end of the bullet was then covered in melted tallow, before the black powderwas filled in behind the bullet and the end wrapped. For the 18 lødig rifles, a load of 96 grains (6.22 g) was used. Sources vary in the reported muzzle velocity, but it is known that during tests in 1849, the bullet penetrated two inches (50 mm) of wood at a distance of 800 alen (500 m).
Modification to rimfire
After the introduction of the
Remington M1867and its rimfirecartridge in 1867, the Norwegian Army and the Royal Norwegian Navy decided to convert some of the stock of "kammerladers" into rim fire rifles. There were two designs used for the modification: Landmarks and Lunds. Neither can be considered completely successful, but both were cheaper, and quicker, than manufacturing new M1867s. It seems that the Norwegian Armypreferred the Lund, while the Landmark was the option of choice for the Royal Norwegian Navy.
For the "Lund conversion", the chamber was replaced with a
breechblock, and an extractor was mounted on the left side of the receiver. A chamber fitting the 12.17 x 44 mmrimfire cartridge was milled out of the rear part of the barrel. The right side of the receiver was lowered 6 mm and the bottom plate exchanged from a brass plate to a steel plate with a track for the extractor. The firing pinwas curved to allow the hammer to strike it.
The mechanism of the "Landmark conversion" is brilliantly simple. The chamber is opened as before, but can be tilted further backwards by means of a hinge in the middle of the chamber. The 12.17 x 44 mm rimfire cartridge is placed backwards, facing the shooter, before everything is rolled back forward. The only part to be modified was the chamber and a curving firing pin was added where the nipple for the cap had been.
A number of the "kammerladers" were also converted with the Remington action, by replacing the receivers but keeping the barrels and woodwork. These can be distinguished from ordinary Remington M1867s by having a shorter receiver with more rounded corners. It is unknown how many "kammerladers" were modified in this fashion.
The "kammerlader" rifles were manufactured over a period of 25 years (1842 to 1867) in a wide range of both military and civilian models. Almost all the military rifles were modified once or more, resulting in a very wide range of different models for a collector to collect.
* "M1842 Army" kammerlader. The first model manufactured, differed from later models with a narrower hammer. Production numbers are unknown, but very limited. It can be considered an experimental model.
* "M1845 Navy" kammerlader. Very rare in original state. Only 100 were manufactured in 1845. Outwardly very similar to M1842. The barrel is mounted to the stock with three brass bands.
* "M1846/55 Army" kammerlader. At first glance very similar to the M1842, but a closer inspection reveals substantial differences. Most pronounced is the different style of hammer. Unlike the M1842, which had a narrow, ridge like hammer, the M1846 is wider and had a bigger handle. Most M1846 saw a lot of service and show wear. In 1855, the rear sight was modified and moved, changing the designation to M1842/55. It is hard to find an unmodified rifle today. Some 6000 rifles were manufactured; 3000 at Kongsberg Våpenfabrik, while
Crausein Hertzbergand Francottein Liege produced an additional 1500 each.
* "M1849 Navy" kammerlader. Mostly similar to the M1845. 500 were manufactured in 1849. Most were later converted to rim fire.
* "M1849/55 Army" kammerlader. Probably the second most common large bore kammerlader, with a total production of more than 10,000 rifles (2,000 produced by A. Francotte in Liege, Crause in Hertzberg produced another 2,000 and Kongsberg Våpenfabrikk 6,021). In addition, a further 4.500 were manufactured at Kongsberg Våpenfabrikk in 1855 directly as M1849/55. There were a couple of improvements on the M1849, compared to the earlier model. The hammer was widened for a better grip, the butt plate was bent up under the stock in order to protect this better. As far as is known, all the M1849 had fitted new rear sights in 1855, attached with a band around the barrel—or at least no unmodified M1849 are known today. Since this is such a common variation, it is also one of the more affordable for a collector.
* Swedish "M1851 kammarladdningsgevär för flottan" (chamber loader for the Navy). Two brass bands securing the barrel to the stock, a ring on the hammer for cocking and a caliber of 14.8 mm. Otherwise it looks quite similar to Norwegian "kammerladers". While much more modern than the Swedish rifles in service at the time, the M1851 was considered a failure and probably was not issued for service.
* "M1852/67 Navy" kammerlader. One of the more common naval kammerladers, this was a short, small bore (18 Lødig, about 18 bore) rifle in which the barrel was attached to the stock with three brass bands. It also had a 'ski hill' rear sight. This was the last of the naval kammerladers with three bands. Virtually all were converted to rim fire in 1867 by means of the Landmark conversion. It is believed that about 500 were manufactured.
* "M1855/67 Navy" kammerlader. This must be considered a product improved M1852. Major differences were the number of bands (the M1855 used just two), a different rear sight and the shape of the stock. After the introduction of the rim fire Remington M1867, they were modified with the Landmark conversion, the sights being altered to a rocking pattern graduated up to 800 alen (500 m).
* "M1857/67 Navy" kammerlader. Identical to the M1855, except the shape of the butt plate. It is assumed that a total of 300 or so were manufactured, all of which were probably modified to rim fire in 1867.
* "M1859 Army" kammerlader. A short rifle with two bands, it was produced for the Sharpshooter Company in Stockholm (today known as the Kings Guard), for the Jegers and for sergeants in the infantry. The majority of the M1859 was converted from M1849, M1855 and possibly also from the M1846 rifles. Only the numbers between 10858 and 12183 were originally manufactured as M1859’s. Today, it remains the most common large bore kammerlader available to a collector.
* "M1860/67 Navy" kammerlader. The first of the naval small bore kammerladers, and the only naval kammerlader with just two bands. Virtually all were converted to rim fire with the Landmark conversion.
* "M1860/67 Long Army". Originally a 4 Linjers (11.77 mm) caliber derivative of the M1855, this
long riflehad hexagonal Whitworth-style rifling. It was fitted either with a simple two-leaf rocking sight (on rifles issued to the rank and file) or with a tangent-leaf on rifles issued to snipers. In total about 8,500 were manufactured between 1860 and 1867, the majority later converted to rim fire with the Lunds conversion. In addition, about 1,600 were manufactured with the conversion from new between 1868 and 1870.
* "M1860/67 Short Army". The same weapon as the Long Lund, except in carbine form. About 3,200 were manufactured between 1862 and 1866. Identical in most respects to the Naval M1860, except that it was modified to rim fire with the Lunds conversion.
* "M1862/66 Artillery carbine". This diminutive weapon had a barrel less than half as long as the M1860. Everything except the bore seems to be scaled down from a M1859 or similar, and the gun might be hard to identify as an M1862 from pictures alone. Production numbers unknown; all are thought to have been modified with the Lund conversion to rim fire in 1869.
Fate of the "kammerladers"
The "kammerladers" were phased out as more
modern weaponsbecame available—the Remington M1867, the Krag-Petersson(adopted by the Royal Norwegian Navy in 1876), and the Jarmann M1884. It is likely that the last of the modified naval "kammerladers" was not finally removed from military warehouses until after the Krag-Jørgensenwas approved for use in 1892, although sources are scarce on this. The rifles were either sold to civilians or melted down for scrap.
Most of the rifles sold to civilians were turned into hunting implements, by replacing the barrel and/or the woodwork. Some of these were supposedly used for illegal hunting during
World War II, when the occupying Germans had seized all modern weapons owned by civilians. Today it is hard to find a "kammerlader" in original condition, or indeed at all.
Present day collectors are often willing to pay significant amounts for a "kammerlader" in good condition—various sources state the price to be around 10,000 Norwegian Kroner (US$1,600) and upwards of 50,000 Norwegian Kroner ($8,000) depending on the model and condition of the gun for sale.
Comparison with contemporary rifles
The "kammerlader" is often claimed to be an outstanding weapon for its time. The only contemporary rifle which it can be compared to is the Prussian
needle gun- the only other breech loader adopted for service in the 1840s.
* The United States'
Springfield model 1842 smoothboremusket, and Springfield model 1855and Springfield Model 1861 rifled muskets.
* The German
needle gun, adopted in 1848.
Earlier breechloading rifles
M1819 Hall rifle
Websites about the "Kammerlader":
* [http://www.geocities.com/trondwikborg/kammerladere.html A gun collector's page on the "kammerlader"]
* [http://www.svartkrutt.net/engkammer.php English article on the "kammerlader"]
* [http://www.svartkrutt.net/ladekamr.php A series of drawings showing how to load a unmodified "kammerlader"]
* [http://www.militaryrifles.com/Norway/Lund.htm An article on the Lund modification, with excellent pictures]
* [http://www.cascity.com/cgi-bin/1873/print.pl?article=105 Short article on shooting the M1846]
Images of various models and modifications of the "kammerlader":
"Various models of the kammerlader:"
* [http://geocities.com/trondwikborg/M1845.html Photographs of the M1845]
* [http://geocities.com/trondwikborg/M1846.html Photographs of the M1846]
* [http://geocities.com/trondwikborg/M1849.html Photographs of a M1849 manufacured in Liege]
* [http://geocities.com/trondwikborg/Hertzberg.html Photographs of a M1849 manufactured by Crause]
* [http://wagner-eltze.de/antike_langwaffen/perk_kammerlader.htm Several photos, including closeups, of a M1849/55]
* [http://geocities.com/trondwikborg/M1852.html Photographs of a M1852 (converted to rim fire)] .
* [http://geocities.com/trondwikborg/M1855navy.html A photograph of a modified M1855] .
* [http://geocities.com/trondwikborg/M1859.html Photographs of the M1859]
* [http://geocities.com/trondwikborg/M1860Landmark.html Photographs of the M1860/67 ] , including a set that shows how the breech opens.
* [http://geocities.com/trondwikborg/M1860.html Photographs of the long and short M1860/67]
* [http://geocities.com/trondwikborg/M1862.html Photographs of the M1862 carbine]
* [http://www.forum.svartkrutt.net/img/uploaded/image170.jpgPhoto of a Swedish M1851 manufactured at "Carl Gustav" weaponfactory]
* [http://www.forum.svartkrutt.net/img/uploaded/image171.jpgPhoto of a Swedish M1851 manufactured by "P.J.Marlherbe a Liége"]
* [http://www.svartkrutt.net/kammerpatrkule.jpgA photo of a paper cartridge (modern reproduction)]
"Modifications to rimfire:"
* [http://www.svartkrutt.net/landmark.php A selection of photos of a "kammerlader" modified with the Landmark conversion]
* [http://www.militaryrifles.com/Norway/MoreLund.html Photos of a "kammerlader" modified with the Landmark conversion] - site wrongly identifies this as a Lund
* [http://www.geocities.com/trondwikborg/lundspatent.jpgA composite photo showing the Lund conversion] .
* [http://www.geocities.com/trondwikborg/M1860forskjellige1.jpgComparison of modified and unmodified "kammerladers" with closed breeches] From the top: Landmark, Lund, original breech
* [http://www.geocities.com/trondwikborg/M1860forskjellige2.jpgComparison of modified and unmodified "kammerladers" with open breeches] From the top: Landmark, Lund, original breech
"The kammerlader in use"
* [http://home.no.net/reinset/fra.htm Several photos of the "kammerlader" in use today] , targetshooting under the heading "Fra kammerladerfelten i Mulvika 31.08.2002" (3 photos), and reenactors using the "kammerlader" under the heading "Svartkruttstemne 04.05.2002" (halfway down the page, 4 photos).
* The reason Norway choose to use a Swedish measurement for the caliber can be found in the fact that Norway and Sweden were in a union at the time, and the military of both nations had an agreement that they would choose weapons with interchangeable ammunition. Later this resulted in both nations adopting the 12.17 × 44 rim fire cartridge in 1867 and the 6.5 × 55 cartridge in 1894.
* The sources are unclear, but varies between these two extremes. Possible because there are so many models of the "kammerlader" out there.
* [http://geocities.com/norskevaapen/ A gun collectors pages on various Norwegian weapons] —relevant pages retrieved on 8 July 2005
* [http://www.svartkrutt.net/engkammer.php An article on the "kammerlader" in English] . Retrieved 12 July 2005
* [http://www.jeger.no/text.cfm/4923+1+493+96 An article in the Norwegian magazine "Jeger, hund våpen"] , retrieved 15 September 2005
Wikimedia Foundation. 2010.