Portable engine

A portable engine is a small steam engine, mounted on wheels or skids, which is used for driving machinery using a belt from its flywheel. It is not self-propelled and is towed to the work site by horses or bullocks, or even a traction engine. Portable engines were used mainly for driving agricultural machinery, such as threshing machines. In industrialised countries they are no longer used for commercial purposes, but preserved examples can often be seen at steam fairs driving circular saws or other equipment for demonstration purposes.

History

In common with many other areas of steam technology, the initial design and development of portable engines took place in England, with many other countries initially importing British-built equipment rather than developing their own.

Early steam engines were too large and expensive for use on the average farm; however, the first positive evidence of steam power being used to drive a threshing machine was in 1799 in north Yorkshire.cite book | last =Lane | first =Michael R. | title =Pride of the Road (The Pictorial Story of Traction Engines) | publisher =New English Library | date =1976 | pages =p29 | isbn =0 450 03277 9] The next recorded application was in 1812, when Richard Trevithick designed the first 'semi-portable' stationary steam engine for agricultural use, known as a "barn engine". This was a high-pressure, rotative engine with a Cornish boiler, for Sir Christopher Hawkins of Probus, Cornwall. It was used to drive a corn threshing machine and was much cheaper to run than the horses it replaced. Indeed, it was so successful that it remained in use for nearly 70 years, and has been preserved by the Science Museum.cite book | last =Hodge | first =James | title =Richard Trevithick (Lifelines 6) | publisher =Shire Publications | date =1973 | pages =p30 | isbn =0 85263177 4] Although termed 'semi-portable', as they could be transported and installed without being dismantled, these engines were essentially stationary. They were used to drive such barn machinery as pumps and hammer mills, bone-crushers, chaff and turnip cutters, and fixed and mobile threshing drums.

It was not until about 1839 that the truly portable engine appeared, allowing the application of steam power beyond the confines of the farmyard. William Tuxford of Boston, Lincolnshire started manufacture of an engine built around a locomotive-style boiler with horizontal smoke tubes. A single cylinder and the crankshaft were mounted on top of the boiler, and the whole assembly was mounted on four wheels: the front pair being steerable and fitted with shafts for horse-haulage between jobs. A large flywheel was mounted on the crankshaft, and a stout leather belt was used to transfer the drive to the equipment being driven. Several Tuxford engines were displayed at the Royal Agricultural Society's Show at Bristol in 1842, and other manufacturers soon joined in, using the basic design of the Tuxford engine as a pattern for the majority of portable engines produced thereafter.

Early manufacturers in the UK included:
* Alexander Dean of Birmingham
* Ransomes of Ipswich
* William Tuxford and Sons of Boston, Lincolnshire
* Howden of Boston, Lincolnshire
* Clayton & Shuttleworth of Lincoln

This last manufacturer is particularly noteworthy here. The first Clayton & Shuttleworth portable was built in 1845, a two-cylinder engine. In 1852, the company won a gold medal for a portable engine at the Royal Agricultural Society's Gloucester show, and thereafter the business expanded rapidly: they established a second works, in Vienna in 1857, to target the European market, and by 1890 the company had manufactured over 26,000 portable engines, many being exported all over the world.

In the 1850s, John Fowler used a Clayton & Shuttleworth portable engine to drive apparatus in the first public demonstrations of the application of cable haulage to cultivation.

In parallel with the early portable engine development, many engineers attempted to make them self-propelled – the fore-runners of the traction engine. In most cases this was achieved by fitting an additional pinion on the end of the crankshaft, and running a chain from this to another pinion on the rear axle. These experiments met with mixed success.

As noted early on by Thomas Aveling (later of Aveling & Porter fame), it was absurd to use four horses to pull a steam engine from job-to-job, when the engine possessed ten times the strength of the horses.cite book | last =Lane | first =Michael R. | title =Pride of the Road | pages =p56] It was therefore inevitable, once self-propelled traction engines had become sufficiently reliable, that they would take over the roles of many portable engines, and this indeed started to happen from the late 1860s.

However, the portable engine was never completely replaced by the traction engine. Firstly, the portable, having no gearing, was markedly cheaper, and secondly, numerous applications benefitted from a simple steam engine that could be moved, but did not require the additional complexity of one that could move itself.

Small numbers of portables continued to be built even after traction engine production ceased. Robey and Company of Lincoln were still offering portables for sale into the 1960s.

The requirement for a small cheap source of power on farms was largley taken over by the internal combustion stationary engine.

Usage

Apart from threshing work, portable engines were used to drive corn-mills, centrifugal pumps, stone-crushers, dynamos, chaff-cutters and hay-balers. They were even used to generate electricity for floodlighting at football matches, the first instance being at Bramall Lane, Sheffield in 1878. [cite web | last =Simkin | first =John | title =Floodlit Football | work =The Encyclopedia of British Football | publisher =Spartacus Educational | url =http://www.spartacus.schoolnet.co.uk/Ffloodlit.htm | accessdate = 2008-01-04 ]

In general, the portable engine is hauled to the work area, often a farmyard or field, and a long drive belt is fitted between the engine's flywheel and the driving wheel of the equipment to be powered.

In a number of cases, rather than being towed from site-to-site, the portable engine was semi-permanently installed in a building as a stationary steam engine, although the wheels were not necessarilly removed.

A more extreme use occurs where the engine is removed from the boiler and is re-used as a stationary engine. Often, the boiler is also re-used (without its wheels) to provide the steam. As of 2007, there are still examples of such dismantled portable engines working commercially in small rice mills in Burma [cite web | title =Portable Paradise
work =(Examples of portable engines converted to stationary use, in Burma)
date =2007
url =http://www.internationalsteam.co.uk/mills/burmamill16.htm
accessdate = 2008-01-02 ] (and, no doubt, elsewhere too). Such examples are easy to identify due to the curved saddle, below the cylinder block, that was used to mount the engine to the boiler.

Construction

General layout

The most common arrangement follows the original Tuxford design. Although this closely resembles the common layout of a traction engine, the engine of a portable is usually reversed, with the cylinders at the firebox end and the crankshaft at the smokebox end. This layout was designed to position the regulator close to the firebox, making it easier for the engineman to maintain the fire and control the engine speed from the one location. An added bonus is that the flywheel is clear of the rear road wheels so the latter can be set on a narrower track, making the engine easier to manoeuvre through field gates.

A few makers (e.g. Fowler) made their portable engines in the same style as traction engines, with the cylinder at the smokebox end. This was probably to reduce manufacturing costs, as there is no other obvious benefit of doing this. (Thomas Aveling realised that, for a traction engine, it would be better to position the flywheel within reach of the driver in case he carelessly allowed the crank to stop on top dead centrecite book | last =Lane | first =Michael R. | title =Pride of the Road | pages =p58] (where it could not self-start) and most other traction engine manufacturers followed this same idea.)

Boiler

This is usually a fire-tube boiler with a locomotive-type firebox. However, some designs (e.g. the Marshall "Britannia" (pictured)cite web | title =Marshall Britannia portable steam engine, 1914 | publisher =Powerhouse Museum, Sydney, Australia | url =http://www.powerhousemuseum.com/collection/database/index.php?irn=211873&search=steam+engine&
] ) have circular, marine-type, fireboxes. This latter type were also known by British manufacturers as 'colonial' boilers, as they were mainly intended for export to 'the Colonies', and had a high ground clearance for travelling along rough tracks.

Fuel is usually coal but the engine may be designed to use wood fuel, straw or bagasse (sugar cane residue) instead. A longer, circular firebox is particularly suitable for burning logs rather than shorter wood billets. Machines designed for wood-burning may be fitted with spark arrestors.

Engine

Most portable engines are single-cylinder but two-cylinder engines were also built. The slide valve is usually driven by a single eccentric and no reversing gear is fitted. There is usually a belt-driven governor to keep the engine running at constant speed, even if the load fluctuates.

The engine may have one or two flywheels mounted on the same crankshaft. Where two are provided, they are mounted either side of the engine and may be of different diameters. A smaller flywheel provides a slower speed for farmyard work (eg chopping feedstuffs) than is required for driving a threshing machine (for example).

Auxiliaries

The crankshaft drives a boiler feedwater pump which draws water from a barrel placed alongside the engine. Many engines have a simple, but effective, feedwater heater which works by blowing a small portion of the exhaust steam into the water barrel. The barrel also acts as an oil separator. Oil in the exhaust steam rises to the top of the barrel and can be skimmed off.

Chimney

A tall chimney is provided to ensure a good draught for the fire. To permit negotiation of overhead obstacles, the chimney is hinged at its base, and is folded down for transport and storage. A suitably-shaped bracket is usually provided towards the firebox end to support the chimney when folded.

Wheels

Most designs are fitted with four wheels and no suspension of any kind. The first portables had wooden wheels, but as the engines became more powerful (and heavier), fabricated steel wheels were fitted instead.

The 'front' wheels are normally smaller than those at the back. This is because they are mounted on the swivelling "fore-carriage", under the smokebox, and large wheels would be liable to hit the boiler when the engine was turned around a corner. An added bonus is that a larger diameter flywheel may be fitted, providing a more steady power output.

Preservation

Many portable engines still survive, as they were built in large quantities and were shipped to many remote corners of the Earth. A substantial number of them have been preserved, with many restored to full working order: their relatively small size and simpler construction, compared to a traction engine, makes them a much more viable proposition for restoration by the average enthusiast. (That is, provided the boiler is in reasonable condition: boiler repairs can be very expensive; replacement boilers even more so.)

It is usually possible to see portable engines working at traction engine rallies and steam festivals. At the Great Dorset Steam Fair, for example, portable engines may be found in the relevant demonstration areas driving saw benches, threshing machines, rock crushers and other contemporary equipment.

Numerous agricultural and industrial museums include portable engines within their collections.

What is thought to be the oldest surviving Marshall product, works no. 415, a 2.5 nhp portable from 1866, may be seen at the Turon Technology Museum (Museum of Power), in New South Wales. This engine is also the oldest "documented" portable in Australia.cite web | title =Gallery 1 – Steam engines | publisher =Turon Technology Museum (Museum of Power) | url =http://www.hermes.net.au/turon/gallery1.htm | accessdate =2008-01-04 ]

ee also

* Farm equipment
* List of traction engine manufacturers – "many traction engine manufacturers also built portable engines"

References

Further reading

* "Portable Steam Engines" (Shire Album 163) by Lyndon R. Shearman, published by Shire Publications Ltd, ISBN 0 85263 783 7
* "The Portable Steam Engine: Its Construction and Management – A Practical Manual for Owners and Users of Steam Engines Generally" by W. D. Wansbrough, 168 pages, published by TEE Publishing Ltd (1994), ISBN 1857610679
(This is a modern reprint of a book originally published in 1887 or 1911, depending on which online bookseller you refer to!.)

External links

* [http://www.steamscenes.org.uk/?pc=%2Fsearch%2FtextResults%2F&ssq=portable Steam Scenes – extensive searchable photo library] – "preserved portable engines in the UK, Europe, Australia and New Zealand"
* [http://www.nelmes.fsnet.co.uk/paxman/paxports.htm List (and details) of surviving Paxman portable engines]
* [http://www.dalefield.com/nzfmm/magazine/Portable_Engine.html Scale model built from Meccano] , "with close-up pictures showing the components of a typical portable engine."
* [http://www.steamengine.com.au/steam/restore/arthur/index.html Restoration of a derelict 1904 Ruston Proctor portable (in Australia)] – "Employed some unusual solutions, including design of a new pressure vessel to fit "inside" the original, unrepairable, boiler shell."