- Schottky diode
The Schottky diode (named after German physicist
Walter H. Schottky; also known as hot carrier diode) is a semiconductor diodewith a low forward voltage drop and a very fast switching action.
In the early days of wireless,
cat's-whisker detectors were used. They can be considered as primitive Schottky diodes.
A Schottky diode uses a metal-semiconductor junction as a
Schottky barrier(instead of a semiconductor-semiconductor junction as in conventional diodes). This Schottky barrier results in both very fast switching times and low forward voltage drop. A Schottky diode is a special type of diode with a very low forward-voltage drop. When current flows through a diode, it has some internal resistance to that current flow, which causes a small voltage drop across the diode terminals. A normal diode has between 0.7-1.7 volt drops, while a Schottky diode voltage drop is between approximately 0.15-0.45 – this lower voltage drop translates into higher system efficiency.
The most important difference between p-n and Schottky diode is reverse recovery time, when the diode switches from non-conducting to conducting state and vice versa. Where in a p-n diode the reverse recovery time can be in the order of hundreds of nanoseconds and less than 100ns for fast diodes, Schottky diodes do not have a recovery time, as there is nothing to recover from. The switching time is ~100 ps for the small signal diodes, and up to tens of nanoseconds for special high-capacity power diodes. With p-n junction switching, there is also a reverse recovery current, which in high-power semiconductors brings increased EMI noise. With Schottky diodes switching instantly with only slight capacitive loading, this is much less of a concern.
It is often said that the Schottky diode is a "
majority carrier" semiconductor device. This means that if the semiconductor body is doped n-type, only the n-type carriers (mobile electrons) play a significant role in normal operation of the device. The majority carriers are quickly injected into the conduction band of the metal contact on the other side of the diode to become free moving electrons. Therefore no slow, random recombination of n- and p- type carriers is involved, so that this diode can cease conduction faster than an ordinary p-n rectifier diode. This property in turn allows a smaller device area, which also makes for a faster transition. This is another reason why Schottky diodes are useful in switch-mode power converters; the high speed of the diode means that the circuit can operate at frequencies in the range 200 kHz to 2 MHz, allowing the use of small inductors and capacitors with greater efficiency than would be possible with other diode types. Small-area Schottky diodes are the heart of RF detectors and mixers, which often operate up to 5 GHz.
The most evident limitations of Schottky diodes are the relatively low reverse voltage rating for silicon-metal schottky diodes, 50 V and below, and a relatively high
reverse leakage current. The reverse leakage current, increasing with temperature, leads to a thermal instability issue. This often limits the useful reverse voltage to well below the actual rating. Luckily the diodes are becoming better and better. The voltage ratings are now up at 200 V.
Since 2001 another important invention was presented by Siemens Semiconductor (now
Infineon): a silicon carbideSchottky diode. SiC Schottky diodes have about 40 times lower reverse leakage current compared to siliconschottky diodes and are available in 300V and 600V variants. As of 2007 a new 1200 volt 7.5A variant is sold as 2x2mm chip for power invertermanufacturers.
Silicon carbide has a high thermal conductivity and temperature has little influence on its switching and thermal characteristics. With special packaging it is possible to have operating junction temperatures of over 500K, which allows passive radiation cooling in
Typical applications include discharge-protection for
solar cells connected to lead-acid batteries and in switched-mode power supplies; in both cases the low forward voltage leads to increased efficiency. While standard silicon diodes have a forward voltage drop of about 0.7 volts and germanium diodes 0.3 volts, Schottky diodes voltage drop at forward biases of around 1 mA is in the range 0.15 V to 0.46 V, Fact|date=July 2008 which makes them useful in voltage clamping applications and prevention of transistor saturation. This is due to the higher current densityin the Schottky diode.
Schottky diodes can be used in power supply "OR"ing circuits in products that have both an internal battery and a
mains adaptorinput, or similar. However, the high reverse leakage current presents a problem in this case, as any high-impedance voltage sensing circuit (e.g. monitoring the battery voltage or detecting whether a mains adaptor is present) will see the voltage from the other power source through the diode leakage.
Commonly encountered Schottky diodes include the 1N5817 series 1 A rectifiers. Schottky metal-semiconductor junctions are featured in the successors to the
7400 TTLfamily of logic devices, the 74S, 74LS and 74ALS series, where they are employed as clamps in parallel with the collector-base junctions of the bipolar transistors to prevent their saturation, thereby greatly reducing their turn-off delays.
When an even lower forward voltage is desired, or if the reverse-leakage is problematic, a so-called "
ideal diode", combining a MOSFETswitch and a control circuit, can be used, in an operation mode known as synchronous rectification.
* [http://www.mtmi.vu.lt/pfk/funkc_dariniai/diod/schottky.htm The Metal-Semiconductor Junction. Schottky Diode.]
* [http://www.onsemi.com/PowerSolutions/product.do?id=MBR40250 ON Semiconductor MBR40250 40A/250V Schottky Diode]
* [http://www.infineon.com/cgi-bin/ifx/portal/ep/channelView.do?channelId=-64628&channelPage=%2Fep%2Fchannel%2FleafNote.jsp&pageTypeId=17099 Infineon 300V/600V SiC Schottky diodes for power applications]
* [http://www.microsemi.com/micnotes/401.pdf "Introduction to Schottky Rectifiers"]
* [http://www.cree.com/products/power_docs2.asp "CREE Power Devices Product Specifications"]
* [http://www.ixyspower.com/images/technical_support/Application%20Notes%20By%20Topic/FREDs,%20Schottky%20and%20GaAS%20Diodes/IXAN0042.pdf "Is the lowest forward voltagedrop of real schottky diodes always the best choice?"] Technical application, IXYS Corp.
Wikimedia Foundation. 2010.