Saltillo tile

Saltillo tile is one of the two most famous products of the Mexican city of Saltillo, Coahuila. (The other is the multi-coloured woven "serapes" so typical of the region.) Saltillo tiles vary in colour and shape, but the majority range from in varying hues of reds, oranges and yellows. Tiles are shaped either by pressing quarried clay with a wooden frame (super), or carving out the desired shape (regular). Depending on the raw tile's placement among other tiles at the time of firing, its colour ranges from yellow to a rich orange. Saltillo tile is highly porous, and soaks in liquid easily. Unlike most ceramic tile, there is no glaze on the top surface of the tile. It is difficult to install as it absorbs water from the thin-set mortar, grout, wax pencils, etc. Once placed, it stains and scuffs easily if not properly sealed and maintained with a quality sealer. Saltillo is probably a poor choice for outdoor installation in freeze-thaw climates, although is a popular choice in warmer climates. During installation the tiles should be handled carefully to avoid stains that can even occur from body oils on the installer's hands.

Preferred methods for installation invariably relate to its propensity for soaking in liquid. One method involves soaking the tile in water, setting the tile with thin-set mortar, grouting, then sealing both the saltillo and the grout with a quality surface sealer. However, using this method may cause the grout to stick to the surface of the saltillo tile, making it impossible to remove. This method is NOT recommended for do-it-yourselfers.

Another method involves soaking the tile, setting the tile then allowing it to dry, sealing the tile, then grouting. This method prevents the grout from sticking to the tile.

You might ask if it's possible to seal just the top of the tile before setting...the problem is that soaking the tile allows it to bond more strongly with the mortar, and you probably don't want to seal the tile, then soak it in water.

A penetrating sealer will maintain the natural look of the tile. You should periodically test the seal by putting a few drops of water on the tile in various places. If the water is absorbed, then another coat of sealer should be applied.

Other surface sealers may give the tile a shiny appearance. As the tile loses its shine, another coat is applied on top of the old sealer. If the finish becomes too worn or uneven, it can be stripped and a new coat applied. However this option is very labor intensive.

Additionally, another coat of sealer can be used on both the saltillo tile and grout. Although inexpensive itself, saltillo is very expensive to have installed. A professional with experience in saltillo will charge $4.50 to $6.00 per square foot for installation, depending on your locale.

Treatments for saltillo include: coating them with a surface sealer prior to grouting (as mentioned earlier), applying an admixture of linseed oil and paint thinner, applying natural stone colour enhancers, applying floor hardeners, applying shine, painting them with a water-based paint, coating them with wood stain, etc. As the tile is incredibly porous it will readily absorb just about any liquid. Please note any of these treatments may be used on the tile, however some of them such as penetrating sealers, enhancers or linseed oil treatments penetrate into the tile and may affect the ability of later coatings to adhere to the tile.

Saltillo tile may be sealed with a penetrating sealer or a film forming sealer (coating). A film forming sealer will leave a film on the surface of the tile. With multiple coats the film will build an even protective film and gloss that may repel water, oil, grease and efflorescence. A quality acrylic sealer, such as OLE Mexican Tile sealer from Glaze-n-Seal Products, should be used as it will be easy to apply, non-yellowing and long lasting. A quality acrylic floor polish can be applied over the sealed surface for added abrasion and wear protection.

The finished sealed floor should be maintained for best results. For routine cleaning use a neutral cleaner to damp mop the floor (never flood the sealed floor with water). Reapply the polish if areas begin to show wear over time. Maintaining the sealer/polish will greatly extend the life of the sealer and minimize repair needs

External links

* [http://www.johnbridge.com/Saltillo%20Tiles.htm Saltillo tile information]
* [http://www.theflooringlady.com/saltillo_tile.html Saltillo tile forum]