Bulleid chain-driven valve gear

Bulleid chain-driven valve gear

, and were based upon motor-vehicle practice in an attempt to create a compact, but efficient design with a minimum of service requirements.

Design principles

Oliver Bulleid's decision to have three cylinders, all driving the middle coupled axle of his Merchant Navy, West Country and Battle of Britain Classes, gave rise to several problems. As each cylinder was to have its own separate valve gear, this left very little space for the conventional inside set of motion. [cite book| author=Bulleid, H. A. V.| title=Bulleid of the Southern| location=Hinckley| publisher=Ian Allan Publishing| year=1977| isbn=071100689X| ] This prompted Oliver Bulleid's attempt to design a new miniaturised Walschaerts motion layout that was compact enough to enclose the whole system in a casing. All three sets of valve gear were worked from an auxiliary three-throw crankshaft [cite book| author=Bulleid, H. A. V.| title=Bulleid of the Southern| pages=p 56| ] driven from the driving axle by triple chains through an idler gear. The auxiliary crankshaft drove both eccentric rods and combination levers displacing the piston valves; these were of the outside admission type. [cite book| author=Day-Lewis, S| title=Bulleid, Last Giant of Steam| location=London| publisher=George Allen & Unwin| year=1964| pages=p 148| ] The valve heads were connected by a double girder arrangement each actuated by a vertical rocking shaft located between the two girders and midway between the two heads with a further connecting link pivoted just behind the valve head nearest the front. A sealed oscillating shaft drove the offset upper rocker arm and link and that whole assembly worked inside the exhaust space of the steam chest. The advantage of having admission steam working on the outside faces of the valves meant that the volume under maximum pressure was completely sealed at the ends with no glands susceptible to leakage.

Valve motion and the inside connecting rod were enclosed in an oil bath consisting of a vertical steel box located between the main frame members. About 2 inches (50 mm) depth of oil lay in the bath, the inside big end was splash-lubricated and a pump sprayed the various valve motion pins.cite book| author=Bulleid, H. A. V.| title=Bulleid of the Southern| pages=p 57| ] None of this was particularly revolutionary, being borrowed from internal-combustion engine practice and for use with steam it was established practice at the Sentinel Waggon Works. It was thought that the arrangement would obviate the daily need to oil all moving parts and as they were protected from the elements, they should be able to run 100,000 miles (160,000 km) without attention. It was this consideration that meant the continued use of the system, albeit in modified form on Bulleid's Leader Class.

Problems

In practice, though, the arrangement had a number of disadvantages. Cracks developed in the oil bath casing due to incorrect welding procedure. Condensation caused corrosion, and oil leaked out through inadequate seals, causing wheelslip and fire hazards. [cite book| author=Reed, Brian| title=Loco Profile no 22, "Merchant Navy Pacifics"| publisher=Profile Publications| location=Windsor, UK| pages=p 231| ] Valve timing was highly unpredictable; this has been attributed to chain stretch, although Bulleid claimed that it was allowed for. A more likely cause may have been geometrical due to the sequential proportions of levers, especially the final rockers transmitting the limited movement of the "miniaturised" valve gear to the union link driving the long travel piston valve; this "anti-lever" alone would have made accurate valve timing difficult to achieve and given rise to stress in the drive mechanism. Wear developing in the pin joints could only have exacerbated this lack of precision making chain wear more of a consequence than the cause of the problem. A further complication was the unpredictable behaviour of the Eastleigh type of steam reverser employed. If this reverser misbehaved under the fluctuating pressures present in the steam chest, the locomotive seemed to have a will of its own.cite video| title=Bulleids in Retrospect| publisher=Transport Video Publishing| location=Wheathampstead, Hertfordshire| ] For example, if the reverser dropped into full gear, the slackness in the motion would make the valves overrun their designed full travel inside the cylinders. This would result in the locomotive taking off like an unleashed race horse, high coal consumption, throwing the fire out of the chimney and running the risk of a violent high-speed slipping.

These problems combined contributed to the gear's eventual replacement by three sets of Walschaerts gear mounted in the conventional manner.

Footnotes


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Valve gear — The valve gear of a steam engine is the mechanism that operates the inlet and exhaust valves to admit steam into the cylinder and allow exhaust steam to escape, respectively, at the correct points in the cycle. It is sometimes referred to as the… …   Wikipedia

  • Oliver Bulleid — Oliver Vaughan Snell Bulleid (19 September 1882 25 April 1970) was a British railway and mechanical engineer best known as the Chief Mechanical Engineer (CME) of the Southern Railway between 1937 and the 1948 nationalisation, developing many well …   Wikipedia

  • SR West Country and Battle of Britain Classes — Infobox Locomotive powertype=Steam name = SR Un rebuilt West Country/Battle of Britain Classes Herring, pp. 160 ndash;161] caption = Un rebuilt West Country Class 21C123 Blackmoor Vale , as preserved, in Southern Railway Malachite Green and… …   Wikipedia

  • Southern Railway (Great Britain) — The Southern Railway (SR), was a British railway company established in the 1923 Grouping. It contained notable examples of civil engineering, linking London with the Channel ports, South West England and Kent. The railway was formed by the… …   Wikipedia

  • SR Merchant Navy class — SR Merchant Navy class[1] Official Southern Railway photograph of 21C1 Channe …   Wikipedia

  • SR Merchant Navy Class — Infobox Locomotive powertype=Steam name = SR Merchant Navy ClassHarvey] caption = Official Southern Railway photograph of 21C1 Channel Packet as built, 1941. designer = Oliver Bulleid builder = SR Eastleigh Works builddate = 1941 ndash;1949… …   Wikipedia

  • SR Leader Class — Infobox Locomotive powertype=Steam name = SR/BR Leader Class Robertson, Kevin: The Leader Project: Fiasco or Triumph? (Oxford: Oxford Publishing Company, 2007) ISBN 0860936066] caption = 36001 at Oxted, taken by British Railways designer = Oliver …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”