Stroker Kit

Stroker Kit

A Stroker kit is an aftermarket assembly that increases the displacement of a reciprocating engine by increasing the travel of the piston (that is, the piston moves further up and/or down in the cylinder). This is done by using a different crankshaft where the crank pin is moved further away from the center of the axis of rotation of the crankshaft. While this increases displacement and torque it can potentially lower the limit to which the motor can rev safely compared to the stock configuration.

Differences from original equipment manufacturer (OEM) configurations

Two key characteristics differentiate stroker kits from OEM rotating assemblies.

First, and most important, the crankshaft's rod journals are physically farther from the main journals than on the original equipment. A given extension in the distance between the rod and main journals results in twice that distance in increase of piston travel. For example, in a Chrysler LA (1971-1992) 360 cubic inch (5.9 l) V8, the rod journal centerline is 1.79 in (4.55 cm) from the main journal centerline. The piston travels 3.58 in (9.1 cm) in this configuration. When this engine is modified with a 402 cubic inch (6.6 l) stroker kit, the distance between the main journal centerline and the rod journal centerline is increased to 2.00 in (5.08 cm), which results in the piston travelling 4.00 in (10.16 cm). So, the modified crankshaft with 0.21 in (0.53 cm) further distance between the main and rod journals results in 42 cubic inches (.7 ) of displacement greater than the engine had before.

The second key characteristic of a stroker kit versus OEM is the required changes to allow a stroked crank to 'fit'. This is accomplished in one of three ways:

ONE: Location of the piston pin (and the top of the rod) within the piston, or the "compression height" is shortened. TWO: Length of the rod is shortened.THREE: Height of the cylinder is lengthened.

Option One - Shorter Piston:The stock Chrysler LA engine in the example above has a main to rod bearing centerline distance of 1.79 in (4.55 cm), a rod that is 6.123 in (15.55 cm) long, and a piston that is 1.67 in from piston pin centerline to top, depending on the application. As the engine stroke is increased in the example above, the 402 cubic inch (6.6 l) configuration would place the piston 0.21 in (0.53 cm) higher in the cylinder at top dead center, and with a distance of 9.585 in (24.36 cm) from crankshaft main centerline to deck, the piston would protrude about 0.21 in (0.53 cm) higher than the top deck, or would collide with the cylinder head combustion chamber. To offset this, aftermarket pistons relocate the piston pin higher within the piston itself. This change in compression height leaves the piston with 1.462 in (3.714 cm) of material in the top portion of the piston, instead of 1.672 in (4.247 cm) as is stock.

Option Two - Shorter Rod:Powroll is a company that has offered stroked cranks for single-cylinder motorcycles and ATV's since the early 1960's. Their stroke process involves installing an offset bushing in the stock crank weights to move the crank pin location further out from centerline - increasing the stroke.

Most Powroll stroked cranks also utilize a radical process they invented called a 'shrunk rod'. A proprietary process, rod shrinking evidently involves heat and pressure to compress it to a height 1/2 the distance of the stroke increase, thus bringing the piston deck height back to original.

This process allows for the use of any stock or aftermarket piston already manufactured for that particular model, without the need of a spacer plate or piston modification.

The Powroll stroke process usually costs much less than purchasing a new crank assembly; it also uses OEM components, which have known properties and reliability.

Images of how a stroked crank works

*Stock Crank:
*Stroked Crank:

Advantages of a stroked crank

A stroked crank increases displacement, and also uses leverage to make torque more easily.

An engine with a stroked crank will usually make more overall horsepower than an engine with a bore kit with the same displacement increase.

Disadvantages of a stroked crank

Increased stroke makes the piston travel further up and down. Since the amount of time allowed for this movement is not increased, the piston speed increases with a stroked crank (piston must move a further distance in the same amount of time). This can sometimes cause pistons to wear more quickly.

Large increases in stroke can decrease an engine's ability to perform optimally at high rpm. Engines used at sustained high rpm usually will be better with less stroke and more bore (oversquare).

Obtaining a stroked crank

Purchase a new stroked crankshaft from an aftermarket or OEM source:A typical complete stroker kit is comprised of the crankshaft, connecting rods, pistons, piston pins, main bearings, rod bearings, and piston rings. This assembly is also called "the rotating assembly" or "the bottom end". Many different types of each of the components can be used for different applications. Crankshafts, for example, may be either of forged or of cast manufacture. Rods may consist of I-beam or H-beam rods made of various materials, from steel to titanium. Rods may be stock length (requiring the use of either shorter pistons, or taller cylinders), or shorter length (usually utilizing stock height pistons and cylinders).

Modify a stock crankshaft for increased strokeSome stock crankshafts can also be modified to increase stroke. This is typically more cost effective for single cylinder motorcycle and ATV engines.

External links

* [http://www.powroll.com/tech_specs_stroker_howitworks.htm Powroll stroke explanation webpage]


Wikimedia Foundation. 2010.

Нужна курсовая?

Look at other dictionaries:

  • Nissan CA engine — Manufacturer Nissan Motors Production 1982 1991 Predecessor Nissan L engine Nissan Z engine Successor Nissan SR engine (all except CA16) Nissan GA engine (CA16) …   Wikipedia

  • Holden Special Vehicles — Type Private Industry Automotive Founded 1988 Founder(s) Tom Walkinshaw …   Wikipedia

  • Lamborghini Diablo — Manufacturer Lamborghini Production 1990–2001 2884 produced[1] …   Wikipedia

  • Chevrolet Corvair engine — Corvair engine Manufacturer Chevrolet Displacement 140 CID (2.3L), 145 CID (2.4L), 164 CID (2.7L) Cylinder block alloy …   Wikipedia

  • AC Cobra — Shelby Cobra redirects here. For the 2004 Ford Shelby Cobra Concept, see Ford Shelby Cobra Concept. AC Cobra Manufacturer AC Cars Also called Shelby Cobra …   Wikipedia

  • Ford Y-block engine — Infobox Automobile engine name=Ford Y block V8 manufacturer=Ford Motor Company production=1954 ndash;1964 predecessor=Ford L Head engine successor=Ford FE engine Ford Windsor engine Ford 335 Cleveland V8 class=Small block OHV V8 similar=Chevrolet …   Wikipedia

  • Flash animation — Simple animation in Flash MX; a square moving across the screen in a motion tween, one of the basic functions of Flash. Onion skinning is used to show the apparent motion of the square. A Flash animation or Flash cartoon is an animated film which …   Wikipedia

  • Mark Camacho — Born April 12, 1964 (1964 04 12) (age 47) Montreal, Quebec Mark Camacho (born April 12, 1964) is a Canadian actor who has starred in many films, and more notably, some voice acting roles, such as Oliver Frensky in Arthur, Lyle in Animal… …   Wikipedia

  • List of Freaks and Geeks characters — The following is a list of characters from the television series Freaks and Geeks. Contents 1 Weirs 1.1 Lindsay Weir 1.2 Sam Weir 1.3 Harold Weir …   Wikipedia

  • Harley-Davidson VRSC — Infobox Motorcycle left name=Harley Davidson VRSC aka=V Rod manufacturer=Harley Davidson production=2002 ndash;Present class = power cruiser related= wheelbase=in to mm|67.2 length=in to mm|94.4 width= height= seat height=in to mm|27.1… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”