Pockels effect

The Pockels effect, or Pockels electro-optic effect, produces birefringence in an optical medium induced by a constant or varying electric field. It is distinguished from the Kerr effect by the fact that the birefringence is proportional to the electric field, whereas in the Kerr effect it is quadratic in the field. The Pockels effect occurs only in crystals that lack inversion symmetry, such as lithium niobate or gallium arsenide and in other noncentrosymmetric media such as electric-field poled polymers or glasses.

Friedrich Carl Alwin Pockels studied the effect which bears his name in 1893.

Pockels cells

The Pockels effect is used to make Pockels cells, which are voltage-controlled wave plates.

The electric field can be applied to the crystal medium either longitudinally or transversely to the light beam. Longitudinal Pockels cells need transparent or ring electrodes. Transverse voltage requirements can be reduced by lengthening the crystal.

Alignment of the crystal axis with the ray axis is critical. Misalignment leads to birefringence and to a large phase shift across the long crystal. This leads to polarization rotation if the alignment is not exactly parallel or perpendicular to the polarization.A transverse cell consists of two crystals in opposite orientation, which give a zero order wave plate when voltage is turned off. This is often not perfect and drifts with temperature. But the mechanical alignment of the crystal axis is not so critical and is often done by hand without screws; while misalignment leads to some energy in the wrong ray (either e or o -- for example, horizontal or vertical), in contrast to the longitudinal case, the loss is not amplified through the length of the crystal.

Pockels cells may be used to rotate the polarization of a passing beam. See Applications below for uses.

Dynamics within the cell

Due to the high relative dielectric constant of about 36 of the crystal electric field changes propagate only with c/6. Fast non fiber optic cells are thus embedded into a matched transmission line. Putting it at the end of a transmission line leads to reflections and doubled switching time. The signal from the driver is split into parallel lines which lead to both ends of the crystal, when they meet in the crystal their voltages add up.Pockels cells for fibre optics may employ a traveling wave design to reduce current requirements and increase speed.

Usable crystals also exhibit the piezoelectric effect to some degree (RTP has the lowest, BBO and Lithium niobate are high), after a voltage change sound waves start propagating from the sides of the crystal to the middle. This is not important for pulse pickers, but for boxcar windows. Guard space between the light and the faces of the crystals needs to be larger for longer holding times.Behind the sound wave the crystal stays deformed in the equilibrium position for the high electric field.This increases the polarization. Due to the growing of the polarized volume the electric field in the crystal in front of the wave increaseslinearly, or the driver has to provide a constant current leakage.

The driver electronics

The driver must withstand the doubled voltage returned to it. Pockels cells behave like a capacitor. When switching these to high voltage a high charge is needed; consequently, 3 ns switching requires about 40 A for a 5 mm aperture.Shorter cables reduce the amount of charged wasted into the it.

The driver may employ a lot transistors connected parallel and serial.The transistors are floating and need DC isolation for their gates.So either the gate signal is send via optical fiber or the gates are driven by a large transformerwith careful compensation for feedback to prevent oscillation.

The driver may employ a cascade of transistors and a triode.In a classic, commercial circuit the last transistor is an IRF830 Mosfet and the triode is a Eimac Y690 triode.The setup with a single triode has the lowest capacity, this even justifies turning off the cell by applying the double voltage.A resistor ensures the leakage current needed by the crystal and later to recharge the storage capacitor.The Y690 switches up to 10 kV and the cathode delivers 40 A if the grid is on +400 V.In this case the grid current is 8 A and the input impedance is thus 50 Ohm, which matches standard coaxial cables, and the Mosfet can thus placed remotely. Some of the 50 Ohm is spent on an additional resistor which pulls the bias on -100 V.The IRF can switch 500 Volts. It can deliver 18 A pulsed.Its leads function as an inductance, a storage capacitor is employed, the 50 Ohm coax cable is connected, the Mosfet has an internal resistance,and in the end this is a critically damped RLC circuit, which is fired by a pulse to the gate of the Mosfet.

The gate needs 5 V pulses (range: +-20 V) while provided with 22 nC.Thus the current gain of this transistor is one for 3 ns switching, but it still has voltage gain.Thus it could theoretically also be used in common gate configuration and not in common source configuration.Transistors, which switch 40 V are typically faster, so in the previous stage a current gain is possible.

And then there the little problem, that the IRF delivers a negative pulse, but the Y690 needs a positive pulse,which is solved by a transformer.

Applications of Pockels cells

Pockels cells are used in a variety of scientific and technical applications:

*A Pockels cell, combined with a polarizer, can be used for a variety of applications. Switching between no optical rotation and 90° rotation creates a fast shutter capable of "opening" and "closing" in nanoseconds. The same technique can be used to impress information on the beam by modulating the rotation between 0° and 90°; the exiting beam's intensity, when viewed through the polarizer, contains an amplitude-modulated signal.
* Preventing the feedback of a laser cavity by using a polarizing prism. This prevents optical amplification by directing light of a certain polarization out of the cavity. Because of this, the gain medium is pumped to a highly excited state. When the medium has become saturated by energy, the Pockels cell is switched, and the intracavity light is allowed to exit. This creates a very fast, high intensity pulse. Q-switching, chirped pulse amplification, and cavity dumping use this technique.
* Pockels cells can be used for quantum key distribution by polarizing photons.
* Pockels cells in conjunction with other EO elements can be combined to form electro-optic probes.
* A Pockels Cell was used by MCA Disco-Vision (DiscoVision) engineers in the optical videodisc mastering system - light from an Argon-Ion laser was passed through the Pockels Cell to create pulse modulations corresponding to the original FM video and audio signals to be recorded on the master videodisc. MCA used the Pockels Cell in videodisc mastering up until the sell-out to Pioneer Electronics. To increase the quality of the disc recordings, MCA patented a Pockels Cell stabilizer that reduced the 2nd Harmonic Distortion that could be created by the Pockels Cell during mastering. MCA used either a DRAW (Direct Read After Write) mastering system or a Photoresist system. The DRAW system was their originally preferred embodiment since it allowed non-clean room conditions during disc recording and instant checking of the disc quality during mastering. The original single-sided test pressings from 1976/77 were mastered with the DRAW system as were the "educational", non-feature titles at the formats release in December of 1978.

ee also

* Electro-optic modulator
* Acousto-optic modulator