Throttle position sensor

Throttle position sensor

A throttle position sensor (TPS) is a sensor used to monitor the position of the throttle in an internal combustion engine. The sensor is usually located on the butterfly spindle so that it can directly monitor the position of the throttle valve butterfly.

The sensor is usually a potentiometer, and therefore provides a variable resistance dependent upon the position of the butterfly valve (and hence throttle position).

The sensor signal is used by the engine control unit (ECU) as an input to its control system. The ignition timing and fuel injection timing (and potentially other parameters) are altered depending upon the position of the throttle, and also depending on the rate of change of that position. For example, in fuel injected engines, in order to avoid stalling, extra fuel may be injected if the throttle is opened rapidly (mimicking the accelerator pump of carburetor systems).

More advanced forms of the sensor are also used, for example an extra "closed throttle position sensor" (CTPS) may be employed to indicate that the throttle is completely closed.

Some ECUs also control the throttle position and if that is done the position sensor is utilised in a feedback loop to enable that control.

Related to the TPS are accelerator pedal sensors, which often include a wide open throttle (WOT) sensor. The accelerator pedal sensors are used in "drive by wire" systems, and the most common use of a wide open throttle sensor is for the kickdown function on automatic transmissions.

Modern days sensors are Non Contact type, wherein a Magnet and a Hall Sensor is used. In the potentiometric type sensors, two metal parts are in contact with each other, while the butterfly valve is turned from zero to WOT, there is a change in the resistance and this change is resistance is given as the input to the ECU.

Non Contact type TPS work on the principle of Hall Effect, wherein the magnet is the dynamic part which mounted on the butterfly valve spindle and the hall sensor is mounted with the body and is stationary. When the magnet mounted on the spindle which is rotated from zero to WOT, there is a change in the magnetic field for the hall sensor. The change in the magnetic field is sensed by the hall sensor and the hall voltage generated is given as the input to the ECU. Normally a two pole magnet is used for TPS and he magnet may be of Diametrical type or Ring type or segment type, however the magnet is defined to have a certain magnetic field.

ee also

* list of sensors


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • throttle position sensor — (TPS) A potentiometric fuel injection switch with two contacts for the two end positions of the throttle valve, which sends a signal to the electronic control unit when the throttle valve is closed (idle) or wide open (full load). The sensor… …   Dictionary of automotive terms

  • position sensor — See crankshaft position sensor throttle position sensor …   Dictionary of automotive terms

  • Throttle body — In a fuel injection engine, the throttle body is the part of the air intake system that controls the amount of air flowing into the engine, in response to driver input. While the accelerator is often called a gas pedal , it would be more accurate …   Wikipedia

  • sensor — [1] An electronic detection device that receives and reacts to a signal, such as a change in voltage, temperature or pressure. [2] Material or device which goes through physical change or electronic characteristic change as surrounding conditions …   Dictionary of automotive terms

  • throttle valve switch — See throttle position sensor …   Dictionary of automotive terms

  • Electronic throttle control — (ETC) is an automobile technology which severs the mechanical link between the accelerator pedal and the throttle. Most automobiles already use a throttle position sensor (TPS) to provide input to traction control, antilock brakes, fuel injection …   Wikipedia

  • sensor plate — A plate in the mixture control unit of a CIS, attached to a lever that operates the control plunger in the fuel distributor; the sensor plate position is governed by the amount of air admitted to the engine via the throttle valve and auxiliary… …   Dictionary of automotive terms

  • Fuel injection — Fuel rail connected to the injectors that are mounted just above the intake manifold on a four cylinder engine. Fuel injection …   Wikipedia

  • Trionic T5.5 — Engine management system SAAB TRIONIC T5.5 Courtesy of: DrBoost Overview Saab Trionic T.5.5 is an engine management system that controls ignition, fuel injection and turbo boost pressure. The system was introduced in 1994 Saab 900 with B204L… …   Wikipedia

  • Engine control unit — An engine control unit (ECU) is an electronic control unit which controls various aspects of an internal combustion engine s operation. The simplest ECUs control only the quantity of fuel injected into each cylinder each engine cycle. More… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”