Measurement category

Measurement category
Schematic representation of measurement categories

Measurement category - a method of classification of live electric circuits used in measurement and testing of installations and equipment, usually in the relation within a building (residential or industrial).

The categories take into account the total continuous energy available at the given point of circuit, and the occurrence of impulse voltages. The energy can be limited by circuit breakers or fuses, and the impulse voltages by the nominal level of voltage.

Contents

Measurement categories

The definitions for each measurement category are as follows.[1]

There are four categories, which are always stated with the designated voltage, for instance "CAT III, 150 V" or "CAT IV, 1000 V". This has important safety implications for impulse voltages and insulation clearances.

CAT I

CAT I is applicable to instruments and equipment, which are not intended to be connected to the mains supply.

Because the available energy is very limited, this category is normally not marked on the equipment - instead simply rated voltages and currents are stated (e.g. in multimeters).

Examples: low voltage electronic circuits, load circuits of bench power supplies, etc.

CAT II

CAT II defines circuits which are intended for direct connection into mains sockets or similar points. The energy in such installations should be limited to below 100 A continuously (or below 500 A for voltages not exceeding 150 V).

The maximum available continuous power must be limited (for instance by a circuit breaker) to not more than 22 000 VA.

Example: a device connected to a 240 V mains socket with 13 A fuse (energy limited to 3100 VA)

CAT III

CAT III is for circuits which can be connected to the mains installation of a building. Energy is limited by circuit breakers to less than 110 000 VA with the current not exceeding 11 000 A.

Example: 110/240 V distribution boards, busbars, or equipment permanently connected to the 3-phase power supply (e.g. electric motors).

CAT IV

CAT IV includes circuits which are connected directly to the source of power for a given building. There are very high levels of available energy (e.g. limited only by the power transformer) and arc flash can occur.

Example: measurements on a cable connecting the power transformer and a building (i.e. before the circuit breakers in the building).

Clearances

The value of clearance relates to the electrical insulation, and the possibility of arc flash between two electrically energised parts (or between live and grounded parts). Higher voltages require higher clearances. For double insulation the clearances must be doubled.

The required values can vary from 0.04 mm for single insulation CAT II, 50 V, to 28 mm for double insulation CAT IV, 1000 V. The exact values are defined in the international standards.[1] Such standards should be followed rigorously during the design process of the appropriate equipment.

Impulse withstand voltages

Similarly to the clearances the value of required impulse withstand voltage varies from 500 V (CAT II, 50 V), to 12 000 V (CAT IV, 1000 V).

References

  1. ^ a b IEC 61010-20-030, Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 30 Special requirements for testing and measuring circuits

Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Measurement and Evaluation in Counseling and Development —   Language English …   Wikipedia

  • measurement — raises four main issues for the sociologist: representation (how many properties of the empirical world can best be modelled?); uniqueness (how unique are the resulting measurement numbers?); appropriate statistics (what indices may legitimately… …   Dictionary of sociology

  • category — (cat)    the ranking of a hurricane on the Saffir Simpson scale, used by the U.S. National Weather Service. A somewhat different scale of categories is used for tropical cyclones by the Australian Bureau of Meterology …   Dictionary of units of measurement

  • Measurement while drilling — Well logging Gamma ray logging Spontaneous potential logging Resistivity logging Density logging Sonic logging Caliper logging Mud logging LWD/MWD v · …   Wikipedia

  • measurement by fiat — Procedures for quantification of data which make no claim to be representational measurement , but rather assign numbers on the basis of arbitrary units, face validity, or intuition. This often happens when sociologists refer to a concept which… …   Dictionary of sociology

  • category — A key aspect of the measurement process involves placing observations of measurements into groups or categories on the basis of unequivocally shared features. Hence a category is a homogeneous grouping of data. For example, the variable ‘sex’… …   Dictionary of sociology

  • drought severity category — (D)    a measure of drought severity developed by the U.S. National Drought Mitigation Center and used widely by other agencies in the U.S. Categories are denoted D0 D5, with higher numbers indicating more severe drought. A table is provided …   Dictionary of units of measurement

  • Saffir-Simpson category —    a ranking of the strength of a hurricane, introduced by two American meteorologists and used by the U.S. National Weather Service to rank storms in the Atlantic and northeastern Pacific Oceans. A complete description, from the U.S. Atlantic… …   Dictionary of units of measurement

  • radiation measurement — ▪ technology Introduction       technique for detecting the intensity and characteristics of ionizing radiation, such as alpha, beta, and gamma rays or neutrons, for the purpose of measurement.       The term ionizing radiation refers to those… …   Universalium

  • Level of measurement — The levels of measurement , or scales of measure are expressions that typically refer to the theory of scale types developed by the psychologist Stanley Smith Stevens. Stevens proposed his theory in a 1946 Science article titled On the theory of… …   Wikipedia

Share the article and excerpts

Direct link
… Do a right-click on the link above
and select “Copy Link”