Digital differential analyzer

This article is about the digital implementation of a Differential Analyzer. For other uses of DDA, see DDA. For the graphics algorithm, see Digital Differential Analyzer (graphics algorithm).

A digital differential analyzer (DDA), also sometimes called a digital integrating computer,^[1] is a digital implementation of a differential analyzer. The integrators in a DDA are implemented as accumulators, with the numeric result converted back to a pulse rate by the overflow of the accumulator.

The primary advantages of a DDA over the conventional analog differential analyzer are greater precision of the results and the lack of drift/noise/slip/lash in the calculations. The precision is only limited by register size and the resulting accumulated rounding/truncation errors of repeated addition. Digital electronics inherently lacks the temperature sensitive drift and noise level issues of analog electronics and the slippage and "lash" issues of mechanical analog systems.

For problems that can be expressed as differential equations, a DDA can solve them much faster than a general purpose computer (using similar technology). However reprogramming a DDA to solve a different problem (or fix a bug) is much harder than reprogramming a general purpose computer. Many DDAs were hardwired for one problem only and could not be reprogrammed without redesigning them.

History

One of the inspirations for ENIAC was the mechanical analog Bush differential analyzer. It influenced both the architecture and programming method chosen. However, although ENIAC as originally configured, could have been programmed as a DDA (the "numerical integrator" in Electronic Numerical Integrator And Calculator),^[2] there is no evidence that it ever actually was. The theory of DDAs was not developed until 1949, one year after ENIAC had been reconfigured as a stored program computer.^{[citation needed]}

The first DDA built was the Magnetic Drum Digital Differential Analyzer of 1950.

Theory

Block diagram of a basic DDA integrator

The basic DDA integrator, shown in the figure, implements numerical rectangular integration via the following equations:

$y^* = y \pm \sum \Delta y$

$S^* = S \pm y^* \sum \Delta x$

Where Δx causes y to be added to (or subtracted from) S, Δy causes y to be incremented (or decremented), and ΔS is caused by an overflow (or underflow) of the S accumulator. Both registers and the three Δ signals are signed values. Initial conditions for the problem can be loaded into both y and S prior to beginning integration.

This produces an integrator approximating the following equation:

$\Delta S = K \int \Delta y \Delta x$

where K is a scaling constant determined by the precision (size) of the registers as follows:

$K = {1 \over {\text{radix}}^n}$

where radix is the numeric base used (typically 2) in the registers and n is the number of places in the registers.

If Δy is eliminated, making y a constant, then the DDA integrator reduces to a device called a rate multiplier, where the pulse rate ΔS is proportional to the product of y and Δx by the following equation:

ΔS = KyΔx

Error sources

There are two sources of error that limit the accuracy of DDAs:^[3]

• Rounding/truncation errors due to the limited precision of the registers.
• Approximation errors due to the selection of numerical integration algorithm.

Both of these error sources are cumulative, due to the repeated addition nature of DDAs. Therefore longer problem time results in larger inaccuracy of the resulting solution.

The effect of rounding/truncation errors can be reduced by using larger registers. However, as this reduces the scaling constant K, it also increases problem time and therefore may not significantly improve accuracy and in real time DDA based systems may be unacceptable.

The effect of approximation errors can be reduced by using a more accurate numerical integration algorithm than rectangular integration (e.g., trapezoidal integration) in the DDA integrators.

Patents

• U.S. Patent 3,313,925
• U.S. Patent 3,564,223
• U.S. Patent 3,598,974

References

1. ^ Mayorov, F. V. (1964). ELECTRONIC DIGITAL INTEGRATING COMPUTERS Digital Differential Analyzers. London: Iliffe Books Ltd.. 
2. ^ Information Connection: Eniac, the first computer
3. ^ These error sources are not unique to DDAs, they also occur in programs on general purpose computers that implement numerical integration.

External links

• MADDIDA (Magnetic Drum Digital Differential Analyzer)