Distance-vector routing protocol

Distance-vector routing protocol

In computer communication theory relating to packet-switched networks, a distance-vector routing protocol is one of the two major classes of routing protocols, the other major class being the link-state protocol. Distance-vector routing protocols use the Bellman-Ford algorithm, Ford–Fulkerson algorithm, or DUAL FSM (in the case of Cisco Systems's protocols) to calculate paths.

A distance-vector routing protocol requires that a router informs its neighbors of topology changes periodically. Compared to link-state protocols, which require a router to inform all the nodes in a network of topology changes, distance-vector routing protocols have less computational complexity and message overhead.[citation needed]

The term distance vector refers to the fact that the protocol manipulates vectors (arrays) of distances to other nodes in the network.

Routers using distance vector protocol do not have knowledge of the entire path to a destination. Instead DV uses two methods:

  1. Direction in which or interface to which a packet should be forwarded.
  2. Distance from its destination.

Examples of distance-vector routing protocols include RIPv1 and RIPv2 and IGRP. EGP and BGP are not pure distance-vector routing protocols because a distance-vector protocol calculates routes based only on link costs whereas in BGP, for example, the local route preference value takes priority over the link cost.

Contents

Method

The methods used to calculate the best path for a network are different between different routing protocols but the fundamental features of distance-vector algorithms are the same across all DV based protocols.

Distance Vector means that Routers are advertised as vector of distance and Direction. Direction is simply next hop address and exit interface and Distance means hop count.

Routers using distance vector protocol do not have knowledge of the entire path to a destination. Instead DV uses two methods:

  1. Direction in which router or exit interface a packet should be forwarded.
  2. Distance from its destination.

As the name suggests the DV protocol is based on calculating the direction and distance to any link in a network. The cost of reaching a destination is calculated using various route metrics. RIP uses the hop count of the destination whereas IGRP takes into account other information such as node delay and available bandwidth.

Updates are performed periodically in a distance-vector protocol where all or part of a router's routing table is sent to all its neighbors that are configured to use the same distance-vector routing protocol. RIP supports cross-platform distance vector routing whereas IGRP is a Cisco Systems proprietary distance vector routing protocol. Once a router has this information it is able to amend its own routing table to reflect the changes and then inform its neighbors of the changes. This process has been described as ‘routing by rumor’ because routers are relying on the information they receive from other routers and cannot determine if the information is actually valid and true. There are a number of features which can be used to help with instability and inaccurate routing information.

Limitations

Count-to-infinity problem

The Bellman-Ford algorithm does not prevent routing loops from happening and suffers from the count-to-infinity problem. The core of the count-to-infinity problem is that if A tells B that it has a path somewhere, there is no way for B to know if the path has B as a part of it. To see the problem clearly, imagine a subnet connected like as A-B-C-D-E-F, and let the metric between the routers be "number of jumps". Now suppose that A is taken offline. In the vector-update-process B notices that the route to A, which was distance 1, is down - B does not receive the vector update from A. The problem is, B also gets an update from C, and C is still not aware of the fact that A is down - so it tells B that A is only two jumps from C (C to B to A) , which is false. This slowly propagates through the network until it reaches infinity (in which case the algorithm corrects itself, due to the "Relax property" of Bellman-Ford).

Workarounds and solutions

RIP uses the Split Horizon with Poison Reverse technique to reduce the chance of forming loops and uses a maximum number of hops to counter the 'count-to-infinity' problem. These measures avoid the formation of routing loops in some, but not all, cases. The addition of a hold time (refusing route updates for a few minutes after a route retraction) avoids loop formation in virtually all cases, but causes a significant increase in convergence times.

More recently, a number of loop-free distance vector protocols have been developed — notable examples are EIGRP, DSDV and Babel. These avoid loop formation in all cases, but suffer from increased complexity, and their deployment has been slowed down by the success of link-state routing protocols such as OSPF.

Example

In this network we have 4 routers A, B, C, and D: Networkabcd.svg

We shall mark the current time (or iteration) in the algorithm with T, and shall begin (at time 0, or T=0) by creating distance matrices for each router to its immediate neighbors. As we build the routing tables below, the shortest path is highlighted with the color green, a new shortest path is highlighted with the color yellow.

T=0
from A via A via B via C via D
to A
to B 3
to C 23
to D
from B via A via B via C via D
to A 3
to B
to C 2
to D
from C via A via B via C via D
to A 23
to B 2
to C
to D 5
from D via A via B via C via D
to A
to B
to C 5
to D
At this point, all the routers (A,B,C,D) have new "shortest-paths" for their DV (the list of distances that are from them to another router via a neighbor). They each broadcast this new DV to all their neighbors: A to B and C, B to C and A, C to A, B, and D, and D to C. As each of these neighbors receives this information, they now recalculate the shortest path using it.

For example: A receives a DV from C that tells A there is a path via C to D, with a distance (or cost) of 5. Since the current "shortest-path" to C is 23, then A knows it has a path to D that costs 23+5=28. As there are no other shorter paths that A knows about, it puts this as its current estimate for the shortest-path from itself (A) to D, via C.
T=1
from A via A via B via C via D
to A
to B 3 25
to C 5 23
to D 28
from B via A via B via C via D
to A 3 25
to B
to C 26 2
to D 7
from C via A via B via C via D
to A 23 5
to B 26 2
to C
to D 5
from D via A via B via C via D
to A 28
to B 7
to C 5
to D
Again, all the routers have gained in the last iteration (at T=1) new "shortest-paths", so they all broadcast their DVs to their neighbors; This prompts each neighbor to re-calculate their shortest distances again.

For instance: A receives a DV from B that tells A there is a path via B to D, with a distance (or cost) of 7. Since the current "shortest-path" to B is 3, then A knows it has a path to D that costs 7+3=10. This path to D of length 10 (via B) is shorter than the existing "shortest-path" to D of length 28 (via C), so it becomes the new "shortest-path" to D.
T=2
from A via A via B via C via D
to A
to B 3 25
to C 5 23
to D 10 28
from B via A via B via C via D
to A 3 25
to B
to C 26 2
to D 31 7
from C via A via B via C via D
to A 23 5 33
to B 26 2 12
to C
to D 33 9 5
from D via A via B via C via D
to A 10
to B 7
to C 5
to D
This time, only routers A and D have new shortest-paths for their DVs. So they broadcast their new DVs to their neighbors: A broadcasts to B and C, and D broadcasts to C. This causes each of the neighbors receiving the new DVs to re-calculate their shortest paths. However, since the information from the DVs doesn't yield any shorter paths than they already have in their routing tables, then there are no changes to the routing tables.
T=3
from A via A via B via C via D
to A
to B 3 25
to C 5 23
to D 10 28
from B via A via B via C via D
to A 3 7
to B
to C 8 2
to D 31 7
from C via A via B via C via D
to A 23 5 15
to B 26 2 12
to C
to D 33 9 5
from D via A via B via C via D
to A 10
to B 7
to C 5
to D
None of the routers have any new shortest-paths to broadcast. Therefore, none of the routers receive any new information that might change their routing tables. So the algorithm comes to a stop.

References

Further reading

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Ad hoc On-Demand Distance Vector Routing — Ad hoc On Demand Distance Vector (AODV) Routing is a routing protocol for mobile ad hoc networks (MANETs) and other wireless ad hoc networks. It is jointly developed in Nokia Research Center of University of California, Santa Barbara and… …   Wikipedia

  • Destination-Sequenced Distance Vector routing — (DSDV) is a table driven routing scheme for ad hoc mobile networks based on the Bellman Ford algorithm. It was developed by C. Perkins and P.Bhagwat in 1994. The main contribution of the algorithm was to solve the routing loop problem. Each entry …   Wikipedia

  • Routing protocol — A routing protocol is a protocol that specifies how routers communicate with each other to disseminate information that allows them to select routes between any two nodes on a network. Typically, each router has a prior knowledge only of its… …   Wikipedia

  • Link-state routing protocol — A link state routing protocol is one of the two main classes of routing protocols used in packet switched networks for computer communications. Examples of link state routing protocols include OSPF and IS IS.The link state protocol is performed… …   Wikipedia

  • Interior Gateway Routing Protocol — (IGRP) is a kind of IGP which is a distance vector routing protocol invented by Cisco, used by routers to exchange routing data within an autonomous system.IGRP is a proprietary protocol. IGRP was created in part to overcome the limitations of… …   Wikipedia

  • Interior Gateway Routing Protocol —    Abbreviated IGRP. A distance vector routing protocol from Cisco Systems for use in large heterogeneous networks.    See also heterogeneous network …   Dictionary of networking

  • Enhanced Interior Gateway Routing Protocol — (EIGRP) is a Cisco proprietary routing protocol loosely based on their original IGRP. EIGRP is an advanced distance vector routing protocol, with optimizations to minimize both the routing instability incurred after topology changes, as well as… …   Wikipedia

  • Wireless Routing Protocol — The Wireless Routing Protocol (WRP) [Citation last1 = Murthy | first1 = Shree author1 link = last2 = Garcia Luna Aceves | first2 = J. J. author2 link = title = An efficient routing protocol for wireless networks journal = Mobile Networks and… …   Wikipedia

  • Distance Vector Multicast Routing Protocol — Saltar a navegación, búsqueda Distance Vector Multicast Routing Protocol, abreviado comúnmente por sus siglas DVMRP, es un protocolo de ruteo multicast. Funcionamiento Resumidamente el protocolo funciona de la siguiente manera: Cuando un router… …   Wikipedia Español

  • Distance Vector Multicast Routing Protocol — (DVMRP Протокол дистанционно векторной многоадресной маршрутизации)  протокол маршрутизации групповых дейтаграмм для IP сетей. Протокол предназначен для использования внутри автономных систем, то есть является протоколом внутридоменной… …   Википедия

Share the article and excerpts

Direct link
… Do a right-click on the link above
and select “Copy Link”