Electrodeionization (EDI) is a water treatment process that removes ionizable species from liquids using electrically active media and an electrical potential to effect ion transport. It differs from other water purification technologies such as conventional ion exchange in that it is does not require the use of chemicals such as acid and caustic. EDI is commonly used as a polishing process to further deionize Reverse Osmosis (RO) permeate to multi-megohm-cm quality water.

The continuous electrodeionization (EDI) process, is distinguished from other electrochemical collection/discharge processes such as electrochemical ion exchange (EIX) or capacitive deionization (CapDI), in that EDI performance is determined by the ionic transport properties of the active media, not the ionic capacity of the media. EDI devices typically contain semi-permeable ion-exchange membranes and permanently charged media such as ion-exchange resin. The EDI process is essentially a hybrid of two well-known separation processes - ion exchange deionization and electrodialysis, and is sometimes referred to as filled-cell electrodialysis.

Development History

EDI theory and practice have been advanced by a large number of researchers throughout the world. It is believed that EDI was first described in a publication by scientists at Argonne Labs in January 1955 as a method for removal of trace radioactive materials from water (Walters, et al.). One of the earliest known patents describing a EDI device and process was awarded in 1957 (Kollsman). It is thought that the first pilot device incorporating mixed resins was developed by Permutit Company in the United Kingdom in the late 1950’s for the Harwell Atomic Energy Authority, as described in a paper (Gittens and Watts) and in more than one patent (Kressman; Tye). One of the first detailed theoretical discussions of EDI was written in December 1959 (Glueckauf). In April 1971, a Czechoslovakian researcher reported results of his experimental and theoretical work that advanced the theory of ionic transport within a EDI device (Matejka). The use of electroactive materials (resins) in the concentrate streams for pH control and scale prevention was proposed in 1984 (O'Hare). Layered bed devices were described in the patent literature in the early 1980’s (Kunz).

EDI devices and systems were first fully commercialized in early 1987 by a division of Millipore that is now part of Siemens Water Technologies (Ganzi et al., 1987). Since then, the theory and practice of EDI has advanced worldwide, and commercial EDI devices are now manufactured by a number of companies (Towe et al.; Parsi et al.; Rychen et al., Stewart and Darbouret). There are now thousands of EDI systems in commercial operation for the production of high purity water at capacities ranging from less than 0.01 to more than 1500 m3/h. This includes EDI systems that have been in continuous operation for over 15 years, producing makeup water for high pressure boilers (Layton).

How It Works

The electrically active media in EDI devices may function to alternately collect and discharge ionizable species, or to facilitate the transport of ions continuously by ionic or electronic substitution mechanisms. EDI devices may comprise media of permanent or temporary charge, and may be operated batchwise, intermittently, or continuously.

There are two distinct operating regimes for EDI devices: enhanced transfer and electroregeneration (Ganzi, 1988). In the enhanced transfer regime, the resins within the device remain in the salt forms. In low conductivity solutions the ion exchange resin is orders of magnitude more conductive than the solution, and act as a medium for transport of ions across the compartments to the surface of the ion exchange membranes. This mode of ion removal is only applicable in devices that allow simultaneous removal of both anions and cations, in order to maintain electroneutrality.

The second operating regime for EDI devices is known as the electroregeneration regime. This regime is characterised by the continuous regeneration of resins by electrically produced hydrogen and hydroxide ions. The dissociation of water preferentially occurs at bipolar interfaces in the ion-depleting compartment where localized conditions of low solute concentrations are most likely to occur (Simons). The two primary types of interfaces in EDI devices are resin/resin and resin/membrane. The optimum location for water splitting depends on the configuration of the resin filler. For mixed-bed devices water splitting at both types of interface can result in effective resin regeneration, while in layered bed devices water is dissociated primarily at the resin/membrane interface (Ganzi et al., 1997).

"Regenerating" the resins to their H+ and OH- forms allows EDI devices to remove weakly ionized compounds such as carbonic and silicic acids, and to remove weakly ionized organic compounds. This mode of ion removal occurs in all EDI devices that produce ultrapure water.

Under Direct Current (DC) electrical potential, Water (H2O) behaves as follows:

H2O -> H+ + OH-

Technology Overview

A typical EDI device contains alternating semipermeable anion and cation ion-exchange membranes. The spaces between the membranes are configured to create liquid flow compartments with inlets and outlets. A transverse DC electrical field is applied by an external power source using electrodes at the ends of the membranes and compartments.

When the compartments are subjected to an electric field, ions in the liquid are attracted to their respective counterelectrodes. The result is that the compartments bounded by the anion membrane facing the anode and the cation membrane facing the cathode become depleted of ions and are thus called purifying (or sometimes, diluting) compartments. The compartments bounded by the anion membrane facing the cathode and cation membrane facing the anode will then “trap” ions that have transferred in from the purifying compartments. Since the concentration of ions in these compartments increases relative to the feed, they are called concentrating compartments, and the water flowing through them is referred to as the concentrate stream (or sometimes, the reject stream).

In an EDI device, the space within the ion depleting compartments (and in some cases in the ion concentrating compartments) is filled with electrically active media such as ion exchange resin. The ion-exchange resin enhances the transport of ions and can also participate as a substrate for electrochemical reactions, such as splitting of water into hydrogen (H+) and hydroxyl (OH-) ions. Different media configurations are possible, such as intimately mixed anion and cation exchange resins (mixed bed or MB) or separate sections of ion-exchange resin, each section substantially comprised of resins of the same polarity: e.g., either anion or cation resin.

Effects on pH

pH is a measure of the acidity or alkalinity of a solution. Aqueous solutions at 25°C with a pH less than seven are considered acidic, while those with a pH greater than seven are considered basic (alkaline). When a pH level is 7.0, it is defined as 'neutral' at 25°C because at this pH the concentration of H3O+ equals the concentration of OH− in pure water. pH is formally dependent upon the activity of hydronium ions (H3O+),(H+ is often used as a synonym for H3O+.)

Effect on Oxidation Reduction Potential

Oxidation Reduction Potential (ORP) quantifies the potential for all chemical reactions in which atoms have their oxidation number (oxidation state) changed via a redox (oxidation/reduction) reaction.

This can be either a simple redox process such as the oxidation of carbon to yield carbon dioxide, or the reduction of carbon by hydrogen to yield methane (CH4), or it can be a complex process such as the oxidation of sugar in the human body through a series of very complex electron transfer processes.

The term redox comes from the two concepts of reduction and oxidation. It can be explained in simple terms:

Oxidation describes the loss of electrons by a molecule, atom or ion Reduction describes the gain of electrons by a molecule, atom or ion

However, these descriptions (though sufficient for many purposes) are not truly correct. Oxidation and reduction properly refer to a change in oxidation number—the actual transfer of electrons may never occur. Thus, oxidation is better defined as an increase in oxidation number, and reduction as a decrease in oxidation number. In practice, the transfer of electrons will always cause a change in oxidation number, but there are many reactions which are classed as "redox" even though no electron transfer occurs (such as those involving covalent bonds).

Comparing New and Old Technology

When compared with conventional resin-based, chemically regenerated deionization equipment, EDI systems offer a variety of benefits. Most obvious is the elimination of the regeneration process and its associated hazardous regeneration chemicals - acid and caustic. Since EDI operates through a combination of ion-transfer across the resins and membranes, as well as electrochemical regeneration of a portion of the bed, the resins and membranes are always functional as long as the DC voltage is applied. The resin in a conventional deionizer only purifies water when in its active (regenerated) form. As a result, the EDI system product water quality stays constant over time, whereas in regenerable deionization, product water quality degrades as the resins approach exhaustion. For those processes requiring DI water on a continuous basis, conventional systems must be duplexed so that one system can provide water while the other is regenerated. Duplexing adds cost, complexity, and size to conventional DI systems. Because EDI is continuous, and not a batch process, duplexing is not necessary. As a result of this, as well as the avoidance of regenerant chemical storage and transfer equipment, EDI system footprints are often one half of the size of their conventional counterparts.

There are significant tangible cost benefits associated with the elimination of regeneration. The costs of regeneration labor and chemicals are replaced with a small amount of electrical consumption. A typical EDI system will use approximately 1 kW-hr of electricity to deionize 1000 gallons from a feed conductivity of 50 microsiemen /cm to 0.1 µS/cm product conductivity. Since the EDI concentrate (or reject) stream contains only the feed water contaminants at 5-20 times higher concentration, it can usually be discharged without treatment, or used for another process. Thus facility costs can also be reduced since waste neutralisation equipment and ventilation for hazardous fumes are not necessary.

There are also less tangible cost reductions, which are harder to quantify, but usually favor the use of EDI systems. By eliminating hazardous chemicals wherever possible, workplace health and safety conditions can be improved. With today's increasing regulatory influence on the workplace, the storage, use, neutralisation, and disposal of hazardous chemicals result in hidden costs associated with monitoring and paperwork to conform to EPA and OSHA requirements as well as the "Right To Know" laws. In addition, the fumes, particularly from acid, often cause corrosive structural damage to facilities and equipment.

For the most part the elimination of regenerant chemicals is considered advantageous, but the chemicals do offer at least one benefit. In conventional demineralisers, acid and caustic is typically applied to the ion exchange resins at concentrations of 2-8% by weight. At these concentrations the chemicals not only regenerate the resins but clean them as well. The electrochemical regeneration that occurs in a EDI device does not provide the same level of resin cleaning. Therefore proper pretreatment is even more important with a EDI device, in order to prevent fouling or scaling. This is one of the reasons that RO pretreatment is normally required upstream of a EDI system. In general the feed water requirements for EDI systems are stricter than for a chemically regenerated demineraliser.


* [http://www.ionpure.com/ Ionpure Technologies] , Siemens Water Technologies - Ionpure Products
* [http://www.cediuniversity.com/ CEDI University web site] Online Center of Electrodeionization
* [http://www.snowpure.com/ Electropure EDI] , SnowPure, High Technology Water - Electropure EDI Products
* [http://www.dow.com/liquidseps/prod/edi_index.htm Electrodeionization (EDI)] , The Dow Chemical Company
* [http://www.anl.gov/techtransfer/docs/EDI.doc Advanced Electrodeionization Technology for Product Desalting] , Argonne National Laboratory

Papers and Publications

*ASTM Method D6807-02, “Standard Test Method for Operating Performance of Continuous Electrodeionization Systems on Reverse Osmosis Permeates from2 to 100 µS/cm”, Volume 11.02, May 2003.
*Barber .H., Towe, G. and Tessier, D. F., “EDI Operation for Removal of Weakly Ionized Impurities, International Water Conference, 2000.
*Bernatowicz, J. M., Snow, M. J. and O’Hare, R. J., “Methods and Apparatus for the Formation of Heterogeneous Ion Exchange Membranes”, U.S. Patent 6,503,957B1, January 7, 2003.
*Gallagher, C.J., Wilkins, F. C. and Ganzi, G. C., “Polarity Reversal and Double Reversal Electrodeionization Apparatus and Method”, U. S. Patent 5,558,753, September 24, 1996.
*Ganzi, G. C., “Electrodeionization for high-purity water production” AIChE Symposium Series, No. 261, Vol. 84, New Membrane Materials and Processes for Separation, edited by Sirkar, K. K. and Lloyd, pp. 73-83, 1988.
*Ganzi, G. C., “The IonpureTM continuous deionization process: Effect of electrical current distribution on performance”, Presented at the 80th annual AIChE meeting, Washington, D.C., November 28, 1988a.
*Ganzi, G. C., Egozy, Y., Giuffrida, A. J. and Jha, A., “High Purity Water by Electro-deionization” Ultrapure Water Journal, Vol. 4, No. 3, April, 1987.
*Ganzi, G. C., Jha, A., DiMascio, F. and Wood, J “The Theory and Practice of Continuous Electrodeionization,” Ultrapure Water Journal, Vol. 14, No. 6, July/August 1997.
*Gifford, J and Atnoor, D. “An Innovative Approach to Continuous Electrodeionization Module and System Design for Power Applications” International Water Conference, 2000.
*Gittens, G. J. and Watts, R. E., “Some Experimental Studies of Electrodeionisation Through Resin Packed Beds”, United Kingdom Atomic Energy Authority Research Report, 1964.
*Bjerketvedt, D., Bakke, J. R., and van Wingerden, K., “Combustion Properties of Fuel-Air Mixtures”, Chapter 4 in Gas Explosion Handbook, CMR.
*Giuffrida, A., “Heterogeneous Ion Exchange Materials Comprising Polyethylene of Linear Low Density or High Density High Molecular Weight”, U.S. Patent 5,346,924, September 13, 1994.
*Giuffrida, A., Jha, A. and Ganzi, G., “Electrodeionization Apparatus”, U.S. Patent No. 4,632,745, December 30, 1986.
*Glueckauf, E., “Electro-deionisation Through a Packed Bed”, British Chemical Engineering, December 1959, pp. 646-651.
*Griffin, C., “Advancements in the Use of Continuous Deionization in the Production of High Purity Water”, Ultrapure Water Journal, November 1991, Vol. 8, No. 8, pp 52-60.
*Gunderson, Roald, Breathing in Buildings: Indoor Air Pollution; The Problems and Solutions, http://www.mwt.net/~roald/indoorair.html, 13-Jul-99.
*Helfferich, F., “Ion-exchanger Membranes”, in Ion Exchange, Dover Publications, pp 339-420, 1995.
*Kedem, O., Schechtmann, L., Mirsky, Y., Saveliev, G. and Daltrophe, N., “Low-polarisation electrodialysis membranes” Water Supply, Vol. 17, No. 1, 305-314, 1999.
*Kollsman, P., “Method and Apparatus for Treating Ionic Fluids by Dialysis”, U.S. Patent No. 2,815,320, December 3, 1957.
*Kressman T.R.E., “Process for the Removal of Dissolved Solids from Liquids, U. S. Patent 2,923,674, February 2, 1960.
*Kunin, R., “Permselective Membranes and Their Applications” in Ion Exchange Resins, Robert Kreiger Publishing, 1990.
*Kunz G., “Process and Apparatus for Treatment of Fluids, Particularly Desalinization of Aqueous Solutions”, U.S. Patent No. 4,636,296, January 13, 1987.
*Leyton, K., Pacek, M. and Fournier, C., “Upgrading Boiler Makeup Feed Water Quality While Reducing Production Costs at the Dave Johnston Plant”, International Water Conference, November 1994.
*Mason, E. A. and Kirkham, T. A., “Design of Electrodialysis Equipment, Chemical Engineering Progress Symposium Series, No. 24, Vol. 55, 1959.
*Matejka, Z., “Continuous Production of High-Purity Water by Electro-deionization”, J. Appl. Chem. Biotechnol., 1971, Vol. 21, April.
*Neumeister H., Furst, L., Flucht, R., and Nguyen, V. D., “High Purity Water by Electrochemical Treatment”, Ultrapure Water Journal, Vol. 13, No. 7, October 1996.
*O'Hare, H. M., "Method and Apparatus for the Purification of Water", U.S. Patent No. 4,465,573, August 14, 1984.
*Oren Y., Giuffrida A. and Ciaccio S., “Process for Purifying Water”, U.S. Patent No. 5,154,809, October 13, 1992.
*Parsi, E. J., Sims, K. J., Elyanow, I. D., and Prato, T. A., “Introducing and Removing Ion-Exchange and Other Particulates from an Electrodeionization Stack”, U. S. Patent 5,066,375, November 19, 1991.
*Pittner, G. A., “Reverse Osmosis System”, U. S. Patent 4,574,049, March 4, 1986.
*Rychen, P., Alonso, S., Alt, H. and Gensbittel, D., “Apparatus for Continuous Electrochemical Desalination of Aqueous Solutions”, U. S. Patent 5,376,253, December 27, 1994.
*Schweitzer, P. A., “Electrodialysis and Dialysis” in Handbook of Separation Techniques for Chemical Engineers, McGraw Hill, pp 454-465.
*Simons, R., “Electric field effects on proton transfer between ionisable groups and water in ion exchange membranes”, Electrochimica Acta, 29(2), pp 151-158, 1984.
*Stewart, B. M. and Darbouret, D., “Advancements in the production of ultrapure water for ICP-MS analysis”, American Laboratory, April 1998, pp. 36-38.
*Thate, S., “A comparison of Different EDI Concepts Used for the Production of High Purity Water”, Ultrapure Water Journal, October 1999.
*Towe, I. G., Tessier, D. F. and Huehnergarrd, M. P., “Modular Apparatus for Demineralization of Liquids”, U.S. Patent 6,193,869B1, February 27, 2001.
*Tye, F. L., U. K. Patent 815,154, 1959.
*Walters W. R., Weiser, D. W. and Marek, L. J., “Concentration of Aqueous Radioactive Wastes” Industrial & Engineering Chemistry, Vol. 47, Jan 1955, pp. 61-67.
*White, J. L., “Electrodeionization and Ultraviolet Light Treatment Method for Purifying Water”, U. S. Patent 5,116,509, May 26, 1992.
*Wood, J.H., Ganzi, G.C., and Springthorpe, P. “Continuous Electrodeionization: Module Design Considerations for the Production of High Purity Water”

ee also


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Purified water — Bottle for Distilled water in the Real Farmacia in Madrid Purified water is water from any source that is physically processed to remove impurities. Distilled water and deionized (DI) water have been the most common forms of purified water, but… …   Wikipedia

  • EDI — may refer to:* Efficient Drivetrains Inc. * Electronic Data Interchange, a particular set of standards for computer to computer exchange of information * EDI, Extended Destination Index (a register in the x86 microprocessor architecture) *… …   Wikipedia

  • Water purification — This article is about large scale, municipal water purification. For portable/emergency water purification, see portable water purification. For industrial water purification, see deionized water. For distilled water, see distilled water. Water… …   Wikipedia

  • Fouling — This article is about fouling in engineering. For uses of the term foul outside technology, see Foul (disambiguation). Not to be confused with fowling. Heat exchanger in a steam power plant, fouled by macro fouling …   Wikipedia

  • Electrodialysis — ) in that dissolved species are moved away from the feed stream rather than the reverse. Because the quantity of dissolved species in the feed stream is far less than that of the fluid, electrodialysis offers the practical advantage of much… …   Wikipedia

  • List of waste water treatment technologies — The following page consist of a list of waste water treatment technologies: * Activated sludge systems [ [http://www.oost vlaanderen.be/docs/nl/gc/35447.%20afvalwaterzuivering%20op%20landbouwbedrijven.pdf Overview of activated sludge system with… …   Wikipedia

  • Zdeněk Matějka — Infobox Scientist name = Zdeněk Matějka image width = 225px caption = birth date = April 30, 1930 birth place = Teplice, Czechoslovakia death date = death date and age|2006|10|2|1930|4|30 death place = Prague, Czech Republic field = chemistry… …   Wikipedia

  • Reverse osmosis — Schematics of a reverse osmosis system (desalination) using a pressure exchanger. 1: Sea water inflow, 2: Fresh water …   Wikipedia

  • технология очистки воды методом электродеионизации — — [А.С.Гольдберг. Англо русский энергетический словарь. 2006 г.] Тематики энергетика в целом EN electrodeionization water purification technology …   Справочник технического переводчика

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”