- Fractional factorial design
In
statistics , fractional factorial designs areexperimental design s consisting of a carefully chosen subset (fraction) of the experimental runs of a fullfactorial design . The subset is chosen so as to exploit thesparsity-of-effects principle to expose information about the most important features of the problem studied, while using a fraction of the effort of a fullfactorial design in terms of experimental runs and resources.Notation
Fractional designs are expressed using the notation lk − p, where "l" is the number of levels of each factor investigated, "k" is the number of factors investigated, and "p" describes the size of the fraction of the full factorial used. Formally, "p" is the number of "generators", assignments as to which effects or interactions are "confounded", "i.e.", cannot be estimated independently of each other (see below). A design with "p" such generators is a 1/(lp) fraction of the full factorial design.
For example, a 25 − 2 design is 1/4 of a two level, five factor factorial design. Rather than the 32 runs that would be required for the full 25 factorial experiment, this experiment requires only eight runs.
In practice, one rarely encounters "l" > 2 levels in fractional factorial designs, since
response surface methodology is a much more experimentally efficient way to determine the relationship between the experimental response and factors at multiple levels. In addition, the methodology to generate such designs for more than two levels is much more cumbersome.The levels of a factor are commonly coded as +1 for the higher level, and -1 for the lower level. For a three-level factor, the intermediate value is coded as 0.
Generation
In practice, experimenters typically rely on statistical reference books to supply the "standard" fractional factorial designs, consisting of the "principal fraction". The "principal fraction" is the set of treatment combinations for which the generators evaluate to + under the treatment combination algebra. However, in some situations, the experimenter may take it upon himself or herself to generate his own fractional design.
A fractional factorial experiment is generated from a full factorial experiment by choosing an "alias structure". The alias structure determines which effects are confounded with each other. For example, the five factor 25 − 2 can be generated by using a full three factor factorial experiment involving three factors (say "A"," B", and "C") and then choosing to confound the two remaining factors "D" and "E" with interactions generated by "D" = "A"*"B" and "E" = "A"*"C". These two expression are called the "generators" of the design. So for example, when the experiment is run and the experimenter estimates the effects for factor "D", what is really being estimated is a combination of the main effect of "D" and the two-factor interaction involving "A" and "B".
An important characteristic of a fractional design is the defining relation, which gives the set of interaction columns equal in the design matrix to a column of plus signs, denoted by "I". For the above example, since "D" = "AB" and "E" = "AC", then "ABD" and "ACE" are both columns of plus signs, and consequently so is "BDCE". In this case the defining relation of the fractional design is "I" = "ABD" = "ACE" = "BCDE". The defining relation allows the alias pattern of the design to be determined.
Resolution
An important property of a fractional design is its resolution or ability to separate main effects and low-order interactions from one another. Formally, the resolution of the design is the minimum word length in the defining relation excluding ("1"). The most important fractional designs are those of resolution III, IV, and V: Resolutions below III are not useful and resolutions above V are wasteful in that they can estimate very high-order interactions which rarely occur in practice. The 25 − 2 design above is resolution III since its defining relation is I = ABD = ACE = BCDE.
External links
* [http://www.itl.nist.gov/div898/handbook/pri/section3/pri334.htm Fractional Factorial Designs (National Institute of Standards and Technology)]
* [http://www.isixsigma.com/library/content/c020429a.asp Save Time With Fractional Factorial DOEs (www.sixsigma.com)]References
Wikimedia Foundation. 2010.