Coalescer

A Coalescer is a technological device performing coalescence. They are primarily used to separate emulsions into their components via various processes; operating in reverse to an emulsifier.

A coalescer can be divided into mechanical and electrostatic coalescers. Mechanical coalescers use filters or baffles to make droplets coalesce while electrostatic coalescers use DC or AC electric fields (or combinations).

Mechanical Coalescers

In the area of compressed air purification, coalescing filters are used to separate liquid water and oil from compressed air using a coalescing effect. These filters additionally remove particles. The most commonly used media in this case is Borosillicate micro-fiber.

In the Oil and Gas, Petrochemical and Oil Refining industries, Liquid-Gas coalescers are widely used to remove water and hydrocarbon liquids to <0.011 ppmw (plus particulate matter to <0.3 um in size) from natural gas to ensure natural gas quality and protect downstream equipment such as compressors, gas turbines, amine or glycol absorbers, molecular sieves, PSA's, metering stations, mercury guard beds, gas fired heaters or furnaces, heat exchangers or gas-gas purification membranes.

liquid-liquid coalescers can also be used to separate hydrocarbons from water phases such as oil removal from produced water.^[1]. They have been also used in pyrolysis gasoline (benzene) removal from quench water in ethylene plants, although in this application, the constant changing of cartridges can lead to operator exposure to BTX (Benzene, Toluene, Xylene), as well as disposal issues and high operating costs from frequent replacement.

Electrostatic Coalescers

Electrostatic coalescers use electrical fields to induce droplet coalescence in water-in-crude-oil emulsions to increasing the droplet size. The squared dependence of droplet diameter in stokes law, increase the settling speed and destabilizes the emulsion. The effects on the water droplet arise from the very different dielectric properties of the conductive water droplets dispersed in the insulating oil. Water droplets have a permittivity that is much higher than the surrounding oil. Furthermore, water with dissolved salt is also a very good conductor. When a uncharged droplet is subjected to a AC electric field the field will polarize the droplet creating a electric field around the droplet to counteract the external field. As the water droplet is very conductive the induced charges will reside on the surface. The droplet has no net charge but one positive and one negative side. Inside the droplet the electric field is zero. When two droplets with induced dipoles gets close to each other, they will experience a force pulling the droplets closer until they coalesce.

In oil production, co-produced water is mixed with the oil in choke valves and process equipment producing water-in-oil emulsions. The amount of water increases during the production life of the reservoir. The emulsions are destabilized using gravitational separators, and the settling rates are increased by applying heat, demulsifiers, and AC electric fields. The AC electric field gives rise to attractive forces between water droplets, and increases the probability of coalescence at contact. According to Stokes law, the settling rate increases proportionally with the square of the drop diameter. By promoting coalescence of small water droplets, the settling rate can be greatly increased. The water content is normally reduced to <0.5 vol% if this is the final treatment stage before the crude oil is exported.

Typical electrocoalescers are large settling tanks containing electrodes and operates under laminar-flow conditions with bare electrodes that may be vulnerable to short circuiting. An alternative to this type of coalescer is a flow through pre-coalescer that is installed upstream a separator tank. In the Compact Electrostatic Coalescer ^[2]. droplet coalescence is achieved by applying AC electric fields (50–60 Hz) to water-in-oil emulsions under turbulent-flow conditions. The turbulence increases the collision frequency between the water drops. The electrodes are insulated to prevent short circuiting, and permits water contents of up to 40% as well as water slugs. The equipment is a separate flow-through electrostatic treatment section installed upstream of a gravity separator to improve the performance. By keeping the treatment and settling sections separate, a compact electrostatic coalescer can be obtained that can also be retrofitted.^[3].

Liquid-liquid coalecers are also widely used in oil refining industry to remove the last traces of contaminants like amine or caustic from intermediate products in oil refineries, and also for the last stage dewatering of final products like kerosene (jet fuel), LPG, gasoline and diesel to <15 ppmw free water in the hydrocarbon phase. These coalescers are often electrostatic type, in which a DC electrical field encourages the water droplets to coalesce and settle by gravity.

References

1. ^ http://www.opusplus.co.uk/technology.php?pID=18 | Coalescer Equipment Vendor
2. ^ http://www.tekna.no/ikbViewer/Content/19748/Einar%20E%20Johnsen%20-%20Glitne.pdf | Compact Electrostatic Coalescer Conference Paper
3. ^ http://www.akersolutions.com/en/Global-menu/Products-and-Services/technology-segment/Wellstream-processing/Process-systems-technologies/Crude-oil/Crude-oil-separation/Compact-technologies/Compact-electrostatic-coalescer-CEC/ | Compact Electrostatic Coalescer Equipment Vendor