Successive Approximation ADC

A successive approximation ADC is a type of analog-to-digital converter that converts a continuous analog waveform into a discrete digital representation via a binary search through all possible quantization levels before finally converging upon a digital output for each conversion.

Algorithm

The successive approximation Analog to digital converter circuit typically consists of four chief subcircuits:

:# A sample and hold circuit to acquire the input voltage (V_in).:# An analog voltage comparator that compares V_in to the output of the internal DAC and outputs the result of the comparison to the successive approximation register (SAR).:# A successive approximation register subcircuit designed to supply an approximate digital code of V_in to the internal DAC.:# An internal reference DAC that supplies the comparator with an analog voltage equivalent of the digital code output of the SAR for comparison with V_in.

The successive approximation register is initialized so that the most significant bit (MSB) is equal to a digital 1. This code is fed into the DAC which then supplies the analog equivalent of this digital code (V_ref/2) into the comparator circuit for comparison with the sampled input voltage. If this analog voltage exceeds V_in the comparator causes the SAR to reset this bit and set the next bit to a digital 1. If it is lower then the bit is left a 1 and the next bit is set to 1. This binary search continues until every bit in the SAR has been tested. The resulting code is the digital approximation of the sampled input voltage and is finally output by the ADC at the end of the conversion (EOC).

Mathematically, let V_in = xV_ref, so x in [-1, 1] is the normalized input voltage. The objective is to approximately digitize x to an accuracy of 1/2ⁿ. The algorithm proceeds as follows::# Initial approximation x₀ = 0.:# ith approximation x_i = x_i-1 - s(x_{i-1 - x)/2ⁱ.
where, s(x) is the signum-function(sgn(x)) (+1 for x ≥ 0, -1 for x < 0). It follows using mathematical induction that |xn - x| ≤ 1/2ⁿ.}

As shown in the above algorithm, a SAR ADC requires::# An input voltage source V_in.:# A reference voltage source V_ref to normalize the input.:# A DAC to convert the ith approximation x_i to a voltage.:# A Comparator to perform the function s(x_i - x) by comparing the DAC's voltage with the input voltage.:# A Register to store the output of the comparator and apply x_i-1 - s(x_i-1 - x)/2ⁱ.

Charge-Redistribution Successive Approximation ADC

One of the most common implementations of the successive approximation ADC, the "charge-redistribution" successive approximation ADC, uses a charge scaling DAC. The charge scaling DAC simply consists of an array of individually switched binary-weighted capacitors. The amount of charge upon each capacitor in the array is used to perform the aforementioned binary search in conjunction with a comparator internal to the DAC and the successive approximation register.

The DAC conversion is performed in four basic steps.

:# First, the capacitor array is completely discharged to the offset voltage of the comparator, V_OS. This step provides automatic offset cancellation(i.e. The offset voltage represents nothing but dead charge which cant be juggled by the capacitors). :# Next, all of the capacitors within the array are switched to the input signal, "v"_IN. The capacitors now have a charge equal to their respective capacitance times the input voltage minus the offset voltage upon each of them. :# In the third step, the capacitors are then switched so that this charge is applied across the comparator's input, creating a comparator input voltage equal to -"v"_IN. :# Finally, the actual conversion process proceeds. First, the MSB capacitor is switched to V_REF, which corresponds to the full-scale range of the ADC. Due to the binary-weighting of the array the MSB capacitor forms a 1:1 divided between it and the rest of the array. Thus, the input voltage to the comparator is now -"v"_IN plus V_REF/2. Subsequently, if "v"_IN is greater than V_REF/2 then the comparator outputs a digital 1 as the MSB, otherwise it outputs a digital 0 as the MSB. Each capacitor is tested in the same manner until the comparator input voltage converges to the offset voltage, or at least as close as possible given the resolution of the DAC.

Split Capacitor Array

See also

* Quantization noise
* Digital-to-Analog Converter

References

* R. J. Baker, "CMOS Circuit Design, Layout, and Simulation, Revised Second Edition", Wiley-IEEE, 2008. ISBN 978-0-470-22941-5

External links

* [http://www.maxim-ic.com/appnotes.cfm/appnote_number/1080/CMP/WP-50 Understanding SAR ADCs ]