Expansion joint

Expansion joint
For the railway-specific expansion joints, see Breather switch.
Expansion joint on a bridge

An expansion joint or movement joint is an assembly designed to safely absorb the heat-induced expansion and contraction of various construction materials, to absorb vibration, to hold certain parts together, or to allow movement due to ground settlement or earthquakes. They are commonly found between sections of sidewalks, bridges, railway tracks, piping systems, ships, and other structures.

Throughout the year, building faces, concrete slabs, and pipelines will expand and contract due to the warming and cooling through seasonal variation, or due to other heat sources. Before expansion joint gaps were built into these structures, they would crack under the stress induced.

The expansion joint can be as simple as a caulked separation between two sections of the same materials. More recently, expansion joints have been included in the design of, or added to existing, brick exterior veneer walls for similar purposes. In concrete and concrete block ("CMU") construction, the term applied is control joint, but serves a similar purpose.

Contents

Road / bridge control (expansion) joints

Saw cut expansion joints in concrete.

Control joints (often confused with expansion joints) are cut into the concrete or asphalt, and are different from expansion joints as shown in the photo. The joints are cut into the structure at regular intervals allow cracking to occur in a controlled fashion. Road control joints can be sealed with hot tar, cold sealant (such as silicone), or compression sealant (such as rubber).

Pipe expansion joints

Single sphere rubber bellows expansion joint, with flanges.
Stainless steel pipe expansion joint, with control rods.

Pipe expansion joints are necessary in systems that convey high temperature commodities such as steam or exhaust gases, or to absorb movement and vibration. A typical type of expansion joint for pipe systems is a bellows which can be manufactured from metal (most commonly stainless steel), plastic (such as PTFE), fabric (such as glass fibre) or an elastomer such as rubber. A bellow is made up of a series of one or more convolutions, with the shape of the convolution designed to withstand the internal pressures of the pipe, but flexible enough to accept the axial, lateral, and/or angular deflections. Expansion joints are also designed for other criteria, such as noise absorption, anti-vibration, earthquake movement, and building settlement. Metal expansion joints have to be designed according to rules laid out by EJMA, while for fabric expansion joints only guidelines and a state-of-the-art description exists by the Quality Association for Fabric Expansion Joints.

Pipe expansion joints are also known as compensators, as they 'compensate' for the thermal movement.

Pressure Balanced Expansion Joints

Expansion joints are often included in industrial piping systems to accommodate movement due to thermal and mechanical changes in the system. When the process requires large changes in temperature, metal components change size. Expansion joints with metal bellows are designed to accommodate certain movements while minimizing the transfer of forces to sensitive components in the system.

Pressure created by pumps or gravity is used to move fluids through the piping system. Fluids under pressure occupy the volume of their container. The unique concept of pressure balanced expansion joints is they are designed to maintain a constant volume by having balancing bellows compensate for volume changes in the bellows (line bellows) which is moved by the pipe. An early name for these devices was “pressure-volumetric compensator”.[1]

Rubber expansion Joint Manufacturing

Wrapping fabric reinforced rubber sheets

Rubber expansion joint are mainly manufactured by manual wrapping of rubber sheets and fabric reinforced rubber sheets around a bellow shaped product mandrel. Besides rubber and fabric reinforced rubber sometimes also steel wires or metal rings are added for additional reinforcement. After the entire product is build up on the mandrel it is covered with a winding of (nylon) peel ply to pressurize all layers together before pressurization. Because of the labor intensive production process large part of the production has moved to eastern Europe and Asian countries.

Molded rubber expansion joints

Some types of rubber expansion joints are made with a molding process. Typical joints that are molded are medium sized expansion joints with bead rings which are produced in large quantities. These rubber expansion joints are manufactured on a cylindrical mandrel, which is wrapped with bias cut fabric ply. At the end the bead rings are positioned and the end sections are folded inwards over the bead rings. This part is finally placed in a mold and molded into shape and vulcanized. This is a highly automated solution for large quantities of the same type of joint.

Automated winding of rubber expansion joints

Lately new technology has been developed to wind rubber and reinforcement layers on the (cylindrical or bellow shaped) mandrel in an automated fashion using industrial robots instead of manual wrapping. The automated production with a robot is fast and accurate which provides a repeatable high quality. Another aspect of using industrial robots for the production of rubber expansion joints is the possibility to apply an individual reinforcement layer instead of using pre-woven fabric. The fabric reinforcement is pre-woven and cut at the preferred bias angle. With individual reinforcement it is possible to add more or less fiber material at different sections of the product by changing the fiber angles over the length of the product. [2]

Expansion joint accessories

Liners

Internal liners can be used to either protect the metallic bellows from erosion or reduce turbulence across the bellows. They must be used when purge connectors are included in the design. In order to provide enough clearance in the liner design, appropriate lateral and angular movements must be specified by the designer. When designing an expansion joint with combination ends, flow direction must be specified as well.[3]

Covers

External covers should be used to protect the internal bellows from being damaged. They also serve a purpose as insulation of the bellows. Covers can either be designed as removable or permanent accessories. [4]

Particulate barriers/purge connectors

In systems that have a media with significant particulate content (i.e. flash or catalyst), a barrier of ceramic fiber can be utilized to prevent corrosion and restricted bellows flexibility resulting from the accumulation of the particulate. Purge connectors may also be utilized to perform this same function. Internal liners must also be included in the design if the expansion joint includes purge connectors or particulate barriers.[5]

Limit rods

Limit rods may be used in an expansion joint design to limit the axial compression or expansion. They allow the expansion joint to move over a range according to where the nut stops are placed along the rods. Limit rods are used to prevent bellows over-extension while restraining the full pressure thrust of the system in the case that a main . Bellows Catalog: Limit Rod], U.S. Bellows, Inc. (retrieved 31 August 2010)

Ducted air systems

Expansion joints are required in large ducted air systems to allow fixed pieces of piping to be largely free of stress as thermal expansion occurs. Bends in elbows also can accommodate this. Expansion joints also isolate pieces of equipment such as fans from the rigid ductwork thereby reducing vibration to the ductwork as well as allowing the fan to “grow” as it comes up to the operating air system temperature without putting stress on the fan or the fixed portions of ductwork.

An expansion joint is designed to allow deflection in the axial (compressive), lateral (shear), or angular (bending) deflections. Expansion joints can be non-metallic or metallic (often called bellows type). Non-metallic can be a single ply of rubberized material or a composite made of multiple layers of heat and erosion resistant flexible material. Typical layers are: outer cover to act a gas seal, a corrosion resistant material such as Teflon, a layer of fiberglass to act as an insulator and to add durability, several layers of insulation to ensure that the heat transfer from the flue gas is reduced to the required temperature and an inside layer.

A bellows is made up of a series of one or more convolutions of metal to allow the axial, lateral or angular deflection required(Note: If required).

References

  1. ^ Technical Bulletin: Pressure Balanced Expansion Joints, U.S. Bellows, Inc. (retrieved 31 August 2010)
  2. ^ TANIQ: automated winding of rubber joints, TANIQ(retrieved 6 December 2010)
  3. ^ U.S. Bellows Catalog: Internal Liner, U.S. Bellows, Inc. (retrieved 31 August 2010)
  4. ^ U.S. Bellows Catalog: Protective Cover, U.S. Bellows, Inc. (retrieved 31 August 2010)
  5. ^ U.S. Bellows Catalog: Purge Connector, U.S. Bellows, Inc. (retrieved 31 August 2010)

See also

  • Breather switch
  • Expansion Joint Manufacturers Association, Inc.
  • Reinforced rubber
  • Slide plate

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Expansion joint — Expansion Ex*pan sion, n. [L. expansio: cf. F. expansion.] 1. The act of expanding or spreading out; the condition of being expanded; dilation; enlargement. [1913 Webster] 2. That which is expanded; expanse; extend surface; as, the expansion of a …   The Collaborative International Dictionary of English

  • expansion joint — noun 1. : a coupling (as of steam pipes) designed to permit an endwise movement that compensates for expansion or contraction resulting from temperature changes 2. : a joint or gap (as in concrete work) designed to permit expansion or contraction …   Useful english dictionary

  • expansion joint — a joint between two parts of a structure, machine, etc., permitting expansion, as from heat, without structural damage. [1840 50] * * * …   Universalium

  • expansion joint — noun a joint that makes allowance for thermal expansion of the parts joined without distortion …   English new terms dictionary

  • expansion joint — any device containing one or more bellows used to absorb dimensional changes, such as those caused by thermal expansion or contraction of a pipeline, duct, or vessel …   Mechanics glossary

  • expansion joint — Device in piping designed to allow movement of the pipe caused by the pipe s expansion and contraction …   Dictionary of automotive terms

  • expansion joint — noun A structural separation between two building elements that allows free movement between the elements without damage to the system …   Wiktionary

  • pressure balanced expansion joint — a pressure balanced expansion joint is designed to absorb axial movement and/or lateral deflection while restraining the pressure thrust by means of tie devices interconnecting the flow bellows with an opposed bellows also subjected to line… …   Mechanics glossary

  • hinged expansion joint — a hinged expansion joint contains one bellows and is designed to permit angular rotation in one plane only, by the use of a pair of pins through hinge plates attached to the expansion joint ends. The hinges and hinge pins must be designed to… …   Mechanics glossary

  • internally guided expansion joint — an internally guided expansion joint is designed to provide axial guiding within the expansion joint by incorporating a heavy internal guide sleeve, with or without the use of bearing rings. The use of such expansion joints will assure… …   Mechanics glossary

Share the article and excerpts

Direct link
… Do a right-click on the link above
and select “Copy Link”