Conical scanning

Conical scanning

Conical scanning is a system used in early radar units to improve their accuracy, as well as making it easier to steer the antenna properly to point at a target. Conical scanning is similar in concept to the earlier lobe switching concept used on some of the earliest radars, and many examples of lobe switching sets were modified in the field to conical scanning during World War II, notably the German Würzburg radar. With simple electronics, antenna guidance can be made entirely automatic, although potential failure modes and susceptibility to deception jamming led to the replacement of conical scan systems with monopulse radar sets.

Contents

Concept

A typical radar antenna commonly has a beam width of a few degrees. While this is adequate for locating the target in an early warning role, it is not nearly accurate enough for gun laying, which demands accuracies on the order of 0.1 degrees. It is possible to improve the beam width through the use of larger antennas, but this is often impractical.

In order to monitor the direction of a designated target, it is only necessary to keep the aerial pointing directly at the target. Knowledge of the pointing direction of the aerial then naturally gives knowledge of the target direction. In order to have the radar system follow a moving target automatically, it is necessary to have a control system that keeps the aerial beam pointing at it as it moves. The radar receiver will get maximum returned signal strength when the target is in the beam centre, So if the beam is pointed directly at the target, when the target moves it will move out of the beam center and the received signal strength will fall. Circuitry designed to monitor any fall off in received signal strength could be used to control a servo motor that steers the aerial to follow the target motion. There are three difficulties with this method:

  1. The radar will have no information as to which direction the target has moved, and therefore no indication as to which direction to move the aerial to follow it.
  2. As the target moves away from the beam centre, the received power changes only very slowly at first. Thus the system is rather insensitive to aerial pointing errors.
  3. Real variations in target echo power caused by scintillation will be interpreted as target motion.

Conical Scanning

Conical scanning concept. The radar beam is rotated in a small circle around the "boresight" axis, which is pointed at the target. The circle is small enough so the target is within the edge of the "lobe" of the radar beam and reflects a weak signal back. If the target is in the center of the circle, on the boresight axis, the reflected signal will have a constant strength as the beam rotates around it. However, if the target moves to one side of the circle the reflected signal will be stronger when the beam reaches that side of the circle, and weaker when the beam is on the other side, so the return signal strength will oscillate as the beam is rotated. For example, if the target moves up, when the beam reaches the top of its circle the target will be closer to the center of the lobe and will reflect a stronger signal than when the beam is at the bottom of its circle. From this changing return signal the direction the target has moved is electronically calculated, and the boresight axis is automatically moved to follow the target.

Conical scanning addresses this problem by "moving" the radar beam slightly off center from the antenna's midline, and then rotating it. Given an example antenna that generates a beam of 2 degrees width – fairly typical – a conical scanning radar might move the beam 1.5 degrees to one side of the centerline by offsetting the feed slightly. The resulting pattern, at any one instant in time, covers the midline of the antenna for about 0.5 degrees, and 1.5 degrees to the side. By spinning the feed horn with a motor, the pattern becomes a cone centered on the midline, extending 3 degrees to the sides in our example.

The key concept is that a target located at the midline point will generate a constant return no matter where the lobe is currently pointed, whereas if it is to one side it will generate a strong return when the lobe is pointed in that general direction and a weak one when pointing away. Additionally the portion covering the centerline is near the edge of the radar lobe, where sensitivity is falling off rapidly. An aircraft centered in the beam is in the area where even small motions will result in a noticeable change in return, growing much stronger along the direction the radar needs to move. The antenna control system is arranged to move the antenna in azimuth and elevation such that a constant return is obtained from the aircraft being tracked. Whilst use of the lobe alone might allow an operator to "hunt" for the strongest return and thus aim the antenna within a degree or so in that "maximum return" area at the center of the lobe, with conical scanning much smaller movements can be detected, and accuracies under 0.1 degree were possible.

Construction

There are two ways to cause the redirection of the beam from the antenna's midline. The first is referred to as a rotated feed. As its name suggests, a feed horn is set just off the parabolic focal point which causes the energy to focus slightly off the antenna midline. The feed is then rotated around the focal point of the paraboloid to produce the conical rotation. The other system is a nutated feed. A nutated feed offsets the antenna at an angle to a fixed feed horn, and then rotates the antenna. A variation of a nutated feed makes the feed move in a small circle, rapidly and continuously changing the pointing direction of the beam. In this latter type, neither the feed nor the antenna revolves around the pointing axis of the antenna; only the pointing direction changes, tracing out a narrow cone.

The primary difference between the two basic schemes is in polarization. As the feed horn in the rotated process spins, the polarization changes with the rotation and will thus be 90 degrees off in polarization when the feed is 90 degrees off its initial axis. As the feed horn is fixed in nutated feeds, no polarization changes occur. Most early systems used a rotated feed, due to its mechanical simplicity, but later systems often used nutated feeds in order to use the polarization information.

In the U.S. Navy Mk. 25 gun fire control radar, spiral scan mode aided target acquisition. Basically conical scan (of the non-revolving nutating feed type), the size of the scan cone cyclically increased and decreased roughly twice a second. The scanned area was several degrees, in all. (Once the target was acquired, the operator switched to conical scan for tracking.)

Since the lobe is being rotated around the midline of the antenna, conical scanning is only really appropriate for antennas with a circular cross section. This was the case for the Würzburg, which operated in the microwave region. Most other forces used much longer-wavelength radars that would require paraboloid antennas of truly enormous size, and instead used a "bedspring" arrangement of many small dipole antennas arranged in front of a passive reflector. To arrange conical scanning on such a system would require all of the dipoles to be moved, an impractical solution. For this reason the US Army simply abandoned their early gun laying radar, the SCR-268. This was not particularly annoying, given that they were in the process of introducing their own microwave radar in the aftermath of the Tizard Mission, the SCR-584.

Automatic guidance for the antenna, and thus any slaved guns or weapons, can be added to a conical scan radar without too much trouble. The control system has to steer the antenna such that a constant amplitude return is received from the target.

Unfortunately there are a number of factors that can dramatically change the reflected signal. For instance, changes in the target aircraft's direction can present different portions of the fuselage to the antenna, and dramatically change the amount of signal being returned. In these cases, a conical scan radar might interpret this change in strength as a change in position. For instance, if the aircraft were to suddenly "brighten" when it was off-axis to the left, the circuitry might interpret this as being off to the right if the change occurs when the lobe is aligned in that direction. This problem can be solved by using two simultaneous overlapping receiver beams leading to the monopulse radar, so-named because it always compares signal strength from a single pulse against itself, thereby eliminating problems with all but impossibly fast changes in signal strength.

Conical Scan Receive Only (COSRO)

COSRO systems do not modify the transmit signal sent from the antenna.

Antenna waveguide in COSRO systems includes an RF received feedhorn structure that produces a left/right RF receive sample and an up/down RF receive sample. These two signals are multiplexed inside a waveguide device that has a rotating vane. The output of the multiplex device is a single RF signal and two position signals that indicate left/right and up/down.

The COSRO technique does not transmit any signals that indicate the position of the rotating vane.

Antenna Sampling

RF receive signals from multiple transmit pulses are combined mathematically to create a vertical and horizontal signal. The vertical signal is created by adding RF samples when the vane/feedhorn is in the up direction and subtracting RF samples when the vane/feedhorn is in the down direction. The horizontal signal is created by adding RF samples when the vane/feedhorn is in the left direction and subtracting RF samples when the vane/feedhorn is in the right direction.

This produces a pair of angle error signals used to drive antenna positioning drive motors.

Jamming

Conical scan radars can be easily jammed. If the target knows the general operating parameters of the radar, it is possible to send out a false signal timed to grow and fade in the same pattern as the radar lobe, but inverted in strength. That is, the false signal is at its strongest when the radar signal is the weakest (the lobe is on the "far side" of the antenna compared to the aircraft), and weakest when the signal is the strongest (pointed at the aircraft). When added together with the "real" signal at the radar receiver, the resulting signal is "always strong", so the control system cannot make an accurate estimate as to where in the lobe pattern the target is located.

Actually accomplishing this in hardware is not as difficult as it may sound. If one knows that the signal is rotated at 25 RPM, as it was in the Würzburg radar, the jammer is built to fade from maximum to zero at the same speed, 25 times a second. Then all that is needed is to sync the signals up, which is accomplished by looking for the low point in the signal (which is generally easier to find) and triggering the pattern at that point. This system, known as inverse gain jamming, was used operationally by the Royal Air Force against the Würzburg radar during WWII.

It is possible to arrange a radar so the lobes are not being moved in the broadcaster, only the receiver. To do this, one adds a second antenna with the rotating lobe for reception only, a system known as COSRO, for Conical Scan on Receive Only (compare to LORO, a similar system used against lobe switching radars). Although this denied lobing frequency information to the jammer in the aircraft, it was still possible to simply send out random spikes and thereby confuse the tracking system (or operator). This technique, called SSW for Swept Square Wave, doesn't protect the aircraft with the same sort of effectiveness as inverse gain, but is better than nothing and often fairly effective.

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • conical scanning — A radar scan pattern in which a point on the radar beam describes a circle at the base of a cone. This type of scan pattern provides both elevation and azimuth data. The radiation pattern of the antenna is made slightly lopsided, and the antenna… …   Aviation dictionary

  • conical-scanning radar — kūginės žvalgos radaras statusas T sritis radioelektronika atitikmenys: angl. conical scanning radar vok. Radar mit konischer Abtastung, n rus. радиолокационная станция с коническим сканированием, f pranc. radar à balayage conique, m …   Radioelektronikos terminų žodynas

  • scanning — In radar, the motion of the radar antenna assembly when searching for targets. Scanning usually follows a systematic pattern involving one or more of the following: i. In horizontal scanning (or search lighting), the antenna is continuously… …   Aviation dictionary

  • Environmental scanning electron microscope — Wool fibers imaged in an ESEM by the use of two symmetrical plastic scintillating backscattered electron detectors …   Wikipedia

  • CESE — Conical scanning Earth Sensor Electronics Contributor: GSFC …   NASA Acronyms

  • Monopulse radar — is an adaptation of conical scanning radar which sends additional information in the radar signal in order to avoid problems caused by rapid changes in signal strength. The system also makes jamming more difficult. Most radars designed since the… …   Wikipedia

  • Silkworm missile — The HY 2 Haiying (zh cpl|c=海鹰|p=hǎiyīng|l=Sea Eagle), known in Western media as the Silkworm missile, is an anti ship cruise missile made by the People s Republic of China and still used by many countries in the Middle East. Since the 1980s, the… …   Wikipedia

  • Cone — This disambiguation page lists articles associated with the same title. If an internal link led you here, you may wish to change the link to point directly to the intended article …   Wikipedia

  • Lobe switching — is a method used on early radar sets to improve tracking accuracy. It used two slightly separated antenna elements to send the beam slightly to either side of the midline of the antenna, switching between the two to find which one gave the… …   Wikipedia

  • P-15 Termit — Termit A P 15M missile (SS N 2c) being unloaded from a former East German Navy Tarantul class missile boat. Type Anti ship missile …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”