Malfunction (parachuting)

A malfunction is a partial or total failure of a parachuting device to operate as intended. Malfunctions may require a skydiver to cut-away his or her main parachute and deploy the reserve parachute.

1: At about 100 m. reserve canopy suddenly unpacks and opens
2: Skydiver decides not to cutaway the main canopy, because of too low altitude. Reserve canopy goes forward and strikes the main canopy.
3: Skydiver fights for main canopy. Main and reserve canopies take position biplane (one of two possible positions when both canopies can work)
Photograph by Dmitry A. Mottl

High speed malfunctions

Pilot chute in tow

This happens with the popular throw-out deployment system where the pilot chute does not pull the pin and open the container or once opened does not exert enough force to extract the deployment bag from the container. It can be caused by pilot chutes with kill lines which have not been cocked during packing or where the kill line has shrunk through use and reduces the drag of the pilot chute. It can be caused by a mis-routed pilot chute bridle. It can also be caused by too large a deployment bag & canopy for the container, although deployment bags should be matched to the containers. The correct procedure with this malfunction is to deploy the reserve from a stable belly down position. If time permits the skydiver might first attempt to bump their container to dislodge a trapped deployment bag. If this malfunction is temporary and clears it is called a pilot chute hesitation.

Bag lock

This malfunction occurs when the deployment bag is extracted from the main container but fails to release the canopy within. The correct procedure to clear the malfunction is to cut away the main and deploy the reserve.

Horseshoe

A "horseshoe" describes a malfunction where a parachute deploys but remains attached to a skydiver by its risers and at least one other point. This prevents the canopy from opening properly, and the canopy and lines form a horseshoe shape extending from the risers up and then back down again to the other point where the parachute remains attached to or entangled with the skydiver. This malfunction may occur when the closing pin of a skydiving rig is released from the closing loop and allows the deployment bag to separate from the container. Because the pilot chute is still stowed, the malfunction takes on the shape of a horseshoe. This malfunction may also occur if the pilot chute or bridle connecting the pilot chute to the canopy becomes entangled with the skydiver. It is possible, though rare, to experience this type of malfunction when one or more parachute lines entangle with or snag on some portion of the parachute rig.

Procedures for clearing a horseshoe malfunction

The skydiver may attempt to extract the pilot chute or clear the entanglement. Extracting the pilot chute, while simple during the course of a normal skydive, becomes a new challenge because its location will have shifted due to the deployment of the main canopy. Skydivers may wish to practice on the ground deploying their pilot chute with the main canopy out of the container in order to gain experience with this procedure. If successfully cleared, the main parachute will likely fail to deploy correctly due to severe line twists. However, the skydiver can treat this as a normal high-speed malfunction, release the main, and deploy the reserve. Failing to clear the entanglement prior to deploying the reserve may result in a main-reserve entanglement. Failing to achieve either successful deployment of the main, or manual or automatic deployment of the reserve will result in a near certain death.

Slider hangup

This malfunction occurs when the slider does not descend fully, preventing the canopy from inflating completely.

If it is hung up near the top of the lines, the canopy will not provide sufficient lift or drag, and the rate of descent will be high. In this case one will need to cut away the main and deploy the reserve.

If the slider hangs up midway down the lines, the canopy will inflate almost normally (and may or may not be safe to land in that condition). In this case, the slider can be usually "worked" the rest of the way down by pulling on the rear risers, or by releasing the steering lines ("brakes") and pulling them down repeatedly ("pumping"). If the malfunction can not be cleared sufficiently and once decides to cut away, the decision to do so must be made at a high enough altitude to allow the reserve to deploy.

Low speed malfunctions

Line over

This malfunction occurs when one or more of the canopy's lines pass in front of the nose prior to inflation. This causes the canopy to open in a "Bow-tie" shape. The result is generally an uncontrollable spin. The correct procedure to clear the malfunction is to cut away although it is sometimes possible to clear the malfunction by collapsing the parachute and letting the line pass back into the right position.

Two canopies out

Since a sport skydiver jumps with a main and a reserve parachute, it is possible for both parachutes to deploy. This often occurs when a skydiver employing an AAD deploys his or her main canopy at an altitude low enough for the AAD to activate. This may result in a dangerous main-reserve entanglement. More commonly, the two canopies will arrange themselves in a biplane, side-by-side, or a dangerous downplane configuration. Having two deployed parachutes side by side can create considerably more lift to the point of becoming dangerously hard to control. One should always attempt to fly the canopy more overhead.

Line twist

This is where a parachute twists around the vertical axis on deployment. This causes the parachute to only partially open especially if the slider is above the line twists. If a skydiver is unable to kick from off the twists (rotating his body to untwist the lines) he will have to cutaway.

Twisted parachute lines immediately after deployment

Closed end cells

This is when the parachute is open, but the end cells haven't yet inflated. This can usually be cleared by just waiting, and they will self-inflate, or you can pull gently on the back risers, or, as most people recommend, releasing the brakes and pumping a couple of times.

External links

• Article on Malfunctions