Pigging

of the product in the pipeline is used to push it along down the pipe until it reaches the receiving trap - the 'pig catcher'.

If the pipeline contains butterfly valves, the pipeline cannot be pigged. Ball valves cause no problems because the inside diameter of the ball can be specified to the same as that of the pipe.

Pigging has been used for many years to clean larger diameter pipelines in the oil industry. Today, however, the use of smaller diameter pigging systems is now increasing in many continuous and batch process plants as plant operators search for increased efficiencies. [http://www.piggingsystems.com]

Pigging can be used for almost any section of the transfer process between, for example, blending, storage or filling systems. Pigging systems are already installed in industries handling products as diverse as lubricating oils, paints, chemicals, toiletries, and foodstuffs.

Pigs are used in lube oil or painting blending: they are used to clean the pipes to avoid cross-contamination, and to empty the pipes into the product tanks (or sometimes to send a component back to its tank). Usually pigging is done at the beginning and at the end of each batch, but sometimes it is done in the midst of a batch, e.g. when producing a premix that will be used as an intermediate component.

Pigs are also used in oil and gas pipelines: they are used to clean the pipes but also there are "smart pigs" used to measure things like pipe thickness along the pipeline. They usually do not interrupt production, though some product can be lost when the pig is extracted. They can also be used to separate different products in a multiproduct pipeline.

Pigging in production environments

Product and time saving

A major advantage of piggable systems is the potential resulting product savings. At the end of each product transfer, it is possible to clear out the entire line contents with the pig, either forwards towards the receipt point, or backwards to the source tank.There is no requirement for extensive line flushing.

Without the need for line flushing, pigging offers the additional advantage of a much more rapid and reliable product changeover. Product sampling at the receipt point becomes faster because the interface between products is very clear, and the old method of checking at intervals, until the product is on-specification, is considerably shortened.

Pigging Systems can also be operated totally by a Programmable Logic Controller (PLC).

Environmental issues

Pigging has a significant role to play in reducing the environmental impact of batch operations. Traditionally, the only way that an operator of a batch process could ensure a product was completely cleared from a line was to flush the line with a cleaning agent such as water or a solvent or even the next product. This cleaning agent then had to be subjected to effluent treatment or solvent recovery. If Product was used to clear the line, the contaminated finished product was downgraded or dumped. All of these problems can now be eliminated due to the very precise interface produced by modern pigging systems.

afety considerations

Pigging systems are designed so that the pig is loaded into the launcher, which is pressured up to launch the pig into the pipeline through a kicker line. The pig is removed from the pipeline via the receiver at the end of each run. All systems must allow for the receipt of pigs at the launcher, as blockages in the pipeline may require the pigs to be pushed back to the launcher. Some systems are designed to pig the pipeline in either direction. Most pigging systems are like this as the pigs must be removed, as many pigs are rented, pigs wear and must be replaced, and cleaning pigs push contaminants from the pipeline such as wax, foreign objects, hydrates, etc, which must be removed from the pipeline. There are inherent risks in opening the barrel to atmosphere and care must be taken to ensure that the barrel is depressured prior to opening. If the barrel is not completely depressured, the pig can be ejected from the barrel and operators have been severely injured when standing in front of an open pig door. When the product is sour, the barrel should be evacuated to a flare system where the sour gas is burnt. Operators should be wearing a self-contained breathing apparatus when working on sour systems.

A few pigging systems utilize a "captive pig", and the pipeline is only opened up very occasionally to check the condition of the Pig [http://www.piggingsystems.com/pigs.html] . At all other times, the pig is shuttled up and down the pipeline at the end of each transfer, and the pipeline itself is never opened up during process operation. These systems are not common.

Intelligent pigging

Modern pigging systems are highly sophisticated sets of equipment that consist of a standard 5-6 finned pig with an intelligent transmitter that has a global positioning system fixed on it to tell the exact location of the pig inside the pipeline while it is on the move. Along with the GPS positioner there are a host of other instruments like the internal camera that takes live video of the pipe condition inside while the pig is moving, the thickness gauge that constantly measures the thickness of the wall of the pipe as the pig moves.

As the pig moves inside the pipe data like the speed of the pig, flow, rate of fluid inside etc is measured at regular intervals. So by the time the pigging process is over the complete set of data for all the measurable parameters is ready outside.

This data is compiled and used for post pigging analysis about the condition of the pipeline from inside.

For GPS positioning, the pig has a transmitter that sends a signal outside the pipe where a recorder (above ground marker) records the time the pig passes by that precise location. The pig actually has a gyro on it that records angles and combines that with distances and when combining all 3 data sets the GPS positioning can determined. It is difficult for a GPS receiver to be located on a pig since it may be several feet below ground and/or surrounded by steel.Fact|date=May 2008

External links

* [http://www.iliassociation.org/ Inline Inspection Association]