Flashover

For the 2007 documentary see Flashover (film).

:"In electric power transmission, a flashover is an unintended high voltage electric discharge over or around an insulator, or arcing or sparking between two or more adjacent conductors."

A flashover is the near simultaneous ignition of all combustible material in an enclosed area (see also Backdraft).

Flashover occurs when the majority of surfaces in a space are heated to the point (known as fire point) at which they give off flammable gases that are hot enough to sustain combustion. Flashover normally occurs at 500 °C (930 °F) for ordinary household combustibles.

The classic example of flashover is where a piece of furniture is set alight in a domestic room. The fire on the furniture produces a layer of hot smoke across the ceiling in the room. The radiated heat from this layer causes pyrolysis (heating of the other surfaces in the room, causing them to give off flammable gases). When the surface temperatures become high enough, these gases mesmically ignite and, in the space of a few seconds, every surface in the room may be on fire.

When the phenomenon occurs in open air, it is called a firestorm.

Different types of flashover

The original Swedish terminology related to the term 'flashover' has been altered in its translation to conform with current European and North American accepted scientific definitions as follows:
* A lean flashover (accepted scientific terminology is rollover) is the ignition of the gas layer under the ceiling, leading to total involvement of the compartment. The fuel/air ratio is at the bottom region of the flammability range.
* A rich flashover occurs when the flammable gases are ignited while at the upper region of the flammability range. This can happen in rooms where the fire subsided because of lack of oxygen. The ignition source can be a smouldering object, or the stirring up of embers by the air track. The internationally accepted scientific definition of such an event is known as 'backdraft'.
* A delayed flashover occurs when the colder gray smoke cloud ignites after congregating outside of its room of origin. The results can be very unpredictable, and if the ignition occurs at the ideal mixture, the result can be a violent . The internationally accepted scientific terms for this process are either smoke explosion or fire gas ignition depending on the severity of the combustion process.
* A hot rich flashover occurs when the hot smoke with flammable gas ratio above the upper limit of flammability range and temperature higher than the ignition temperature leaves the compartment. Upon dilution with air it spontaneously ignites and the resultant flame can propagate back into the compartment, resulting in an event similar to a rich flashover. The internationally accepted definition of this process is known as auto-ignition which is another form of fire gas ignition.

Dangers of flashovers

Flashover is one of the most-feared phenomena among firefighters. Firefighters are taught to recognize flashovers and avoid backdrafts. For example, they have certain routines for opening a closed door in a building on fire, such as sitting beside the door instead of in front of it, and to be ready to fight shooting flames.

Despite superior protective gear, a firefighter has less than 17 seconds to evacuate a flashover environment if wearing proper NFPA approved gear.

Flashover indicators

The following are some of the signs that firefighters are looking for, when they attempt to determine whether a flashover is likely to occur.

* The room is closed or mostly closed, so the oxygen of the room has been consumed. In this situation, a flashover is plausible. Flashovers in open air are very rare.

* "Rollover" or tongues of fire appear (known as "Angel Fingers" to firefighters).

* There is a rapid build up of heat. This is generally the best indication of a flashover.

Firefighters memorize a chant while in training "Thick dark smoke, high heat, rollover, free burning." So they memorize the four signs of a flashover.

The color of the smoke is often considered too, but there is no connection between the color of the smoke and the risk of flashovers. Traditionally black, dense smoke was considered particularly dangerous, but history shows this to be an unreliable indicator. For example, there was a fire in a rubber mattress factory in London in 1975, which produced white smoke. The white smoke wasn't considered dangerous, so firefighters decided to ventilate, which caused a smoke explosion and killed two firefighters. The white smoke from the pyrolysis of the rubber turned out to be extremely flammable.

See also

* Backdraft
* Firestorm
* Charleston Sofa Super Store fire

External links

* [http://www.metacafe.com/watch/682670/from_living_room_to_inferno_in_under_2_minutes/ Living Room Flashover Video]
* [http://www.firetactics.com/FLASHOVER.htm Rapid Fire Progress & Flashover related fire development]
* [http://www.firetactics.com/SHAN%20RAFFEL%20IFE.htm Realistic hot fire training to deal safely with flashover and backdraft]
* [http://www.fireflash.nl/?lang=en Flashover / Backdraft training]
* [http://www.ffb.uni-karlsruhe.de Photo and video of a flashover in a living room (Forschungsstelle für Brandschutztechnik (University of Karlsruhe)]