Chain tool

Chain tool
Chain tool
Classification Bicycle tools
A typical chain tool. With a chain placed on the central sprocket, the screw is turned until a pin is pushed from the linkage

A chain tool is a small mechanical device used to "break" a bicycle chain in such a way that it can be mended with the same tool. A bicycle chain has links and plates that are pinned together; these pins can be pushed out with the chain tool. Because the pins are pushed out gradually with a screw, they can be partially removed or fully removed, depending upon the intention of the user.

The chain tool has two positions where a chain can be inserted perpendicular to the tool, one close to the movable screw portion, and one lower down just above the fixed end. In each position, there are a pair of protruding tabs; one fits into the center of one link of the chain, the other fits into the center of the next link. With the chain properly in place, the pin is held in the center of the tool, so that the tip of the movable screw can press on the end of the pin. The end of the screw is slightly narrower than the pin, so that it can press the pin through the link. Often the end of the screw is a removable piece which can be replaced when worn.

Variations and alternatives

Most chain tools are designed for chains where the links have flat plates. For chains with complicated shaped plates designed to facilitate smooth shifting, specific chain tools are available which are identical in design and operation, but have the ears protruding into the chain shaped in cross section to fit the links of the particular chain in question precisely, so as to hold the pin in the all-important vertical alignment with the screw of the tool.

Some chain tools are better at removing pins than they are at inserting them. It is a fact that once completely removed, chain pins are almost impossible to insert unless the tool has been specifically designed to do so. Users get round this limitation of some tools by never completely removing a pin that they intend to replace. They push the pin so that the chain can be broken, to shorten it for example, but so that it is firmly retained in the furthest plate. It this way even simple chain tools can press the pin back into place. Sadly, the instructions that are supplied with such tools fail to point out the best ways to proceed.

While a chain tool is required to shorten simple chains on a bicycle, and as described above, can often be used to reconnect them, there are fast-release chain links that allow repeated making and breaking of a chain. They are connected by hand pressure but often need a pair of needle-nosed pliers for removal. These links invariably replace a pair of outside plates on a chain, so joining two sets of inside plates. Bicycles with a single front chainring and rear sprocket (for example bicycles with hub gears or coaster brake hubs) may have a master link on the chain which holds the pin in place with an easily removable c-clip. Some master links are bevelled on top, and can interfere with the smooth operation of a derailleur system. Some derailleur suppliers have produced a chain with a fast-release link, made with straight plates to suit their derailleur products.

A chain tool is usually needed to shorten a chain, even when a fast-release link is being used, unless the combined number of links plus the connection link just happens to be the length required. Consider the following example.

Assume that an old derailleur chain is to be replaced with a new chain containing a suitable fast release link, supplied with it. The old chain is broken with a chain tool to remove it, and counting the links it is noted that there were 112 in total. The new chain should have the same length, but counting its links concludes that including the fast-release link there are 116 of them. (The chain link count on a new chain will not necessarily agree with the number given on its packaging.) A chain of this type is provided with inner plates at both ends for this purpose. Bearing in mind that the chain must end up with two sets of inner plate ends after the shortening, then the chain tool can be used to completely remove four links. The fast-release link plates are installed by hand as if they were a set of outer plates, and can be fixed in place by hand pressure alone. There are variations of the method in use, but in each case a chain tool will usually be needed.


Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • Chain (disambiguation) — A chain is a sequence of connected links. Chain may also refer to: Chain may refer to: Necklace a jewelry which is worn around the neck Mail (armour) (or chainmail ), a type of armor made of interlocking chain links Chain tool, small mechanical… …   Wikipedia

  • Chain migration — has multiple meanings. It refers to the social process by which immigrants from a particular town follow others from that town to a particular city or neighborhood, whether in an immigrant receiving country or in a new, usually urban, location in …   Wikipedia

  • chain saw — chain ,saw noun count a tool used for cutting down trees, with a blade consisting of a set of connected metal points that are driven around very fast by a motor …   Usage of the words and phrases in modern English

  • Tool — For other uses, see Tool (disambiguation). A modern toolbox. A tool is a device that can be used to produce an item or achieve a task, but that is not consumed in the process. Informally the word is also used to describe a procedure or process… …   Wikipedia

  • tool — I (New American Roget s College Thesaurus) n. instrument, implement, utensil, device, machine; cat s paw, dupe, henchman, intermediary. See instrumentality. II (Roget s IV) n. 1. [An implement] Syn. implement, utensil, machine, instrument,… …   English dictionary for students

  • Chain whip — This article is about the Asian melee weapon. For the bicycle repair tool, see Chain whip (bicycle tool). An example of a chain whip The chain whip is a weapon used in some Asian martial arts, including Chinese martial arts, in addition to modern …   Wikipedia

  • chain saw — noun portable power saw; teeth linked to form an endless chain • Syn: ↑chainsaw • Hypernyms: ↑power saw, ↑saw, ↑sawing machine * * * noun : a portable power saw that has teeth linked together to form an endless chain and is usually used for the… …   Useful english dictionary

  • Chain (length) — Unit of length name = chain m=20.1168 accuracy=6A chain is a unit of length; it measures 66 feet or 22 yards (20.1168m). There are 10 chains in a furlong, and 80 chains in one statute mile. An acre is the area of 10 square chains (that is, an… …   Wikipedia

  • tool — tooler, n. toolless, adj. /toohl/, n. 1. an implement, esp. one held in the hand, as a hammer, saw, or file, for performing or facilitating mechanical operations. 2. any instrument of manual operation. 3. the cutting or machining part of a lathe …   Universalium

  • Chain (unit) — 1 chain = SI units 20.11680 m 2,011.680 cm US customary / Imperial units 22.00000 yd 66.00000 ft A chain is a unit of length; it measures 66 feet or 22 yards or 100 links …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”