Necking (engineering)

Necking (engineering)
A polyethylene sample with a stable neck.

Necking, in engineering or materials science, is a mode of tensile deformation where relatively large amounts of strain localize disproportionately in a small region of the material.[1] The resulting prominent decrease in local cross-sectional area provides the basis for the name "neck". Because the local strains in the neck are large, necking is often closely associated with yielding, a form of plastic deformation associated with ductile materials, often metals or polymers.[2]

Formation

Necking results from an instability during tensile deformation when a material's cross-sectional area decreases by a greater proportion than the material strain hardens. Considère published the basic criterion for necking in 1885.[3] Three concepts provide the framework for understanding neck formation.

  1. Before deformation, all real materials have heterogenieties such as flaws or local variations in dimensions or composition that cause local fluctuations in stresses and strains. To determine the location of the incipient neck, these fluctuations need only be infinitesimal in magnitude.
  2. During tensile deformation the material decreases in cross-sectional area. (Poisson effect)
  3. During tensile deformation the material strain hardens. The amount of hardening varies with extent of deformation.

The latter two items determine the stability while the first item determines the neck's location.

Graphical construction indicating criteria for neck formation and neck stabilization.
Graphical construction for a material that deforms homogeneously at all draw ratios.

The plots at left show the quantitative relation between hardening (depicted by the curve's slope) and decrease in cross-sectional area (assumed in the Considère treatment to vary inversely with draw ratio) for a material that forms a stable neck (top) and a material that deforms homogeneously at all draw ratios (bottom).

As the material deforms, all locations undergo approximately the same amount of strain as long as it hardens more than its cross-sectional area decreases, as shown at small draw ratios in the top diagram and at all draw ratios in the bottom. But if the material begins to harden by a smaller proportion than the decrease in cross-sectional area, as indicated by the first tangent point in the top diagram, strain concentrates at the location of highest stress or lowest hardness. The greater the local strain, the greater the local decrease in cross-sectional area, which in turn causes even more concentration of strain, leading to an instability that causes the formation of a neck. This instability is called "geometric" or "extrinsic" because it involves the material's macroscopic decrease in cross-sectional area.

Neck stability

As deformation proceeds the geometric instability causes strain to continue concentrating in the neck until the material either ruptures or the necked material hardens enough, as indicated by the second tangent point in the top diagram, to cause other regions of the material to deform instead. The amount of strain in the stable neck is called the natural draw ratio[4] because it is determined by the material's hardening characteristics, not the amount of drawing imposed on the material. Ductile polymers often exhibit stable necks because molecular orientation provides a mechanism for hardening that predominates at large strains.[5]

References

  1. ^ P.W. Bridgman, Large Plastic Flow and Fracture, McGraw-Hill, (1952)
  2. ^ A.J. Kinloch and R.J. Young, Fracture Behaviour of Polymers, Chapman & Hall (1995) p108
  3. ^ Armand Considère, Annales des Ponts et Chaussées 9 (1885) pages 574-775
  4. ^ Roland Séguéla Macromolecular Materials and Engineering Volume 292 Issue 3 (2006) pages 235 - 244
  5. ^ R. N. Haward J. Polym Sci Part B: Polym. Phys. 45 (2007) pages 1090-1099

Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Necking — can refer to: Making out, a term for heavy kissing of the neck or petting of that area Necking (engineering), the process by which a ductile material deforms under tension forming a thin neck Necking, a behavior of giraffes Necking up or necking… …   Wikipedia

  • Deformation (engineering) — This article is about deformation in engineering. For a more rigorous treatment, see Deformation (mechanics). Compressive stress results in deformation which shortens the object but also expands it outwards. In materials science, deformation is a …   Wikipedia

  • Structural engineering — is a field of engineering dealing with the analysis and design of structures that support or resist loads. Structural engineering is usually considered a speciality within civil engineering, but it can also be studied in its own right. [cite… …   Wikipedia

  • Tensile strength — sigma {UTS}, or S U is the stress at which a material breaks or permanently deforms. Tensile strength is an intensive property and, consequently, does not depend on the size of the test specimen. However, it is dependent on the preparation of the …   Wikipedia

  • .358-378 RG — Infobox Firearm Cartridge name= .358 378 RG caption= .358 378 RG origin= Sunnyvale, California type= Wildcat cartridge service= used by= wars= designer= Joseph D Alessandro design date= March 2002 manufacturer= production date= number= variants=… …   Wikipedia

  • Polymer — Appearance of real linear polymer chains as recorded using an atomic force microscope on surface under liquid medium. Chain contour length for this polymer is 204 nm; thickness is 0.4 nm.[1] A polymer is a large molecule (macromolecule …   Wikipedia

  • Fracture — For other uses, see Fracture (disambiguation). v · d · e Materials failure modes …   Wikipedia

  • Stress–strain curve — During testing of a material sample, the stress–strain curve is a graphical representation of the relationship between stress, derived from measuring the load applied on the sample, and strain, derived from measuring the deformation of the sample …   Wikipedia

  • Ultimate failure — In mechanical engineering, ultimate failure describes the breaking of a material. In general there are two types or failure: fracture and buckling. Fracture of a material occurs when either an internal or external crack elongates the width or… …   Wikipedia

  • Column — For other uses, see Column (disambiguation). National Capitol Columns at the United States National Arboretum in Washington, D.C …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”