Drawbar force gauge

Drawbar force gauge

A drawbar force gauge is a gauge designed to measure forces on a machine tool's drawbar. These types of machines are found in metalworking, woodworking, stone cutting, and carbon fiber fabricating shops. Many modern machines generate well in excess of 50,000 N (12,000 lbf). Measuring and maintaining this force is an important and necessary part of a machine shop preventative maintenance plan.

Contents

How drawbar force gauges work

Modern drawbar force gauges typically are based on a force sensor that uses bonded strain gauges and electronics to convert the resulting output into a digital display for the user to view. Earlier versions of these gauges sometimes also used a sealed hydraulic cavity with a pressure gauge to measure and display force. These hydraulic gauges are generally considered less accurate because of the physical limitations of the indicator.

Why drawbar force is measured

Drawbar force gauges allow early detection of problems with the spindle's Belleville spring stack, verification of performance of the clamping system as a whole, help prevent damage to spindle taper and other machine features critical to machining accuracy, and ultimately help to keep the machine operator safe.

Drawbar force measurement has been made much more important in recent years with the introduction of radically higher RPM machines. These machines are necessary to work the modern materials required in a multitude of applications—new types of composite wood material, carbon fiber, and high strength materials such as titanium. High speed machining of these materials is considered to begin at 10,000 rpm and may reach as high as 50,000 rpm. The need for regular verification of the spindle clamping system becomes obvious.

As the required machining speeds become higher, the need for machines to be built with smaller diameter spindle components increases. When the spring pack, bearings, and hydraulic units become smaller, the stresses placed upon them become greater. As a result, the clamping system will remain in good shape for fewer and fewer "cycles", or "clamp/unclamp" procedures. Again, this requires gauges and routine procedures to monitor this process. Many operators do not realize that this is something that has changed over time.

Any metal or wood working machine that takes advantage of the HSK taper system should be routinely checked. The slightest stroke mis-adjustment, dirt, or slight wear of the drawbar system can result in significantly reduced holding force. A preventative maintenance schedule, with a strict timetable for testing is a necessity when operating any type of high speed machine utilizing the HSK system.

Drawbar force gauges are able to detect broken or weakening components of the drawbar clamping system, can give indications that the unit needs lubrication, detect gripper mis-adjustment, or demonstrate that the incorrect retention knob is being used for the machine. With a highly accurate electronic gauge, all of these deficiencies can be noted and corrected. Many hours of expensive machine operating time can be put to use while avoiding fretting, chatter, "stuck" tool holders in a spindle, etc., by employing proper preventative maintenance techniques using an accurate electronic gauge and other spindle health management tools.

Drawbar force gauges in tool holder standards

The following tool holder standards specifically address tool retention force as measured by a drawbar force gauge:

  • HSK standard ISO 12164-1: Holow taper interface with flange contact surface—Part 1: Shanks—Dimensions
  • Steep Taper standard ASME B5.50: 7/24 Taper Tool to Spindle Connection for Automatic Tool Change
  • Capto Taper standard ISO 26623-1: Polygonal taper interface with flange contact surface—Part 1: Dimensions and designation of shanks

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Drawbar (machine tool) — A drawbar or spindle drawbar is a clamping mechanism for toolholders on machine tools. The toolholder or machine taper itself is held by the drawbar and applies force to the spindle, especially when spinning at high speeds. See also Drawbar Force …   Wikipedia

  • Horsepower — hp redirects here. For other uses, see HP (disambiguation). Horsepower (HP) is the name of several units of measurement of power. The most common definitions equal between 735.5 and 750 watts.[1] Horsepower was originally defined to compare the… …   Wikipedia

  • Steam locomotive — A steam locomotive is a locomotive powered by steam. The term usually refers to its use on railways, but can also refer to a road locomotive such as a traction engine or steamroller.Steam locomotives dominated rail traction from the mid 19th… …   Wikipedia

  • Coupling (railway) — Knuckle (AAR Type E ) couplers in use ICE coupler A c …   Wikipedia

  • NYC Niagara — Niagara #6015 in Indianapolis, Indiana, June 30, 1956. A few days later, the locomotive was retired Power type Steam Builder Alco Schenectady Build date …   Wikipedia

  • Chuck (engineering) — Self centering three jaw chuck and key with one jaw removed and inverted showing the teeth that engage in the scroll plate. The scroll plate is rotated within the chuck body by the key, the scroll engages the teeth on the underside of the jaws… …   Wikipedia

  • Collet — For other uses, see Collet (disambiguation). Collets A collet (  / …   Wikipedia

  • Distributed power — In rail transport distributed power refers to the placing of additional locomotives at intermediate points in the middle of the train, remotely controlled from the leading locomotive, to allow longer trains where operational considerations or… …   Wikipedia

  • 2-8-4 — In the Whyte notation, a 2 8 4 is a railroad steam locomotive that has one unpowered leading axle followed by four powered driving axles and two unpowered trailing axles. This locomotive type is most often referred to as a Berkshire, though the… …   Wikipedia

  • Norfolk & Western 2156 — Power type Steam Builder N W s Roanoke Shops Serial number 317 Build date March 19, 1942 …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”